Putting in my amp/sub this Friday. I was told to run wires under sills, not through the center console.
So I don't goof up and bust/damage any clips or pins , what is the correct way to remove the sills, both f & r, drivers side?
What is the trick to removing the plastic pieces framing the lower door sills? i dont wanna just start yanking i need to run a wire from the trunk forward.
View 2 RepliesI need to remove the front headlight in order to repair it. Must I remove the bumper? How?
View 16 RepliesWant to paint color of car black stealth look! Painting everything black door & rear bumper trim black.
View 2 RepliesI am getting ready to install DVD headrest players in my RX400h. I am stumped on how to remove the read shield of the seat if that makes sence? I believe the are held in by clamps from middle to top but not sure what needs done at the bottome. And I can also feel two straps at the bottom.
How to remove the back so I can run the wires down the seat from the headrests? Pictures? Diagrams?
How do I remove the interior rear door panels?
My passenger side rear door handle does not work. My mechanic fixed it once, said the cable had jumped off the pulley. I figured it can't be that difficult to fix if I can get the door panel off.
How to remove the rear door panel on my 1998 Passat. The window has come off the track, and I would like to try to get it back on.
View 5 RepliesWhat tool I need to replace the rear disc/pads in my 1998 VW Passat 1.8T. I believe is called a wind back tool and I have seen it in the web.
View 1 Repliesguides for jettas and b5's don't seem to work.
I've taken the three bolts out of the middle, the ones with the black clips on them, but don't know where to go from here. I'm assuming I'll also have to disconnect the brake light, correct?
It seemed there were screws or even glue maybe holding the deck in place close to the seatbacks - is this true? I didn't want to pull to hard on it in case it broke.
Is there any other way to access the amp without removing the deck lid? My rear right mid speaker isn't working so I'm trying to determine why
I am in middle of "trying to" change the wheel bearing and I have the hub out but I can't figure out how this bearing needs to come out.
I have done it on MKIV Golf and like most other cars there is a C clip, but i can't see a clip in this knuckle.
Is this thing press fit in there without a clip? I have seen a guide for MKIV Jetta and people say Passat is almost the same, but not until I find this C clip.
How is the red marker light lens, located on either side of the rear bumper, removed to allow the bulb on the inside to be replaced?
View 2 RepliesI'm looking for the process to remove the exterior black glossy b pillar trim on the front door. My wife decided to open my door against a ladder and it has a 3mm scratch that's going to big the piss out of me so I'm looking to replace it. Also looking for the PN as well.
View 2 RepliesI have an 02 f150 2WD with a "leveling" kit. It was on the truck when I bought it. However, the front sets noticeably higher than the rear. The rear has lifting blocks, while the front has the lifted spindles as well as the coil spring spacers. At least I think they are spacers. I had to replace lower control arm bushings a while back, and there were black plastic rings on top of the springs. Can I remove the spacers? If I can, I plan on doing that and replacing the rear blocks with whatever I need to get the stance back. I like the height of the truck now, just hate the front being higher than the rear. I do pull my boat with it.
View 2 RepliesMy 2002 B5.5 Variant received some "tough love" in a parking lot recently, with the result that one of the front marker lights (in the fender ahead of the front wheel, on the side) was broken. I see that I can push on the light housing and it'll move in a bit, but how can I remove the cover (the colored plastic bit) entirely to replace it with a new, not-busted one?
View 1 RepliesI have a 2003 W8 wagon and my front turn signal bulb went out. I need to replace it, but am having some problems. I removed the high beam cover to get to the turn signal socket, but I am having problem removing the socket. I was able to turn the socket slightly and was hoping I could just pull it back, unfortunately it doesn't seem to want to move. Is there a trick to remove the turn signal socket so I can remove the bulb? I don't want to force anything in fear of breaking something. there has to be a way.
View 1 RepliesI have to repair or replace my rear window wiper/washer unit.
How do I remove the trim inside the lift gate? I saw two screws and removed them, but it's still being held in place. Is it near the indented handes? There seems to be little square plastic screw covers in there. I couldn't remove them (I was on the road) and didn't want to hack them if they weren't.
Changing the LED on the JDM side mirrors for the Puddle Light or Illuminated Door Sills. I wanted to go with Black Light inside the cockpit and puddle light and sills.
View 8 RepliesBoth my door sills are not working I tapped a wire and now both not working all the fuses are good. Why or where the fuse is located exactly?
View 2 RepliesI have a Blizzard Pearl 2012 Toyota Prius PPP edition, I have owned it since August of 2013 and absolutely love it, the upgraded stiffer suspension is awesome. I can make 60 mph turns on freeway ramps with little to no body roll, it an insane feeling.
Now to my problem, can any of the other PPP owners tell me if all 4 door sills light up, only the passenger side door sill has ever lit up since I bought it, I thought that was the way it was meant to be but after reading on this forum it appears they all light up or at the very least both front doors light up.
I looked closely at the back door sills and they do not to be the same as the front ones as though they might not light up, guess I will have to remove them to check if they have power runnnig to them
Just recently I discover that the carpet behind the driver seat was soaking wet. I lift the carpet, dried the best I could and now I am trying to determine if the water is making it's way from the the back (back door seal) or from the firewall area.
If the water from the firewall can make it's way to the rear of the car ? Seems to me that it's not from the firewall because floor under the driver's seat is deeper and does not seem to have a water puddle in there.... but the insulation under the carpet is wet....
Why is there a gap between the front and rear windshield with a recess behind? All kinds of crap get stuck in that gap and then it is impossible to clean out. I also have to wonder if that is part of the reason there is so much wind noise. It seems to me that perhaps it gives a cleaner appearance and it is indeed nice that I don't have to worry about unsightly deteriorating rubber seals as the car ages, but it is really difficult to clean that stuff out. Also, there is a gap where the bottom of the door window frame meets the window seal where the window comes out of the door. Stuff also gets stuck in there. I need to add tweezers to my car wash kit to get all of this out.
View 2 Replies