Last week my wife's passat started idling a little off and then the check engine came on. So I connected my scanner to the car (not VAG-COM) and the two codes that were stored were P2015 and P2008. From what I can find online it has something to do with the flapper motor but the description of each code is:
P2015 - Intake manifold runner position
P2008 - Intake manifold runner control circuit
Check engine light on, these are the codes, can't find anywhere? Seems to run fine. '07 fsi V-8.
View 3 RepliesOnly thing I've noticed is the idling is a little rough but the car has 88k on it so that's expected. I haven't checked the cam follower yet and know I'll probably need to change it so that's going to happen in the next week.
I had a code for P000A & P2293 for a few months that would throw a MIL and I would reset it and it would come back after a while. I finally replaced the cam sensor and I didn't see a MIlL for about 6 weeks and one day it came back. Once I scanned the car it showed P000A again. I cleared the code and everything seemed fine until yesterday. I went to start the car and the car wouldn't turn over.
I pulled the key out and tried it again and it worked. More and more I think about it, the car doesn't turn over smoothly over the past few months but maybe I'm just looking for things. I ended up scanning it last night and it had a code for P2293 & P0011. I cleared them both but what could be causing all this and cannot afford to bring the car in to the mechanic. It's out of warranty and I'm broke and X-Mas is around the corner.
2006 Passat 2.0T
My gf's 04 gti 1.8t 5spd is having idling issues. Here's the rundown, at idle it sits at 800 rpm but when given a rev it then becomes erratic and fluctuates between 500-1100 rpm. When throttled again lightly it returns to normal 800 rpm idle. The car will try to stall a little bit. Now for the codes and lights. The lights are the traction control light and the check engine light. The codes are p0102 (MAF) and p2181 (coolant system performance). I have recently had a misfire which I took care of with 4 new coil packs. I kept the 3 good ones I took out. I have to change the plugs still but don't think it's an issue. Has new clutch and sits at 148,852 miles.
View 5 RepliesThe car is a 1994 volvo 960, it has a rough idle, and its idling high (1500 rpm and higher) its throwing 7 codes, we just replaced the O2 sensor, we reset the computer, and still have issues, (though its no longer running rich!!!)
Here are the codes
1-1-3 injector group 1
1-1-5 injector group 2
2-1-2 O2 signal
2-3-2 long term fuel trip idle
2-1-4 rpm signal
3-1-4 cmp signal
2-3-3 long term ilde air trim
We also checked the idle control valve points 1-2 read 15 ohms and specs say 10-14, for the harness side port 1 read battery voltage (12.3) and port 2 initially read 10.2 then we wiggled and played with the injector wiring harness and it read 11.8.
We also poured fuel system cleaner right into the fuel filter and started it up, and just dumped the rest in the tank
I'm heading out to check those other sensors but what else could be causing these issues, also the temp gauge is reading cold all the time, but the fan kicks on when the car gets warm.
My husband has a 2011 GTI, which has just hit the 40k mileage mark. His CEL started coming on in March, but we figured it was due to him not tightening the gas cap enough, as he'd open and relock the gas cap, and the CEL would go away within a few restarts of the car. Took it into the stealership last week, got the 40k service (which was a bit of a rip-off in itself), and then got told the manifold was bad.
This is the exact text for the invoice: "Checked the vehicle for codes and found code P2015. Traced the intermittent failure to the intake manifold valve flap sensor failing."
I've seen a lot of posts around this problem, for many models and years, but it seems like most people managed to get it repaired under warranty / TSB. So I have three questions:
1. In the OBD codes, does it store date as well as code? In other words, is there a way to prove that this failed under 36k miles?
2. What's the process for getting this escalated to VWOA customer care, since I feel this should be taken care of under warranty?
3. The dealership we took the car to (which is not where we purchased the car, but is just closer to home) was shady, and the guy we worked with was, to say it nicely, a jerk.
Soild CEL, autozone pulled a P2015 code, but couldnt find it for VW in their system, just hyundai, toyota, dodge, and kia codes came up.
Looked around and everywhere says it's the notorious MKVI IM replacement issue.. Im under PT warranty until Nov. '15 so im good there.
Heres the catch.. sometimes it goes off without any changes to the vehicle. First thing (before the obd2 reader from autozone) i checked was my gas cap, that will cause a CEL sometimes, next time I started the car the CEL was off. the next day, without touching the gas cap since, the CEL was on again, today its off
car idles fine, drives fine, MPG are fine, pulls fine, stops fine, steers fine, everything works in the car. year: 2011
I've got an '03 Explorer with the 4.0L SOHC that I got for a deal on craigslist as it needed timing chain tensioners. I got that all done and it runs and drives relatively well, but it idles a little bit rough - especially when it's sitting in gear at a stop light. My go-to first attempt for idling issues is to squirt off the MAF sensor, throttle body, and squirt some starter fluid around the vacuum lines to check for vacuum leaks (though it's possible I may have missed a line or two). Neither seemed to work much. I cleared the codes, dumped some Sea Foam and fresh fuel in it and drove it around a little bit and it threw the CEL light, got about 10 mpg, and generally just didn't seem to have as much power as it should (though I have no experience with the 4.0 in a explorer, soI'm not counting that as a hard fact).
I pulled the codes and I've got a:
P2196 (O2 sensor stuck rich - bank 1 sensor 1)
(and)
P0174 (system too lean - bank 2)
That seems kinda weird to me. Bank 1 is rich and bank 2 is lean? That would make it idle and run weird, for sure, but I'm having a bit of a hard time figuring out what would cause that. I think my next step would be to check/replace the plugs, but that's more of a shot in the dark than a proper diagnosis.
I have a 2000 Ls 3.9 V8 125,000 miles that started idling rough.I checked for codes and got p0171 (bank 1 lean), p0175 (bank 2 rich) and p0307(cylinder 7 misfire). I swapped cop and sparkplug from cylinder 7 to cylinder 5 and erased the codes.I ran the engine for a while and rechecked the codes to see if the misfire followed the cop and plug. They did not. I still get p0171,p0175 and p0307 (cylinder 7 misfire).
View 7 RepliesMY gc started cutting out a few weeks ago while idling in gear. I changed out the four plugs I could get the wires off. It's a v6. It started running better for a couple of days. I need to know of any way to get the stuck boot off. I also have a feeling there is something else wrong. Anything else that might be causing it to cut out. It has progressed to cutting out while going down the highway.
View 4 RepliesCar started idling funny and stalling. Finally wouldn't start. Changed crusty spark plugs, started up once, then stalled and wont start again. Checked for spark, no spark. Changed crust dist cap and rotor and ignition coil and still no spark. Checked ignitor activity and appears to be working.
What else is there? There's a little doofer next to the coil that looks like it has two wires come out of it, looks magnetic (has metal shavings on it, probably from old rotor)... Could the ignition switch be the problem? It cranks, but no spark.
I have a 1997 volvo 850 that has started intermittently stalling. It usually happens when i'm idling, like at a stop sign or traffic light, but recently it did it on the freeway. I have taken it 6 times to the mechanic (5 times to one and finally having learned my lesson the last time to a new one) and they say it is one of 4 things, but can't figure out which of those 4 things it is until it stalls on them. which it hasn't done. it acts perfectly when at the mechanic's and then they always give it back to me, only for it to happen again. the last time the car ran beautifully for 6 weeks before stalling out on me again....... oh, and once they replaced my fuel pump which seemed to work for a while.
View 2 Replies2002 santafe 4x4 v6. about week earlier I had a cel for temp sensor voltage high. so I replaced it. then... my power steering cooling loop by radiator started to leak from corrosion and for some reason my coolant gauge was reading about a needle with from the red. (maybe from getting ps fluid on it? idk) so I went to investigate why it was leaking and I thought the cooling loop pluged into a cooler on radiator so I removed my lower front engine mound and motor mount by the timing belt so I could raise engine up a2" to get a better look. when I saw it was just a loop and that was my leak I ordered replacement. It came in I swapped it out. Pretty easy . Decided to do a radiator flush and replace thermostat. Why I was at it. I drained radiator and took the old thermostat out. was gonna leave it out for the flush to cycle better. When I started it up it was idling around 4k rpms. I figured it might be because of thermostat so I put the new one in.
Started it up and same thing.... I check all the vac lines I could find all were tight. I unplugged them one at a time at throttle body/intake tube and blocked it off with my finger and it was still idling high. It also started surging. going from 2k to 4k and going back and forth. I checked the maf and it was clean as a whistle. No leaks on intake pipe. If I put my hand over maf it sucks the tube towards the throttle body. no air leaks anywhere. Took off iac valve its clean. I plugged the holes where it is on tb and started it up and no change in what its doing. also the throttle body flap is closed the hole time. Iac seems to be properly opening and closing. when I watched it after I unbolted it. I sprayed brake cleaner all over manifold to check for air leaks no change in high idle. I also took off the evap valve hose to tb and plugged it at tbody and no success.
I checked my sensor connectors and there tight and no wires are pulled out. I have yet to check cam sensor connection. (does it have a cam sensor?) I unplugged battery over night. this morning it ran at 2k rpm for two mins then surged to 4k. could it be my throttle position sensor? is there a way I can check with multi meter? Ive done a lot of research and it seems like a common problem with Hyundai but people don't leave a what fixed it post after they figure it out. they just leave the threads hanging. I hope I can figure this out.
When I get home tonight Ill plug where the brake booster vac line goes in. I looked at the hose and it was super tight and didn't seem to be leaking but maybe booster is idk. Ill also check wires to all 02 sensors. but if o2 sensor wire was broke wouldn't it throw a cel? Also no check engine light. but id did have an abs light come on the other day. was thinking maybe an abs sensor at the wheel but I am not sure. That light was on for a week before this issue started. It was never revving up until I started working on the other issues from my research I am guessing throttle position sensor. I am going to multimeter it tonight.
I have a 2004 Cadillac it started to miss when your idling, a check engine light when on and it was #5 plug not firing so I changed the plugs in front 4 of them and also bought a coil pack and replaced that, but it still misses. What else can I check before thinking its a sticky Valve or internal engine problems.
View 6 RepliesMazda CX-7 sport that has rough idling when it is started and goes away when warmed up or driven. Is giving OBDII error code P0300 - multiple misfires. Where should I start looking?
View 3 RepliesHad a P2015 code today on my 2009 Tiguan. Does this mean I have to replace the entire manifold ?
View 6 RepliesODB2 Code: P0300 - Multiple Miss-fire
I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.
So here are some basic info pieces:
1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.
There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.
My 2004 F-150 Heritage with the 4.6 was running great until yesterday. Went in the store and left it idling, when I came back out it had died. First time it has ever done this. I started it and it started right up but misses bad. Checked it out and found all 4 cylinders on the drivers side are dead. The check engine light is on and the overdrive off light on the shifter is on. It will start right up and everything else is fine, oil pressure, coolant, etc.
View 9 RepliesI have been a check engine light on and off for the past few months. I finally got the codes read and I have P2015, Intake Manifold Runner Position Sensor/Switch Circuit Range/Performance Bank 1, and P0303 Cylinder 3 misfire.
The car had 80,000 miles, APR intake, Downpipe, Exhaust, and tune. When I had this work done I had engine problems and replaced the spark plugs and Upgraded Coil packs from the R8. Two years later and I get these error codes.
I got the known p2015 code about a month ago and the CEL is on. Here is my situation though...I went and had my car tuned for an APR stage 1+ tune with stock hardware, everything was fine. I then upgraded to a catless 3 inch downpipe (ebay on that links up to the stock downpipe) and a short ram intake and decided to go to the 2+ to delete the engine code for not having a cat.
While I was there, the guy tuning my car said on top of the code for not having a cat, there was a code for my intake manifold saying that one of the motors for a flap wasn't working correctly. I left there expecting to see a code but it never came back on. After4-5 months, I had to pass emissions. Obviously you cant pass with the 2+(found that out the hard way) so I had to have it returned to a regular stage 1 with the stock downpipe. Still no sign of a code for the intake manifold.
I passed emissions and then put my downpipe back on, however, I decided to buy the 200 cell cat from 42DD to weld into my downpipe to save me from having to constantly get my car tuned just to pass emissions. After welding in the cat, I still had a CEL. I went to advance auto and it said I had a code p2015 Intake Manifold Runner Sen Sw Ckit Rng/Perf B1.
I went and got my car tuned to the stage 2 for the hi flow cat and the light is still on. My question is, do I need to replace the whole intake manifold or is there a possibility that I could replace just a sensor? I have a 2012. If just replacing the intake manifold will solve this issue, I'll probably just buy [URL] .... and replace it myself (assumable that's what I need ).
I have a 2001 Santa Fe that I am getting road ready for my son, The engine has recently started idling very high, 2500 RPM at startup. I disconnected the IAC servo and it drops right down to about 900 RPM. I replaced the IAC with a brand new one and it does the same thing at startup, 2500+ RPM. Checked vacuum hoses / tubes. I replaced 2 crack / dry vacuum hoses. Same problem for a while, then idle went down to about 1250. Started to drive it, test ride. while accelerating, seems OK as soon as I take my foot off of the gas, idle goes to 2500 - 3000 RPM until I apply brakes and then it drops back down to 1000 or so. (SOUNDS LIKE A VACUUM LEAK PROBLEM. I CANT FIND IT, IVE BEEN THROUGH 2 CANS OF CARB CLEANER AND HOURS OF REPLACING ALL VACUUM HOSES.)
View 2 Replies