Passat (B6) :: How To Remove DRL
Feb 15, 2011
Without vagcom?
View 8 RepliesWithout vagcom?
View 8 RepliesHow to remove the air vents?? Center along with Drivers/passanger side. Bentley shows to use a trim tool/wedge and looks like they just pop out.
View 1 RepliesI wanted to know how to remove the shift knob from the 1.8t and yes its a 5 speed!..
View 2 RepliesRemoved the trnk emblem from passer sedan? I'm looking to spray it....
View 17 RepliesI have to remove the outside door handle in order to make a repair on the door. I did remove the torx screw from the side of the door but still doesnt come out.
View 3 RepliesI have a 2004 1.8T 4Motion (automatic) that blew a CV joint boot. After inspection of the other side, I decided to replace both (just the outer boots). Got the axles out without much trouble but now I cannot drive the joints from the axles. I've tried both and neither is cooperating, I've knocked out off them with a mallet but they aren't budging. Is there something to do besides just driving them off?
Axles are tubes (hollow) p/n's 8D0 407 271 (& 272) ED.
My cup holder sticks and will not come out like it should. I believe me brother had spilled some coke on accident. How to remove it. Or maybe give me a "how to" link they know about. I tried searching for this but, I could not find anything. I have a 2000 passat.
View 2 RepliesFirst of all... do I need to remove both, the restraining bolt AND nut to remove the tie rod end... if yes, than this bolt seized, the nut is easy but even if I punch the bolt it wont move... ??
View 4 RepliesRemove or replace the tail lights on a B6 wagon? I'm changing mine out tomorrow with the new smoked tail lights and was wondering if there's anything I should know ahead of time. Or even a step by step order to removing them.
View 4 RepliesLooking to wrap the dash trim the piece across the dash and the trim around the information display. Any tips? Also for the console.
View 3 RepliesHow to remove clamp around hose? I am in process of changing out reservior tank. Ignore post. I got it, was afraid they were the one-time use only type of clamps. But duh, they are the spring clamps.
View 1 RepliesThinking of cleaning up the engine bay of my Passat 3.6 V6. How to remove the engine cover of a Passat 3.6 V6? For asian cars, it is fairly straightforward.
View 2 RepliesI need to remove the front headlight in order to repair it. Must I remove the bumper? How?
View 16 RepliesI am looking to remove the entire cruise control system from my passat. Where the cruise control module is and what the cruise control module connects to? i know it needs a signal from the VSS, but what else?
View 2 RepliesHow to remove hood release and plastic trim from driver side covering wires going along driver door, left rear door and to the trunk? I am trying to install subwoofer and amplifier in the trunk need to fish wire through the car from battery to a trunk, and got staked with hood release (opener), i can't remove it and piece of plastic where you put your feet holding together. I don't want to brake anything.
View 2 RepliesMy son spilled some milk in the back seat yesterday and the smell is horrible.. I need to clean up under the seat. I don't know how to remove the back seat.
I have been trying to remove the back seat but it has 2 locking clicks; one one each side than I can not unlock. The clicks on front were easy to pop but this one on the side does not.
Car: 02 Passat GLX 4motion V6 AWD
I'm in process of replacing the rear strut and I can't remove the way bar link bolt out. It is really tight into the inner rubber and it won't buzz. The bolt sits in a way that I can't use a hammer.
On my 2014 passat I figured out how to remove my inner lights on the trunk part but I can not remove the outers. How to get these off?
View 3 RepliesI want to have my oil cap sit close to the valve cover rather then have that long funnel.
I want to go from this:
To this:
I'm in process of changing my interior trim, had removed already all trim from dashboard etc. but can't figure out how remove trim around gear gaiter, trim with ESP and Autohold. Pulled really hard, nothing happens, don't want to break it.
View 1 RepliesI'm doing an install on my son's 2000 passat V6 30 valve.
I have the front rad pulled out and there is plenty of room to work. How do I get off the viscous fan assembly. I removed the fan's 3-4 allen bolts, I now need to get the assembly out. I also removed one of the long allen bolts in the actual assembly. I have the fan ribbed pulley secured with an old serp belt and grip wrench. I am trying to losen the large nut behind he fan assembly. I have attached a photo to point of reference. I may have a manual next week yhat may explain all this.