Passat (B6) :: HIDs Go Out When Using High Beam
Feb 14, 2009
I installed an aftermarket HID's on my 06 B6 2.0T, used VAG-COM to disabled DRL's. They work great no issue, expect when I use my high beam.....both HID's go out and I get warning light/message on the dash. I can get them to come back on by turning the lights off and back on.
View 7 Replies
Advertisement
Car is a 2002 b5.5 1.8t sedan.
Bought the DDM Tuning HIDs, 3500k 35w for the fogs, installed with no problems. Also ordered the 5000k 35w for the low beams. Installed them, they flickered on for a second, then nothing. Let the ballasts charge for a while but still nothing. Called DDM, they said my car needs a error code eliminator kit thing later they were at my doorstep. Plugged one side in, flicked on then nothing. Thought both sides might need the code eliminators plugged in...wrong. both flickered on, and then nothing. Tried again, no flicker, both low beam fuses burned. Plugged the regular bulbs in, changed the fuses, lights working again.
I don't know much about electrical, but DDM said i def don't need a relay kit. Do I need a relay kit? Or would putting higher amperage fuses in the place of the original ones work? if so what amperage?
View 7 Replies
This morning a dash light informed me a headlight bulb was out. It was my DTR light on the passenger side.
I purchased Sylvania H7 high intensity, installed it and it failed to work properly. Daytime light on only drivers side works.
High Beam on , both lights works.
I checked my manual and it said to check fuse in the 5 slot on the driver side dash/door panel and there actually is no fuse in there. I checked the driver side and there was no fuse there either.
I replaced my driver side bulb last year and it took 5 mins....i am already 4 hours into this!
View 4 Replies
i just recently put in 35W 8000K hi/lo HID's in my GLI the problem is for some reason on my instrument cluster it says my hi beams are one which they are not and it is only lightly illuminated. if u turn on the hi beams the hi beam switch on the cluster turns on and gets brighter so is their any way i could have the switch completely turned off like it was with stock bulbs?
View 1 Replies
I have an MY10 R36 wagon, and just looking to upgrade the High Beam only for night time driving.
View 1 Replies
My right sided high beam stopped working and my dash "bulb" warning light is on. Low beams working normally and still swivel around on startup and when turning. Is there actually a separate bulb for the high beams? I ask because when you flick on the high beams I hear mechanical movement inside the headlight housing, making me think high beams may be just a redirecting of the light. Having computer issues so haven't tried VAGcom yet. Also haven't checked fuses...
View 9 Replies
Any tips for replacing the passenger side high beam? I can get my hand in there by there is no way to turn the bulb. Any easy tool to grip and turn the bulb?
View 5 Replies
My high beam doesnt work. I have a Euro Passat with H7. I bought new H7 yesterday but still no luck.
I have switched fuses to new ones.
Is there anything else I can check?
Is there relays on this model for the high beams?
Low beams works fine and everything else in lights.
View 4 Replies
My car is fully stock, with all options available to me (cold weather package not available here). The low-beam triple-LED headlights are aimed way too low compared to all my previous cars, and where they should be. BUT high-beam is aimed properly. So if I adjust the low-beams up, my high-beams might end up lighting up the trees, not the road.
If adjust the headlights up on a fully stock car (not lowered at the front)? Are the high beams still lighting up the road fine? And if you can be specific as the number of turns on the screwdriver, it'd be good too to have an initial adjustment reference.
View 3 Replies
I drive a 96 Subaru Legacy. What does it mean when one of the high beams is dimmer (less light output) than the low beam? I am using a brand-new bulb. It's not an adjustment issue because I was looking at the bulb when it was outside of the housing and it clearly gets dimmer when you switch to brights. However, they are equally bright when on low-beam, so I don't think its just a crossed wire.
View 2 Replies
How do you activate the parking lights with the blinker/high beam stalk. It has the P....
View 7 Replies
So, last night I go to turn on the high beams on my 2002 Passat (pushing the bar on the left of the steering column forward) ... and nothing happens. The bar clicks into place as it should, but no high beams. The little indicator light on the dashboard does not come on, either.
I try to flash my high beams, and that DOES work. The brights come on, and the little indicator lights up when the beams engage.
So ... I know it's not a fuse, since the lights are actually functioning. What part/switch/relay/whatever needs to be replaced to get this fixed? I feel like this would involve me needing to pull apart the mechanism in the steering column, but I hope not ...
View 3 Replies
I replaced the low beam and high beam on my Subaru, now the low beam is very dim and the high beam doesn't work. Careful not to touch the bulb.
View 3 Replies
I have a 2012 Hyundai Accent GLS and recently noticed that my low beam only works in the high beam setting and the high beam doesn't work.
View 10 Replies
Ok so I installed HIDs in my stock housing, I no longer have high beams since I bought the low beam ones only and I think since there is nothing running to where the high beam wire on the oem harness my high beam light on the cluster is stuck on no matter if its on low beams or high beams and its causing my Fogs to not work.
View 7 Replies
When I use the high beams on my GTI with LP, the pattern goes very high with an oval/round top. The road is lit up fine, but I've never seen a pattern go up so high. Is this normal or a problem.
View 15 Replies
My sister said her headlights were dull. So when she came over it looks like both HID's are out?
Since I have only owned pre Mk5 cars I know NOTHING about HID's. So why would they BOTH go out?
View 6 Replies
I have a 06 passat and I installed a kit, and it keeps flickering, any reason why this would happen... My drls have been disabled, and i thought that should clear the problem.. it hasnt..
View 7 Replies
My DDM HIDs came in the mail today and fellow vortexer D.Passat00 was kind enough to meet up with me and do the needed vag-com adjustments. So firstly a shout out to him, he's a solid dude and really nice
Now: Is there a DIY for headlight removal? I can't seem to find one, and without removing the headlights I'm afraid there just isn't enough room to install the new HID bulbs without dinging/touching them.
I have a 2010 2.0t Passat and I got the 35w 6000k DDM HID kit
View 6 Replies
I installed some aftermarket HID lights in my 08 passat. I took it to a local shop to have the drls turned off and the bi xenon turned on. All the warnings and bulb out lights went off, the lights fire up perfect. but for some reason now the lights (all of them, rear, dash, parking all come on with the ignition whether or not the lights are switched on or off.
I am sure a code got changed that causes that, but which code would activate all lights all the time? It's not DRls it all lights are on just like you turned the lights on manually.
View 2 Replies
I have a 2012 gti with oem bi-xenon head lights. What code or setting do you use on vagcom to bring on the fog lights when I turn on highbeam?
View 3 Replies