Transmission on 04 V8 phaeton is slipping between first & second gears. transmission repair $4-10K. thought of just taking out the first gear via reprogramming (had a jag where you could do that for snow/ice conditions). do yo think taking out the first gear will cause extra wear & tear on the drive train? The first gear seems to be very short.
View 16 Replies2003 rav4 . Recently, my rav4 has been slipping from gears 2-3. After exhaustive research, I found out that my car is known to have a bad ecm. So I decided to get a fixed ecm and replace it in my car. Car still slips so, thinking the ecm is good, I had my transmission rebuilt. After rebuilding my transmission, it still slips from gears 2-3. Do I need to replace my ecm again to coincide with the new transmission? I'm completely at a lost.
View 12 Replies2003 Explorer with a slipping transmission...codes are P0731, P0732, P0733... Just had a new solenoid pack installed last week when O/D light came on and truck was clunking into reverse. Now, after new pack was installed the forward gears are slipping all over the place!
View 5 RepliesI own a 2005 f-250 superduty with the 6L diesel. Just recently when I leave to work in the morning I notice the trans shifts slow through the gears and when it does start to shift it will start slipping then kinda vibrate for a few seconds then finally shifts into the next gear. It will do this through all the gears until I get up to speed on the highway. After it warms up it shifts and drives great until I let it sit for around 8hrs or more. I really hope I don't need a new Transmission considering I bought this truck as is from the dealership just a little over a month ago. I have checked the trans fluid it is full, I even drained all the fluid and replace with new and it still does the same thing.
View 4 Replies2004 V8 with 63,000 miles owned from new
When starting from cold there tends to be a hesitation, followed by what feels like car slipping into gear. Feels like past experiences with other cars having low levels of transmission fluid. In addition, display always shows PRND... rather than displaying actual gear. Related?
As I recall this is a sealed system and there is no method in any of the manuals for checking the fluid level. Correct?
My battery(ies) are likely at the end of their lives, which may be the reason for the random warning and periodic resetting of infotainment system.
Planning on putting in in two weeks to check batteries and deal with a few other things but do not want to cause any damage.
My issue is that the car (04 V8 6speed 210k miles) will be in 6th gear or 5th going into 6th and the gear would disappear off the dash and the car would act like it's in neutral, RPM's shoot up cause i'm on the gas. When I get off the gas and let the car return to idle it figured out what gear it was in and started running normal again.
View 2 RepliesMy transmission seems to be slipping a little, but not regularly and when tested by the mechanic it shows no transmission problem. He did point out that the fluid was really black and had specks of metal in it. However, he suggested that I not replace the fluid because it has been experience that people change out the fluid and then their transmission fails. He's a mechanic I've never used before, but don't know if I should trust his assessment. I've owned the car its entire life and it only has 89,000 miles on it, primarily in San Francisco, and I'd like to get a lot more miles out of it.
View 4 RepliesI just bought a 2004 prius with 187000 miles for $2,500 and it has a triangle with an exclamation point in it and check engine light on and another symbol on the dash. When I take off it revs like the transmission is slipping and it only will get up to about 50 mph.
View 17 RepliesI have a 2006 Prius with 103k miles that runs and drives great but sometimes with no warning will display the red triangle and check engine light and seem to slip out of gear. All I can do is coast to a safe spot to reset the codes. Once I reset the code it runs fine again.
View 2 Replies2004 2.4L suv with 98K + miles. Transmission was slipping periodically - fluid levels were fine. Someone suggested changing fluids as it may be contaminated. This car has a manual option also that I don't normally use but I did take car out on a longer drive and it shifted as I directed. Since car is almost out of warranty (naturally) I was trying to find answers as I don't feel dealership will be honest with me. While I have not had an actual slip (engine revving and not moving) since fluids changed 2 weeks ago it does seem slow to shift. Since it was not consistent someone said the sensor may be going.
View 4 RepliesTransmission won't go into drive until I give it gas and then hard shift between 1&2 then a little slipping when I get on it in higher speeds , fluid and filter brand new, threw a speed sensor so code I replaced with new but no change, don't know what to do and can't find out why speed sensor code went off changed but didn't fix? Can't drive truck!!!
View 3 RepliesI have a 2004 4x4 with 305K on it. Never changed the transmission fluid and I think its slipping a bit.
Beentold that I should not change the fluid because the new fluid would somehow damage something and to just not worry about it.
So OK to change the fluid or not?
2005 F-150 5.4L RWD
I purchased this truck about 2 years ago, with about 70k miles. Previous owner had transmission work done, but I'm not sure if it was a rebuild, new, or refurbished. About 8 months ago I experienced hesitation, and frequent stalling when coming to a stop. Pulled the engine codes, and they said it was throttle body related. I thoroughly cleaned the throttle body assembly inside, with the battery disconnected, went through the idle re-learn process, and it drove fine for a few days. Took it into the shop, and they did a tune up and replaced several plugs and coils. Since then, it's run great.
A couple of weeks ago, a whining/buzzing noise was coming from the engine compartment, getting much louder as RPMs increased. Got the oil changed a week ago (it was overdue), and the tech at the quick lube shop said the noise was from the drive pulley(s), and that they should be replaced.
Today, I was waiting for the parking lot at work to open, sitting in park. I quickly switched to Drive, and the trans didn't seem to engage (Auto Trans). The engine revved, I let off the gas, and it then engaged and I scooted into a parking spot. After work, on the way home, there were similar issues at the beginning of the drive, mainly when slowing down/stopping/down-shifting. Most of the drive was on hwy, and I managed to get by okay going around 60 mph, with some spikes in RPM's occasionally when I would accelerate (no Tach, so I'm going by sound). Half way home on the high way, the O/D Off light starting quickly blinking, and the odometer screen read "TRANS FAULT". I managed to make it off of the highway, and stopped at the first red light, where the engine stalled. Turned it back on, put it in gear, and it drove fine for about 5-10 minutes on back roads, with no lights/notices. The last 2 miles home I experienced a lot of slipping, and high revs. When I backed into my parking spot, there was noticeable leaking... Trans fluid was leaking fairly quickly. I hadn't noticed any trans fluid leaking before today... I went out to run the engine and take a short trip to warm up the fluid to get a reading, but it wouldn't engage in Forward or Reverse at all. Pulled the dipstick out, while "cold", and there was nothing... I'm assuming that it's drained drastically, and is extremely low or gone.
I have an early model year 2004 Touareg which has lately developed what appears to be a slipping problem when changing gears from 5th to 4th when decelerating or the same when accelerating strongly and downshifting. When switching over to tiptronic mode, its not clear if that apparent slipping goes away or changes. It definitely isn't as severe but that could be due to perception or the RPMs where the shifting is occurring.
The only real interesting characteristic of this clunk and lurch that is experienced is that it only happens when the car is warm -- I've been watching the transmission oil temperature, and it appears to start happening as it passes through 200 degrees. When it starts, the lurch/clunk is small and not too bad. As the car reaches temperature, it reaches if full lurch/clunk potential.
I have taken it to the dealer once and they have "upgraded software" that was supposed to clear up the problem, but did not.
My wife was driving my Stage 1 R last night (by herself) and she ran into an issue where when she tried to leave from a red light, the clutch was slipping through the first three gears and she could barely get up any speed. She pulled over, let the car sit for a few minutes and then started going again with no issues.
She drove home about 5 miles and told me about what happened. The car smelled like burning clutch, but when I took it out for a quick test drive, everything seemed fine.
I am at around 5000 miles and have never had any issues before and I don't ever do high-rpm launches. So, could this have been a fluke or a sign of the clutch/pressure plate issues people have been having?
I have an 04 2.7 litre V6 AWD Santa Fe with 189235 KM , with a Shiftronic transmission, recently, while in "d", the transmission would feel like its slipping or perhaps trying to down shift, its hard to tell what it's doing really, but if you then slapped it over into shiftronic, it would operate fine, no slipping, locks into gear strongly, indicating that its not mechanical, but related to the computer controlling "drive" function of the transmission, I flushed the transmission just after the symptoms arrived (using the correct SP3 fluid) and this made no difference, the old fluid, although ready to be changed, was not burnt or blackend. I thought of getting it reflashed ( read it online) but I am not sure it will work, especially if its like a sensor or something.
View 3 Replies2004 Dodge Neon SXT ... Let me say first, I know very, very little about cars. But it all started when I was driving down the road and my car was bucking around 40-45 mph, it stayed that way up until I put some gas in the car the next day and the car started shaking violently when I turned it on. Ever since then my car has been not able to change gears. Reverse works normally however. Now the speedo doesn't work at all and somehow the has gauge will fall or rise depending on whether I'm stopping or going.
So I ran to AutoZone and got a diagnostic ran on my car. It gave me codes P0700, P0731, and P0720. I kept calling around and got horrific quotes around a thousand bucks and mechanics saying my transmission was out. However, I turned it over to a close friend who could work on it for free and has some mechanic experience. The first thing we did was replaced both the output and input speed sensors, which didn't fix it. Then I got a new transmission control module, which for my car I assume it is the TCM and solenoid. Still. That didn't fix the problem. Those were some common fixes I found online for neons. But what else it could be.
I have a 04 Explorer 4.0 4x4 with 130,000 mi. It all started about 3 months ago. The truck would neutral out while driving. After changing tranny fluid and filter, along with rear speed sensor the problem returned after driving 3-4 miles. After digging deeper I found the transfer case was bone dry and fried inside. Replaced the TC and check fluid level again. Back out of garage and drove the vehicle approx. 2 miles. Stopped to grab a coffee and left truck running. Returned to find I had no reverse or drive. This is after driving it to where I was. Towed truck back home.
I noticed the vehicle would start in gear. Replaced neutral safety switch ( grooves properly aligned ). Started truck, reverse lights come on when in reverse.. The problem now is when I put vehicle into R,N,D,3,2,1, the truck does one thing... REVERSE. All gears put truck into reverse, no forward movement at all. I attempted to replace safety switch a couple of weeks ago but was unable to remove the nut holding the lever on. 2 days I spent on that nut. Now I'm wondering if I did something inside the tranny when I was wrenching on that nut for 2 days?
I was driving home from work and out of the blue my truck started slipping gears so wen I got home I looked under my truck at the transmission and drive shaft and from the picture I attached that is what I saw...
View 4 RepliesI have a 2008 RX350 AWD with only 500 miles on it so far and I am starting to get concerned about what seems to be excessive slipping or a delay in response in the trans. Under normal forward driving the trans seems to shift very smooth. The problem occurs under situations where I am coming to a near stop, basically coasting, and then have to accelerate again to continue forward. This could be in a slow moving traffic type situation or when maneuvering through a parking lot. When I try to execute a small increase in speed the engine revs but the trans doesn't respond.
It's as though it's in neutral and unable to decide which gear it should be in. After a 2 to as long as a 5 second delay it finally engages and moves forward. The condition is even worse if I am heading into a slight incline. Once it is engaged everything is fine and the subsequent shifts are very smooth. When starting from a complete stop it works perfectly. I've never had a transmission slip this much in any vehicle. There was one situation where I was almost broadsided because the RX delayed in moving forward.
I realize this is a subjective call but I am trying to determine what level of slipping in the trans is considered normal under the conditions I've described. I have searched and read past threads about issues with the earlier model years but I thought they were resolved by now. I haven't taken the RX in for service yet but I fear I will get the standard - everything is working as designed - answer from my dealership.
Like the title says. 04 Explorer.
No transmission issues ever. Immediately after doing an oil change myself for first time, get some transmission dropouts, slipping out of gear at stop lights, waiting way too long to go into 2nd, etc.
Then, started getting OD off light, and service engine. Error codes show something about wrong setting for 2nd, 5th, solenoid error... a bunch of 'em.
Anyway, guy at parts store says I must have knocked a wire loose causing misreads between cpu and transmission. It's a real pain getting under there since I'm using jack stands, so exactly what I should be looking for or at least the exact name of a connector or something so I can look it up.