Phaeton :: Code 01583 - Leak In System Detected / Level Fault Error
Nov 16, 2011
In the past few weeks I have seen an intermittent "Level Error-Workshop". However every suspension function has worked perfectly, and no height was lost even while sitting at the airport for a week.
How to track down the leak. I can see a tank pressure of about 13 PSI. Is that about right. I did a raise / lower while VCDS was connected and there was a pressure drop to about 11.7 PSI but no level error. What is the correct range of tank pressure settings?
Address 34: Level Control Labels: 3D0-907-553.lbl
Part No: 3D0 907 553 C
Component: LUFTFDR.-CDC- 3C3V0 1122
Coding: 0005521
Shop #: WSC 01065 000 00000
VCID: 2757057592F60B6
1 Fault Found:
01583 - Leak in System Detected
000 - - - Intermittent
View 4 Replies
Advertisement
I recently had my front axles replaced and a week or two after I'm getting this code for level fault workshop. Do you think it could be something they did when they replaced the axles. I also had the secondary radiator replaced.
View 11 Replies
Noticed the vehicle was riding low on the passenger sign, and then received a fault code on the driver's screen "Level Fault Workshop" what is this? I can't find in the faq section...
View 9 Replies
I've been getting this "system fault workshop!" error message popping up like crazy. Its got a picture of a key, and makes the audible beep when it appears. on a short drive to work, maybe 10 minutes, it will randomly come on and beep anywhere from 3-10 times during my drive. The car starts and drives perfectly fine. This has been happening for a little over a week now. I noticed one post about this before, but that owner seemed to have different symptoms as their car wouldn't start. I really would hate to bring it into the dealership, as I've just paid them a small fortune fixing different things to finally get down to the bottom of it to find out i needed new fuel pump modules.
View 3 Replies
It all started with a fuel cap loose light (it wasn't) after a day or two the MIL came on and got this code I reset it but I'm sure it'll come back since there's probably a real leak. What can I check myself to find this leak?
View 11 Replies
This is the code i pulled from Vag. Its not the gas cap...
VCDS Release 805.0: Generic OBD2
Mode 03: Emission related fault codes
Address 10 (Engine): 1 Fault Found:
P0456 - EVAP System: Very Small Leak Detected
View 8 Replies
2004 VW touareg v6 - engine light on - autozone diagnosed as code P0456. Possibly gas cap, so I replaced with aftermarket gas cap from auto zone. Light still on. What can I do or replace to fix problem. I read something about a N60 or N80 valve. Is this something I can buy and replace myself. Most of my mechanical experience is related to working on a 85 CJ7 with an inline 6cyl or Chevy trucks. If the N valve is a easy fix, any instructions and pictures of how to do this.
View 1 Replies
Secondary air injection system leak detected-Bank 1 & 2... 2003 miles on my car and the CEL pops on this morning. VCV bodies are being replaced tomorrow. The tech didn't fully understand what parameters to test for or what conditions would be present to set this code, I can't say that I do either... the flapper could possibly play a role in this..?
View 5 Replies
CEL came on after a couple of driving cycles showing code P0456 (evap emission control system very small leak detected)............. car drives fine has good gas mileage.....
View 13 Replies
I own a 98 f-150 5.4 with 70,000 miles. I get a check engine light (code p0455-large leak detected in evaporative emission control system).
Replaced the gas cap with an after market 'stant' ( I believe was the manufacturer) brand. The check engine light went away for 4 days then came on again.
No obvious vacuum line leaks.... Puzzled.
View 14 Replies
I have 2004 V8 Phaeton ,the message LEVEL FAULT WORKSHOP. keeps appearing ,then disappearing, sometimes it will stay until the car is turned off,. When it comes some times even on long highway journeys I wont see it at all!. When it comes on nothing seems to change.
View 6 Replies
I have a 2004 Phaeton which has been having multiple problems with error codes. I keep getting Level Fault Work Shop. When this code comes on the ABS and EPS also fail and can only be reset by restarting the car. My VW dealer is having significant trouble finding the problem. Thus are they have repalaced the batteries, and the control module for the ABS. I think an option could be the battery control module.
View 9 Replies
My r32 mk5 is throwing that code.
I replaced new o2 sensor with oem new one.post cat on driver side.
I have erased dtc and drove 15 miles dtc came back again.
Now i have replaced catalysator on driver side and same thing again.
View 2 Replies
The CEL tripped yesterday and this is the code autozone pulled. WHat does it mean.
View 3 Replies
One of my issues is a "level fault workshop" message and abs/ esp lights that only appear once I put the car in gear and start moving.
The car does seem to raise and lower normally and there doesn't seem to lose height over night.
To check if it's a particular wheel height sensor, what controller should I scan in vcds? Nothing related to suspension came up in my full auto scan.
I did have an intermittent brake light switch code, could that generate the level fault?.
View 4 Replies
My 2004 Phaeton with a little over 100k miles on it has been giving me a problem with the air ride suspension. When starting the vehicle, a "Level Fault - Workshop" message is displayed on the instrument cluster, and the car has been slowly sinking as the air ride (I presume) slowly deflates. Around 10,000 miles ago, I had a problem with the suspension, but that time the car immediately and actively sank; this was solved by replacing the air ride computer (it is the B, not C-type). I've tried replacing the computer with another B-type computer, but to no avail. The local VW dealer and an independent import car garage have told me some things, and I would like to learn more about this problem and possible ways to try and solve it.
1. I have been told that no voltage is making it from the computer to the left front sensor. Dealer says its the computer, but could this possibly be the wiring harness or a bad connection? If so, how do I get into the wheel well in order to test this hypothesis? My best guess is it isn't the computer, as the car never actively sank (this happened when the original computer went bad).
2. I have also been told that the right rear sensor is bad. Is this a part I can replace with a modest amount of auto knowledge? I do my own oil, replace brake pads/rotors, etc. If so, any drawing/maintenance manual parts list available?
3. I have heard conflicting reports as to a freshly-ordered sensor being and not being compatible with the B-type computer. Dealer told me new sensors will only speak to a C-computer; independent garage told me new sensors will speak to my B computer. Who is correct?
From a few hours of internet browsing from the first instance and this second instance of failure, it seems this is a somewhat common issue with the 2004 Phaeton.
View 7 Replies
My car is a Prius Plus 2012.
One day, I decided to go to a mechanic to clean the EGR pipe. Only the pipe, not the whole EGR. It was an extremely simple operation a mechanical one, not electrical etc. Starting from that day, when I go with the car, from time to time, check engine lights up. For a fraction of a second to up to 2 seconds then it disappear.
The car behave itself without a problem. But still the on-off check engine is really annoying.
So a went to the dealer. Put the car on tester.
Result: no code error !
I went to another garage , put another tester on the car, no error..
How can I actually see what the error is if nothing is stocked in the ECU of the car?
View 4 Replies
I bought my first VW about 3 months ago (so excited!) It's a 2003 Passat, 5 spd, 1.8t. I've had one thing happen so far (until yesterday). On 4 separate occasions when I'd go to start it, it would crank for a few seconds before it would start. Then once it was running the EPC light would turn on. It seemed to be running normally but I turned it off and restarted it and it started normally and the light extinguished (the first three times). The last time (about a week and a half ago) it kept doing it each time I started it, and upon starting probably the 4th time in a row the MIL came on. I drove it about a mile, turned it off for a few minutes, then turned it back on and it started normally with no malfunction lights on. It's been normal since then. Until yesterday...
Yesterday as I'm accelerating from a stop light (I think I was in 3rd) all of the sudden the engine started running really rough and the MIL came on. I turned around and drove about 2 miles back to where I started at about 20mph. The MIL would be steady while coasting and flash while pressing the accelerator. I got a hold of a diagnostic computer and it came up with 3 codes...
1) P0322 Ignition/Dist Engine Speed Input Circuit No Signal
2) P0302 Cylinder 2 Misfire Detected
3) P0302 Cylinder 2 Misfire Detected PENDING
View 3 Replies
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 Replies
I have a 2004 VW Phaeton.
Today, the sound system failed, then shortly after, the navigation system failed.
On the console, if I press any map/navigation buttons, the error message "Navigation System Unavailable" is displayed.
If I press an audio related button, the error message "DSP system is unavailable". I took it to a private vw repair shop and a vw dealer. What was causing the issue.
I am now headed to a vw dealer with certified phaeton tech. I looked towards fuse issue, but they appear to be ok..
View 10 Replies
My CEL came on and I took it in to dealer. They replaced the EVAP line and purge valve. My CEL came on again that same week and supposedly it detected a small leak (sporadic, same code as previous), they ran test and did not detect any leaks. They finally told me that I might have to replace the canister if CEL comes on again for same code.
View 3 Replies
