Passat (B6) :: Idling Is Little Rough - 3 Codes P0011 / P2293 And P000A
Nov 23, 2010
Only thing I've noticed is the idling is a little rough but the car has 88k on it so that's expected. I haven't checked the cam follower yet and know I'll probably need to change it so that's going to happen in the next week.
I had a code for P000A & P2293 for a few months that would throw a MIL and I would reset it and it would come back after a while. I finally replaced the cam sensor and I didn't see a MIlL for about 6 weeks and one day it came back. Once I scanned the car it showed P000A again. I cleared the code and everything seemed fine until yesterday. I went to start the car and the car wouldn't turn over.
I pulled the key out and tried it again and it worked. More and more I think about it, the car doesn't turn over smoothly over the past few months but maybe I'm just looking for things. I ended up scanning it last night and it had a code for P2293 & P0011. I cleared them both but what could be causing all this and cannot afford to bring the car in to the mechanic. It's out of warranty and I'm broke and X-Mas is around the corner.
2006 Passat 2.0T
View 2 Replies
Advertisement
My 05 Passat, 1.8t keeps showing p0010. The cam tensioner and camshaft sensor have both been replaced, the oil pressure is correct but it keeps showing the codes with the CEL on.
View 1 Replies
I now have a p0011 code on my 2001 passat 1.8t aug. this is a thinker because right before the test drive around the block i did the following
- coolant flush
-replaced the fuel filter
-cleaned the knn air filter
-rotated the tires
-oil change with new castrol 5w-40 syn. and 1/2 a bottle of lucas syn oil stabilizer.
With a few phone calls a possible cause is the timing chain skipped a tooth cause of the lucas being to thick, other cause could be the tensioner finally went out?
Right know the car car has a rough idle and seems to be finding idle , and a noise from the engine around 4000 rpm.
I am waiting for the engine to cool off before i open her up to check timing.. if the chain is off a a tooth what could be the cause?
View 4 Replies
I have a 2010 coroola "S" and the ABS and Brake light have come on recently and it seems to drive fine. I have read the codes and the are : P000A and P050B
View 4 Replies
I've got an '03 Explorer with the 4.0L SOHC that I got for a deal on craigslist as it needed timing chain tensioners. I got that all done and it runs and drives relatively well, but it idles a little bit rough - especially when it's sitting in gear at a stop light. My go-to first attempt for idling issues is to squirt off the MAF sensor, throttle body, and squirt some starter fluid around the vacuum lines to check for vacuum leaks (though it's possible I may have missed a line or two). Neither seemed to work much. I cleared the codes, dumped some Sea Foam and fresh fuel in it and drove it around a little bit and it threw the CEL light, got about 10 mpg, and generally just didn't seem to have as much power as it should (though I have no experience with the 4.0 in a explorer, soI'm not counting that as a hard fact).
I pulled the codes and I've got a:
P2196 (O2 sensor stuck rich - bank 1 sensor 1)
(and)
P0174 (system too lean - bank 2)
That seems kinda weird to me. Bank 1 is rich and bank 2 is lean? That would make it idle and run weird, for sure, but I'm having a bit of a hard time figuring out what would cause that. I think my next step would be to check/replace the plugs, but that's more of a shot in the dark than a proper diagnosis.
View 14 Replies
ODB2 Code: P0300 - Multiple Miss-fire
I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.
So here are some basic info pieces:
1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.
There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.
View 7 Replies
Show 2 error P0011 and P0014.
Sonata YF 2010 2.0 80.000kms ....
View 1 Replies
Well my car is listed above it has 99 k on it now.. For the last few months the check engine light had been coming on and off.. It usually happened after I put gas so I figured it was the gas cap... Till yesterday I had it scanned at auto zone and gave me the code listed above... Don't know how to go about it.. I've searched some and found that it could be a cam sensor of some sort or a follower ( spelling) ... Is it a easy fix .. Like I said light goes off and on.. Doesn't stay on always.
View 13 Replies
I have a 2003 20th ann. GTI, it shut off on me on my way to work. It would turn on but only for a sec and turn back off. I turned it on and tried to move it over out the way of traffic and wouldnt move and turn back off. Got the check engine light checked and the codes P1007 which is coolant temp sensor and P0011 which is camshaft sensor. I replaced both and problem not solved car will start but wont go and turns back off, black smoke and a strong smell of gas comes out the exhaust.
View 3 Replies
Throwing codes here.... been seeing the P1347 consistently with the P0011 and P1143 intermittent.
I have checked the resistance of the camshaft adjustment valve resistance and found them to both be around 9 Ohm (spec is 10-18 Ohm).
I checked the voltage to both camshaft position sensors and they are in spec at 4.9 Volts
I swapped the camshaft position sensors to see if the code would follow the sensor but it did not so it is directly related to the intake camshaft.
It is looking like there is a timing issue either related to the adjustment valves going or possibly some contamination preventing them from working properly. They are both out of spec in terms of resistance which is odd that they would both go at the same time but possible.
The oil inside the camshaft position sensors is no good I cleaned it all out when I swapped the sensors but no change. These will have to be replaced.
Car has 125k on it so it could be due for timing chains but I want to rule out anything else first.
View 6 Replies
I recently bought a 08 Sonata V6, with 94K mileage. The oil pressure light comes on when the engine is idle (around 700-800 rpm). The seller told me that this problem started a few months ago, but the car has not been used much since then. He also said that he has changed the oil after that, but the problem still persists.
The engine light has shown up more recently, like in a week or two. I took the car to a mechanic and he could not guess what the problem might be. But he gave me the error codes: P0011, and P0051. There are no other obvious symptoms (e.g. oil leakage, low oil level, unusual sound from the engine).
I could not find any thread regarding both of these issues (Oil Pressure, and the error codes) together. Any connection between these two?
So far, I have realized that the oil pressure can be due to a bad sensor, and P0011 has something to do with CVVT, and Oil Control Valve (OCV). But I would like to make sure I don't just waste money by replacing the sensor and OCV.
View 2 Replies
My car is throwing this p2293 code which means fuel pressure regulator performance 1 had towed twice this week my mechanic replace the fuel pump in the tank but yesterday I died again with the same symptom ...
View 6 Replies
Last week my wife's passat started idling a little off and then the check engine came on. So I connected my scanner to the car (not VAG-COM) and the two codes that were stored were P2015 and P2008. From what I can find online it has something to do with the flapper motor but the description of each code is:
P2015 - Intake manifold runner position
P2008 - Intake manifold runner control circuit
View 2 Replies
Alright, so I was driving along and everything was fine, I had no error lights and the car was running perfectly. I accidentally went over a lip of this parking lot a little too fast and all of a sudden the check engine light came on!!! I took it to Jiffy Lube and the codes I got were : c1253, c1311, p0011, and p0012. Is my car safe to drive tomarrow? Are these super expensive to fix? Could they have been set off from the curb?
View 2 Replies
Just noticed the other day the Passat was idling significantly rougher than usual, most of the time it's smooth as butter but not so much lately. It's not rough like a bad misfire, just not very smooth anymore. This could be indicative of the dreaded oil-pump bolt failure rearing it's ugly head (finally)?
View 1 Replies
I have an 08 Passat 2.0T with 44k on it, just did the 40k service around 42k. This past Friday I filled up from almost completely empty, and later that day and ever since the engine has been idling rough and the CEL came on. Gas cap has been checked already.
Should I wait to go to the Stealership until I've burned this tank of gas out? Is there anything else I can do that you can think of?
View 8 Replies
I just got my first dub, and it is a project car. I have had it serviced and it still idles rough when in drive with foot on the brake but idles normal when in park. a
View 2 Replies
I haven't started my passat for the winter and I finally did today. It was ruff start/idling and I pretty sure it was misfiring on one of the cylinders. I turned off the car and start it again...same thing, ruff idling like 3 cylinders were running. I waited five 5 mins and started it again, then it was a normal start on all cylinders. But the engine light came on, even though it started properly. I know I have to clear the code to get rid of the engine light. But I want to avoid any future misfiring. So I'm thinking new spark plug/coil overs.
View 9 Replies
Weird problem on my Passat today. First the engine light came on...followed by rough idling. It smooths out when moving, but rough again when stopped. Noticed that turning ON the AC makes it a little smoother...but when you turn off the AC, resumes the rough idle.
Already made an appt with the dealer tomorrow...but wanted to see if this problem is familiar to other owners. Either way, I will update once the dealer finishes diagnosing the problem.
The car has been perfect up to 30k miles...now 2 problems in the last month.
View 1 Replies
Ok, I have owned my 02 Passat with the 30V 2.8L V6 since may. I got it with 115K and now its just under 129K I had the timing belt done at Jimmy's in Provo UT at 126K and up until then the engine ran great. Since the belt was replaced <along with the water pump and such> . The car has a tendency to feel like its idling rough, and when you start it up first thing on a cold morning it sounds like the valves are rattling. It does this for a brief second then goes away until the next time you start it in the cold morning. It wont do this if its warm outside, or after you start it previously that day. So far I have replaced the plugs with Bosch Platinum 2 prong plugs, and replaced the fuel pump. I replaced the fuel pump when it dead on me without warning about 2 months ago.
View 1 Replies
I bought a 1999(b5) passat, 1.8t(AEB) 5spd, came with a DIRTY K&N so i cleaned it with the cleaning kit....
Car drove fine, then: started it up after an hour or so.. it was idling rough, then would spike(17-1800), idle rough, idle fine, spike....etc. just random. it went away for a few minutes, so i tried to drive it home... got 1/8 mile into 3rd... and car just bogged down so i slowed to stop and turn, went to go, it was idling rough so i couldnt drive, just "hobble" into parking lot.... i let run, more random rough, spike, fine... so i let it sit, off. when i returned, it was the same, but now CEL light on...
Codes: P0103 - Mass or Volume air flow sensor circuit high input
P0134 - Heated Oxygen sensor - bank 1 sensor 1 (H02s11) sensor circuit no activity detected
View 2 Replies
