Passat (B6) :: Rough Idle When In Drive / Slight Loss Of Power With Horrible Gas Mileage
Feb 20, 2013
My 07 2.0T (101k mi.) Passat idles roughly when in the drive position (at a stop light, or sign, etc.), the engine sounds "gruffy", and suffers from a slight loss of power with horrible gas milage. I've had spark plugs and the coil pack replaced two weeks ago, and still can't seem to find the source. There are no misfire codes or any others showing up. From reading many posts here, I've found that a common issue is carbon build up for similar symptoms of my car. Do I need fuel injector cleaner, and or valve stem cleaner, etc? As far as the possibility of cleaning out the intake valve, I only open the hood to add oil, washer fluid, check my oil, and wipe down the engine.
View 5 Replies
Advertisement
I have a 2001 VW Passat Wagon 1.8t AUG. A couple of months ago, I took it into my shop for a check engine light. The did the following work on the vehicle:
Replaced MAF sensor
Replaced broken oil level sensor
Replaced outer CV boots
Resealed my transmission pan (it was leaking)
Replaced bad vacuum hoses
When I got the car back, it was idling really rough, and one time it even stalled. Just after starting it, when I hit the gas it wouldn't respond immediately and sputtered for a little while. Once I got going it was usually OK, unless I was going uphill...where it wouldn't perform as well and the engine noise kinda wavered. I also noticed that my gas mileage wasn't nearly as good as it used to be. (I never experienced any problems like this before they did this work) So I took it back to the shop and they replaced both the front and rear 02 sensors. I still had the same problem, so I took it back, and they replaced the fuel filter. Still has the same problem.
The light came on after a month, so I took it back and it was the random cylinder misfire code...and they said that didn't really know what to do about it. So I decided to take matters into my own hands. I cleaned the MAF sensor they installed (took it out and sprayed it with cleaner) nothing. I replaced the spark plugs and while doing so found that one of my ignition coils was bad, and I replaced that as well. Turns out the AutoLite plugs that a local parts store sold me are crap for this engine (actually caused misfires) so I went and got Denso double platinum plugs the next day and put those in. And finally I changed my air filter. Still having problems.
View 5 Replies
My daughter has a 1993 maxima SE (3.0 DOHC) that ran ok until one day when she left work and started the car it was running very rough (missing and sputtering). She had the car towed here and I looked it over,it had a lot of visible problems which I have fixed (cracked coil packs,leaking valve cover gaskets, filthy fuel filter,clogged pcv valve, oil saturated air filter,spark plugs burned down to nubs etc, I replaced all those obviously defective parts) but the car still idles very rough, idles too low RPMs (400-500 rpms), exhaust smells like raw fuel and it only gets 5 miles to the gallon on my last test drive.
I removed the intake manifold to get to the rear fuel injectors to see if they might be stuck open and leaking.The car had been sitting for about 5 days with the battery disconnected and when I removed the first injector there was no fuel in the injector or the rail and no pressure in the rail.I left the injector out overnight and the next morning there was fuel all over the top of the engine and in the fuel rail.I put the injector back in and unbolted the rail,I reconnected the battery and turned the key to start the fuel pump.I waited for about 3-4 minutes and did not see any fuel leaking from the injectors.I turned the key off and removed it from the ignition,disconnected the battery and bolted the fuel rail back down.I again removed one of the injectors and there was no fuel in the injector or the rail and no pressure in the rail.After about 2 minutes, with the key out of the ignition and the battery disconnected,I saw fuel start filling the rail and the injector port, so I quickly put the injector back in.
I`m thinking the next step would be to replace the fuel pressure regulator and recheck the injectors for leaks.Am I on the right track here with the pressure regulator? What could be causing the car to suddenly start acting this way, my daughter said the car ran fine on her way to work ( although I hardly think it could have been running "fine" with cracked coil packs,clogged air filter,worn plugs etc)...
View 13 Replies
I have a misfire in the 6 cylinder on my 98 Chevy c1500 5.7l 350 v8 2wd. I changed the spark plugs and wires, cap and rotor, and changed the spider injector i put the spider injector in from another engine I had. After doing all this the code still comes up. The truck runs fine and except it idles slight rough not bad at all and now it says I have a vacuum leak and while I'm driving you can feel the loss of power. I tried all the ways to do it like on YouTube. What is wrong with my truck?
View 10 Replies
I have a 2004 Ford F250 with 174,000 miles the truck has a slight miss a rough idle one hot or pulling I have 2 codes nut no light when I go into the ford oem feature in my scanner a PO 272 and a PO404 .. Where to start?
View 4 Replies
2004 1.8T, 44,XXX miles, Tip. So I left work today. As I was pulling into a turn lane, very slowly, and coming to a very gradual stop (maybe 10 MPH) the car felt very slightly rough. it wasnt even very noticible, but seeing as I notice every little thing, I picked up on it. It felt like the road was maybe a bit bumpy, but I wasnt sure. The Tachometer was at maybe 800-900 RPM, not really out of the ordinary, but something seemed odd.
So, just as soon as I thought "Well, at least the CEL isn't on", the CEL comes on, blinks 3 or 4 times and goes out. Other than what seemed to be a slight "roughness" for a few seconds, the car felt and ran as good as ever. CEL stayed out. I came home, then went to Autozone to see if i could get it scanned, but they were totally useless.
So - if the CEL went out, would a code still be stored? I know blinking is bad, but it went out after a few blinks. It didnt even stay solid, just went out. There was no message on the display screen either (no "Stop Car" or "Emissions Workshop" etc) First time this has happened. I read on PW that it could be the ICM. I'm hoping it's just a random anomaly.
View 6 Replies
My7.3 is idling rough till I pull the fuse for the fuel pump them it will smoothen out I ran a by pass switch to us my truck but the fuel mileage is bad why
View 13 Replies
Car is an automatic 1.8T and has a rough idle when the car is in DRIVE and I am in a full stop. Car also idles rough when in park. Not sure if it is an idle valve stabilizer, or a coilpack? Car does drive well once in motion and does not feel like it lacks power.
View 9 Replies
Dad has a 01 one ton with the 7.3 and isn't real tech savvy so I'm posting for him. He is the original owner and has been complaining recently about the lack of power. Particularly the upper end. He is having to downshift way more often and where he used to not have to. And we've both noticed a very noticeable shake at idle. Not a vibration but a true shake. He changes the oil every 5000 on the dot and I've gone and changed the air and fuel filter and ran hose and see foam and royal purple injector cleaner through it with no results. Truck is all stock with 225000 on it.
View 7 Replies
I have a 2002 F-250 7.3, 159k on it. I bought it in March, ran AWESOME up till now. I was driving to work last week, check engine light came on, truck lost power and started idling rough. I have a buddy who works for a Ford dealer as a diesel mechanic, he came over with his scanner and laptop. #2,#4,#8 cylinders kept coming up saying possible problems are injectors, harness, rings.. He also did an electrical check, that all checked out. He told me to get injectors, so I got 4 injectors (yes I got the correct #8 injector), valve cover gasket, injector harness and 4 glow plugs.
The parts came last Friday, we did the job and it ran great. Drove it Friday night, Saturday, Sunday morning, no issues. Sunday afternoon we were on our way to a birthday party, truck started doing the exact same thing... Check engine light, rough idle, loss of power. After I got home from the party, my buddy came back over, put it on the scanner again, getting the same codes again. Deleted the codes, ran the tests again, same codes, deleted the codes, rant the tests again, same codes.
He said he is going to come by tomorrow with the box to check each individual cylinder.
View 14 Replies
I was driving my 2011 the other day home from work and experienced a rough idle. Normally the truck idles pretty smooth. I noticed when I was driving at highway speeds the truck seems to shake a lot. I pulled over and turned the truck off. I did a walk around and could find anything out of the ordinary. I started it back up and no more rough idle. However while i was driving at freeway speeds I could feel a momentary lack of power, then the truck would regain its speed. This would only last a sec or two.
I figured I'd give it a few days.... well now its gotten worse. Its doing the same thing but a noticeable difference in the lack of power. I still have boost pressure and the turbo seems to working fine. Im trying to figure out what it might be. I'll be taking my truck into ford again...
View 12 Replies
Ever since I took my 18" wheels off for the winter and put the stock VW 16's with snow tires I have on multiple occasions almost rear ended the car in front of me when I experienced what seemed like a loss of brake pressure. The brake pedal did not feel spongy or anything but often in this situation the abs brakes seem to kick in for no reason. I feel a slight pulsation in the brake pedal which I can only assume is an activation of abs. I'm wondering if this slight pulsation (1 second duration ) is causing my brakes to be less effective. The pavement has been completely dry and I was not traveling fast enough, nor pressing the brakes hard enough to cause the tires to lock and trip the abs.
View 4 Replies
SAAB 2007 9-3 - Recently my car has been having a rough idle and stalling on start up. It has been getting worse and I need it fixed ASAP for a long trip coming up. I cannot have this thing die on me while I'm 300 miles from home....
At stop lights the car will have a rough idle while in park and reverse. While in neutral, nothing. As soon as I accelerate, it goes away but does have a lack of power if I really push the pedal. Once I am in 3rd/4th gear, the car feels normal with no issues. If I am on the highway and slow down then need to accelerate, it goes back to losing power BUT if I change over to manual and downshift, car gains power and goes back to normal.
Here's what I have done so far:
1. Changed the spark plugs twice. Once with cheap ones, the second time with expensive ones. I also swapped out the boots.
2. Cleaned the MAP sensor
3. Cleaned intake sensor
4. Replaced air filter
5. Changed oil
6 New battery
The engines gives no codes whatsoever and I have taken it to a couple places and their readers don't see any codes. My SAAB has a built in fuel filter and this cannot be replaced unless you replaced the whole pump (to my understanding). I plan on buying some Seafoam today and see if that works. Also, I have been told to clean my air intake valve but I cannot get the damn tube off! I feel that if I yank and pull on it, it's going to damage the tube. I am not seeing any obvious leaks anywhere. One thing that is weird about my car, since I have bought it used a few years ago, my headlights/tail lights/blinkers go bad QUICKLY!
View 1 Replies
I have a 00 Accent with 132k miles, I replaced the motor a year ago with a correct 2000 Hyundai 1.5 with 50k miles. I replaced everything that I could at the time, timing belt , starter, water pump, and clutch. It has been running fantastic getting 40 miles per gallon with zero problems , However in the last week I have noticed a rough idle that seems to miss with a vibration that it didn't have before. I have a noticeable loss of power and torque. My miles per gallon has also dropped to about 25 mpg. My check engine light is not on. I will check the plugs and change the air filter today but I would like to know what else could be causing the problem as I am not really sure what to check.
View 9 Replies
my f150 running right so i can enjoy it like everyone else does. I have a 2005 Ford f150 with a 5.4 auto.
It has a rough idle(shakes the truck), very little power, and poor gas mileage. Randomly It will throw a code for misfire on 1 and/or 3 on start up only. It does seem to perform better within the first few of starting but dies right off after that. In fact i got stuck in the snow the other day and it could barely break the tires loose to try and get it out (almost put in 4low cause i didn't want to hurt the trans). I have replaced:
Cats
Fuel pump
Plugs (motorcraft)
Random Coils
Did the timing chains and phasers
MAF
All new injectors
Intake gasket
Was at my mechanics and had a scanner on it and at idle the 1-4 cylinders are all show a negative cylinder contribution. But when you rev it up they all go to 0 across the board. Was kind of thinking about the Variable Timing solenoid.
View 1 Replies
Explorer with 4.0 has a rough idle, just put new plugs & wires, air filter looks good. i did get a new fuel filter as well but haven't gotten to that yet. It has 102k. I have read some info about motor mounts could come lose casing the motor move a little more, not sure about that one. its the wife's haven't driven or looked into it yet, its on the to do list weekend. She also informed that it seems to lose power a little while driving sometimes, thinking possible fuel pump now?
View 4 Replies
I have a 2005 F-150XLT with the Triton 5.4L. The other day while driving on side roads (Paved, not back roads) I noticed my CEL on and it was blinking. There was a very rough idle as well as a big loss of power. When I pressed the gas pedal it was sluggish to say the least. I have yet to get a computer on it, since I had to order one. There is also a light gas smell, only smells near the rear of the truck. From what I am guessing, I think it is either a spark plur or a coil over pack, Truck has about 56K on it.
View 1 Replies
My wife has a stock 03 Passat 1.8t.
1. The car seems to shift too soon from 2nd to 3rd and i can hear the turbo drop pressure. It sounds like a quiet blow off 3 or 4 times when it shifts from 2nd to 3rd.
2. There is a vacuum control valve that sits on top of the air cleaner box and it ticks a lot. it has a electric plug going to it.
3. The car has a rough idle while in drive and sometimes shifts hard. I changed plugs, trans flush and filter change.
I would take the car to a VW dealer but the closest one is about a hour away and my wife needs the car.
View 1 Replies
Last night, I left it running while unloading a trailer and come back to notice it was idling abnormal. I jumped in it and tried to move it and there was a noticeable loss of power. I unhooked the trailer and tried to get it home. I only made it 1/2 mile down the road when it started spitting and sputtering (surging ever now and then) to a level that it died completely. I was able to start it back and get it out of the road but had to be pulled into a drive. It got to a point it wouldn't start back at all.
Today it started up however still had a rough idle and really has no power to speak of. The more I messed with it the less power it seem to have.
I have searched the forums and tried these things:
1) Checked the oil and noticed it was on the low end of the operating range. I put some in it to put it back to normal.
2) Disconnected the ICP
3) Changed the crankshaft position sensor
4) I dumped the fuel bowl after it completely died (in case it had any water in the fuel bowl).
The fuel filter was just changed 2 weeks ago. The fuel pump seems to be operating correctly (or it at least refilled the bowl) and started again with a very rough idle.
It doesn't have a engine light on nor do I have anything to read any codes it may be showing.
View 14 Replies
What would cause my truck to have a long turnover start, a really rough idle, and a loss of power after idling at a stop light for about a minute?
This problem gets worse as the truck warms up. It feels as if I'm not getting power from all 6 cylinders but this goes away after about 20 feet of acceleration. The truck has never not started. It just has to turn over for about 5 to 10 seconds before it fires up. I changed the spark plugs and wires thinking it was that and then i tried the fuel filter and it wasn't that either.
View 8 Replies
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
View 4 Replies
