So I was replacing the lights with the new leds change one toke some pics to compare. Everything fine...
Removed the other feston put the new led and they won't turn on anymore..
Change them back. Put them upside down, up, sideways... Nothing
Check all three fuse boxes all ok
Every other light on, inside trunk on, side markers on...
Everything but the license plate lights.
One of my license plate lights doesn't turn on until I tap it..
What could be causing this? I installed LED's in them but a few months later I noticed this happening.
Was installing led license plate lights and they turned on for a second then shut off, I began trying to switch them around and do whatever I could but still wouldn't light up even put the stock ones in again and they wouldn't work.
View 8 RepliesSo I bought LED license plate lights, the same ones Track5tar has (who sent me the link to get them). I got em off the bay, and I put them in and they don't work! The Heatsink gets hot but the lights don't light up in both of them!
View 24 RepliesBulbs are fine, I turned the light switch from off to on (12 o'clock position) and they flicker for a split second. What can be wrong? I checked the harness on the rear hatch and it looks fine. Maybe the switch itself?
View 2 RepliesFor a few weeks now I noticed my stock license plate bulbs started to act strange. My left one is about half burned out, and the right one started to flicker and burned out entirely.
So.. Easy fix right? I bought 4-smd led lights to replace the burnt out ones and as soon as I installed them they worked perfectly! But about twenty minutes later .. The right one burned out. And the left one is dim.
Is there something wrong with the wire? what can I do?
I have a Ford Windstar 1999 . My license plate lights are both out. I remove the inside panel of the back door, there is a connector between the license lamps and the rest of the car electrical system. I disconnect it. I go turn on the lamps at the dash board, I then reconnect the connector to the license plate lamps at the rear door… and they work! I go back to the dash and switch the lamps (controls side +rear lamps and license) OFF and then immediately back ON, and the license plate lamps stay OUT. All the others lamps on the fuse circuit work fine. When lamps are lit, shaking the wiring harness has no effect. What is happening and where? This is very strange!
View 4 RepliesI have a 90 Honda Accord and can't figure out why the lights aren't working. I have no computer codes and all the fuses are good. The headlights, brake, turn signal lights, hazards and interior lights work fine but the tail lights, license plate lights, and all marker lights won't go on. I only noticed by a chance walk around on the car. I've checked every fuse inside and outside fuse panels. The hazards and brake lights going on makes me think that it can't be a ground problem.
I have spent a lot of time trying different things and checking wires andd fuses and can't find any problems. Is there a relay or something for the marker lights?
Where the license plate lights get thir power from? I have a 2002 SC430 and the plug is just dangling. It goes behind the plate and then if I look under the car, it is just there by the bumper and I cannot find a connector that it can reach.
View 3 RepliesI try to install LEDS on it and I guess I accidently blew the fuse and when I try to search for it, I can't locate it.
View 3 RepliesMy Pathfinder has the license palate in the middle/center of the hatchback door, with one light on the left and one on the right. I cannot figure out how to change the bulbs and my manual is no dice; it shows the process for a different location of the plate on the door, maybe a different version of my year model.
View 6 RepliesI am planning on adding fog lights to my Corolla 2011 LE.
I am considering this one ....
and these LEDs for my license plate ....
So my tail lights and license plate lights are not working. The head lights work also my gauge cluster lights are not working. Which fuse I should check. Or what it might be?
View 6 RepliesHow do I get rid of license plate holes on my front bumper? I took my front plate off and now I am stuck with annoying holes drilled into my front bumper. Its not noticeable but i know its there so it irritates me.
View 4 RepliesI was just washing my 2016 superduty that just turned 3000mi and noticed the light housings and plastic are broken on the license plate lights. The one just fell apart in my hand. 55k and this happens at 3000mi.
View 9 RepliesNo tail, turn, backup, flasher, license plate - NOTHING. i checked fuses - cleaned both connectors under the truck by drivers door, cleaned connectors by the spare tire (2) one large one and one small round, the cleaned ground lug on top of spare tire bracket, all bulbs are new. cleaned with LPS contact cleaner, they were new and shiny and reinstalled. NOW - turn is very weak and when i push on brake they go off and the front blinkers blink twice as fast? I a aircraft technician and know my way with an ohm meter but totally stumped.
View 8 RepliesI'm having some sort of electrical malfunction on the back of my Mk4 Gti. The right rear tail light, license plate light and back windshield wiper doesn't work. I replaced the bulbs several times and they keep blowing.
View 2 RepliesHow to change license plate bulbs? The little clear covers dont seem to pop off ........
View 3 RepliesWas trying to remove the licenses plate screws today. One comes out easily, the other won't budge. I've sprayed a couple of times with WD40 but its still stuck.
View 14 RepliesSo I took my GTI in for my 10k service and to have them fix the wastegate rattle and the subframe shifting. They fixed the wastegate by installing the clip but didn't have the shims in stock for the subframe so I need to go back anyway, but I'd really like to fix my license plate lights before then.
Is there a possibility the tech could have accidentally unplugged a cable for the lights when he was rotating the tires or messing with the wastegate, etc? Maybe a blown fuse? I'm running LEDs and I already tried putting the incandescent bulbs back in but they don't work either.
Mounting front license plate somewhere other than the "official" mounting location? I don't like the thought of putting holes in my front bumper. I can move it down a bit such that the holes are in the bumper just above the air opening. So, they would be less noticeable. This would block some of the airflow through the lower opening. But, unless I'm driving in 100+ deg temps, it probably won't matter.
I could also offset it to the right or left in the lower opening.