just wondering what are the problems typically associated with a long start up. it took about 8-10 seconds from the time i put in the key fob to ignition. it was especially cold and windy today, so i know the cold had something to do with it.
View 6 RepliesI've had this passat since it had 103k. Now at 167k. It's ran good. Til now. Lately its been having a problem starting. Goto start it and it takes a good 15-20 secs to start. Eventually starts but had a couple times when it started the engine would act like it was going to die then eventually stay running. I've noticed when the car sits for awhile. About 3-4 hours or more it starts ok. But say I run to the store and let it sit for 20 min to a hour then I have problems starting it. Had a local store test battery, starter, and alternator and everything tested fine except the starter failed on startup but then passed after the car was running for a min. So replaced starter. Still having starting issues. Recently I have changed the spark plugs and valve cover gasket.
View 4 RepliesI recently bought a 98 Passat with what was thought to be an ignition switch problem.. well I changed the switch today and the problem is still there.. it would start sometimes and and sometimes it won't do anything. Not even click.. and sometimes when it starts it sounds like the starter isn't getting enough juice.. another weird thing is that I can start the car without pressing the clutch.(when it does start).. There is actually a couple of electrical oddities going on.. the moonroof would go up by itself randomly and the radio (after matket) doesn't save any of my presets. Every time I turn the car off the radio resets.. so I'm thinking some weird electrical problem is going on..
View 10 RepliesWhen I start the ignition, the horn goes off for about 1 or 2 seconds. While engine is on the horn is not operational (I press and nothing).
2006 Passat 2.0T
I have a 1.8T 2001.5 Passat, Tiptronic with an Upsolute chip. I recently had the turbo replaced (under warranty for the same stock one). After the turbo reinstall, the car did this after driving it a while: I ran it hard and spooled up the turbo good a few times, and then parked the car. I would wait 45-60 minutes. When I tried to start the car it wouldn't start for like 8 seconds on the ignition, and then it would start but in EPC mode!
The first time this happened I panicked, drove it home (just to make sure I got home.) I then tried again and it started fine and no more EPC. Also, if I wait much longer like 3 or 4 hours, it never happens. Since the first time, this has happened like 10 times or more. But now, I just turn it off right after it starts in EPC, turn it again, and it works fine.
The first time it happened I got some kind of codes, but I didn't save them and cleared them. I figured since it happened again, I would get the codes again, but they're not there. I took it to the dealer, and of course, they can't duplicate it. The codes where like speed implausible or not there or something but I can't remember now.
The master mechanic told me to vapor lock was not possible because I had no carb, but I seem to remember that my '83 fuel injects 280ZX turbo had a special cooler fan to cool down the injectors in the event of vapor lock after the car shut down so I'm pretty sure this is possible with injectors. I mean, the explanation for that fan was so that if the remaining fuel in the injectors would get so hot after car shut down that it would vaporize the fuel and the pressure would lock up the injectors.
We have a 93 Grand marquis. For a while now sometimes when you take the key out of the ignition the alarm still goes off as if the key was still in it, but it's not. A couple of days ago that happened so I jiggled the ignition to get it to turn off the alarm. When we got back in the car I couldn't get the key all the way in the ignition, I had to keep moving the switch back and forth,finally I got it lined up and could start the car. We took it to the mechanic and he said it needs a cylinder and key. I asked if we could still use our key he said no but maybe. I said ok, can you get us a new key if we need it? He said no. I don't really need any of this nonsense so I was wondering, the ignition switch is working ok now, it just needs to be lined up at a certain spot to get the key out. I really can't afford the 200 dollars right now to fix it.
View 19 RepliesI own a Vw Phaeton 3.0 TDI 2004. A few days ago , everytime i take the ignition key of the car , the car 'dies' ( headlights , radio , doors , alarm... ) and it stops working for a couple of minutes. When i put the key again , the car starts working and everything works 100% but if i remove the key again , the car dies again. The car runs fine if i ride it a whole day , no problems at all. The following day , the car dies again. What's wrong with it?
View 24 RepliesI have an '87 Celica and it takes a good 10 seconds of cranking to start. After being parked only 24 hours, it's the same thing. It won't even give a hint of a kick until about the 8 second mark. Then it'll give a couple of sputters and eventually fire right up. Is this the fuel pressure regulator that's the problem? Is it not keeping the fuel at the rail pressurized properly when sitting? It's just annoying having to sit there cranking for so long to get going. I would think if it was the pump, it would give me problems when running.
View 5 RepliesI'm Using Maruti Suzuki Swift Dzire. Till last month my car used to unlock doors automatically while taking the key out. Now the problem is :After turning off the ignition & taking the key off Car doors are not unlocking automatically. If doors are unlocked manually from inside by pressing unlock button situated in the car, doors are unlocking. If I unlock the doors manually and open the doors, I'm unable to lock the car with the remote key after closing the doors.
View 3 RepliesNew post for a better problem. It was a hot day today in vegas, but my santa fe was running at normal temp (I double checked with my analyzer), running great. When I got home I turned the key off and took it out of the ignition, all the electrics went out (lights, gauges, etc.) yet the car was still running. It took about 5 seconds or so for it to wind down and stop.
2001 Santa Fe, 2.7ltr, 120,000 mi., 2 wheel drive, great shape, no codes.
My problem is with a 2000 Mountaineer V8. Once a year I have to replace the battery after the first cold snap due to low cranking amps. I can simply hook up a battery charger and it will crank and fire. My second problem is most likely related. When I replace the battery it will kick off like a brand new car with no hesitation. After a few starts it takes 5-15 seconds for the engine to fire while the engine cranks normally, and that's how it operates all year. After having this problem again this year (I've owned it 4 years) I've realized the underlying problem is not the battery. All the connections are good, and it has a good ground. No lights or warnings, and when tested with a handheld scanner there are no error codes.
View 11 RepliesOn the wifes Santa Fe 2.4 AWD every few starts it seems to crank over longer than it should. It will usually crank right up like it is supposed to. Every few times it may take 3-4 seconds of cranking before it will fire.
The car runs great, averages over 30mpg per the computer. No codes. I don't have a clue what it could be.
I've had a 1999 explorer for a few months. The transmission has always taken a couple of seconds to "catch" in drive and was then fine. Today, I had to tow another car a short distance and now going into drive directly is useless.
I must shift into 2nd and then back into drive. Then, for the most part, the car drives fine unless I have to put it in Park or in Reverse. Then I must repeat the procedure.
The fluid is fresh and the dipstick shows a slight overfill. Is there anything I can do about this or is this the death of the transmission. If I can run it another couple of years, I'd be satisfied.
I have honda civic 2005 Lx with 170,000 miles. I noticed increased RPM about 1.5 with cold start but no missfire. I attempted to take out ignition coils to see if genuine ones solve the issue. It is very little rainy today with high humidity. After I put new ignition coils, I noticed increased shaking with misfire. I have not touched anything except for putting in/out coils. I ensured the position and connection of the coils. Is this anything with humidity? I did it really quick without much exposure to the rain. How to resolve this issue? at least return to previous condition?
View 7 Replies1991 4x4 f250 idi w e4od w 3:55 ratio... The truck is slow to engage in reverse, about 5-10 sec. It also has a very hard shift 1-2. All other shift points are good. Drop down is good, and TC lock up happens at all the right points (feels like anyway).
I've had the truck for about 2 years now, replaced several sensors an harnesses and a full fluid change to solve other problems but this still remains.
Sometimes when I start it in the morning if I let it sit and idle for a few min it will engage reverse much quicker AND shifts way smoother and constant. Shifts smoothly thro all gears, holding a constant 1800-2000 rpms with no drop or lug. Or do I need a rebuild?
Need better understanding of the wiring and turn signal selector than I do in my 07 6.0 HD. At first the issue started with the right front and right mirror blinking fast indicating a burnt out rear right turn signal. However after a few seconds the right rear will start working and the speed would be normal. I noticed it worse on very wet days making me think the rear tail light was letting in water and messing with the bulb. But it turns out it does it on nice days too.
These days it has evolved into the turn signal sometimes taking a few seconds before any of the right side actually starts to flash, also sometimes the indicator does not automatically deactivate after a right turn.
Giving the bottom of the steering column a calibrated tap usually always fixes the issue until the next turn.
Assuming its a bad turn signal selector switch Part number YL3T-13K359-ABJAEA but not knowing the wiring diagram I dont see how this bad switch would intermittently stop controlling the right rear turn signal. I would guess that it would tell the flasher left or right, not which lefts and which rights.
I have now replaced hpop, injectors, cups, gpr, batteries, uvch on both sides, icp and ipr on my 2002 F550 and it still has a long crank to start.
It has been driven about 1,000 miles since then and no change. I have no codes except buzz test produced a high to low 1272 1274 1276 1278 one time. Cannot get that to happen again.
It is taking 4 seconds of cranking to start consistently hot or cold. It always starts but cranks for what seems like too long compared to my other 7.3s. I have included a screenshot of the data and am curious on what everyone's thoughts are as I am out of things to look at!
My vehicle has 113 k and when I start it cold there is a whining sound for about 20 seconds and then increases in pitch and then slowly winds down to a stop. Does not do it when motor is warm. What it might be?
View 1 RepliesI have a problem that my Treg makes a terrible grinding noise when starting in the morning. It sounds almost like a bad bearing or something. It lasts anywhere from 3 to 8 seconds.
View 5 RepliesOn start up (Engine cold) my rpm goes to 1200 for about 30 seconds then settles to 650, is this normal ?
View 10 RepliesWe love our Treg, but I am not happy about the clatter (like not lube for a second or two) when starting in the morning. Temps are warm this time of year. Otherwise, everything OK.
View 1 Replies