Passat (B6) :: CEL Code P0430 Catalytic Converter Related
May 27, 2013
It came on 2-3 miles after a cold start. 3.6 with 137,000 miles. What's next? First car I've owned that uses very little oil between oil changes.
View 1 RepliesIt came on 2-3 miles after a cold start. 3.6 with 137,000 miles. What's next? First car I've owned that uses very little oil between oil changes.
View 1 RepliesSo the code reads "warm up catalytic converter efficiency below threshold (bank1)" ?? What it could be?
View 12 RepliesThe vehicle is a 2001.5 Passat 4 Motion V6. 120,000 miles on the Passat.
The original Cats were replaced 1 month ago after a service station deemed them dead. When the vehicle failed emissions.
The codes were p0430 and P0420 and P411.
Before that about a year ago The O2 sensors were replaced.
After 2 new catalytic converters were installed. The vehicle is still throwing p0420 and p0430 codes.
My 2000 Nissan Maxima has a PO430 code for the catalytic converter that has been going on and off for over 1 year now. My ? is, how would I know that the converter needs replacing? Someone said there wouldn't be any smell necessarily, someone else said I would be leaking qts. of oil in between changes and someone else said it would get bad mileage. Each one debunks the others comments etc. Also just for info., this car had the ses light come on at 57K miles, my brother replaced 2 of the O2 sensors and I replaced 2 also, one duplicate one and a mass air flow as well.
View 1 RepliesDoes this mean the DPF is shot? I believe its integral with the cat. whats worth checking first?
View 2 Replies1996 4runner here (187,500miles), with weld in after market cat (on when purchased, with less than 1000 mile on it). started throwing the 420 code beginning of last summer. Replaced both O2 sensors and same results. Was coming on after every 30-40 miles after resetting, replaced wires, plugs, cleaned throttle body started coming on ever 120 miles or so. Now in the middle of winter it has gone 450 miles and still has not come back on?? Does the winter fuel blends in Georgia, or cold more dense air make a difference on cat performance? Still plan to replace it with a direct fit with a warranty but curious if I am overlooking something.
View 6 RepliesTitle says it. Cat is done. Threw code p0420 and am experiencing hesitation at WOT. Already replaced my front o2 (cbfa) and now I'm debating whether or not to get a new downpipe. I daily the car and am wondering if keeping the car as is for a while will damage anything. Cts turbo has a sale for a catless downpipe.
View 5 RepliesThat Car Grand AM 2000 2.4L SE
The current problem with the car is that it is not accelerating fast, for example i would push the petal to the metal and only go 25 mph and my RPM would be 3000-4000. Initial my brother and cousin though it was the Catalytic converter because it was getting hot but that has recently been change along with the fuel filter and spark plugs. but the catalytic converter is still gets red hot so i forbid myself from driving it till i fix what every causing the slow acceleration and the temperature of the Cata when i took the error code think P0300 random misfire to the local Autozone they printed me a long list of things that could be a issue my question is what is the likely culprit so i can fix those 1st before shelling out cash to rebuild a engine. may just have to get rid of it at that point. so i guess what am asking is a list maybe top 10 so i can fix them one by one as my money comes in.
Before the accelerating issue the car would randomly stop when i slowed down or stooped that when i replace the spark plugs.
2004 Chrysler Sebring Sedan, 4 cylinder dual-overhead cam. My check engine light came on this morning and the code came out as the catalytic converter. The car seems to be running fine, at least no recent changes. I'm debating replacing this vehicle soon, and I'm wondering if it's worth working on the catalytic converter. I recently replaced the cam shaft position sensor as well.
View 5 RepliesI checked out a 2006 Prius yesterday a guy is selling. It had the CEL on (not sure why somebody would try and sell a car with that, but anyway). He said that it's because they get gas at a station that consistently doesn't tighten the gas cap enough but by the time the tank is down to 1-2 bars the light always goes away. Although I don't doubt his story, I absolutely doubted the cause. So I took it to get the code pulled and it was P0420, which is catalytic converter threshold below efficiency.
View 15 RepliesI recently had my catalytic converter replaced with a non-OEM cat. The check engine light came on and a different shop (different from the shop that replaced the cat) said that it will keep coming on because I had the cat replaced with a non-OEM cat.
View 3 RepliesMy 2000 Forester has 96,000 miles on it. A few months ago, the CEL came on. At first it would turn off every couple of days but would eventually pop back on. I first thought it was tied to putting gas in the car, now I think it was just a coincidence.
Over the past two months, I have replaced the catalytic converter with a aftermarket piece (done by a mom and pop muffler shop) and replaced the front o2 sensor three times. The first two times, I used Bosch sensors from an auto parts store and had the code cleared. After about 50 miles the CEL came back on. Just yesterday, I picked my car up from the dealership where they installed a Subaru fron o2. After about 30 miles, the light is back on again. Code is P0133 - heated oxygen sensor, bank 1 sensor 1, circuit slow response.
Now, the dealership is suggesting I need to replace the catalytic converter with a Subaru converter before they can source the issue.
2010 f150 with 5.4 catalytic converter. Engine light has been going on and off for the past couple of months. Had the code read and its says bank one catalytic converter. Ford dealer said to replace the 02 sensors. Had that done but light still comes on and off with same code. Could there be something wrong with the sensor or should I just have the CC replaced also. I just don't understand why it would come on for a few days and then not come on for a few days if its the CC?
View 1 RepliesSo this morning (Kind of Cold) I went out site and started my car. I heard some noise under the car and I noticed that the noise bad been coming from the Catalytic Converter area and there was water dripping off of it.
My guess is that it was just warming up and the water was from the cold. Is it normal?
I have a GLX V6 ...
My check engine light has been coming on and off and it seems to show P0420 for catalytic converter. The light stays off for about a week and it'll come on for a day or two and off again.
Wouldn't a failed converter stay failed? Can P0420 be triggered by loose/bad gas caps?
I have a big hole in my catalytic converter and the car sounds like it is missing a muffler. Where I should go to have that hole welded as i do not see myself spending ~700 to get a new one for Passat 2003.
View 24 RepliesI have a 2000 Passat with the 2.8L engine. The flexible pipe which is part of the catalytic converter is leaking and the only way to replace it is to replace the catalytic converter. VW refused to assist with the repairs because the car has 96000 mi on it. Emission warranty is 8/80000. How I can replace only the flexible pipe without the cat. because it's still good.
View 3 RepliesI have some serious work that needs to be done on my car. The catalytic converter needs replacing, and the valve cover gasket and cam adjuster seals need to be replaced. This work falls under their respective warranties. However, I'm wondering if I should have the water pump and timing belt done at the same time as I have 77000+ miles on my car. Is there anything else that would be good to do at the same time as this work. I would be going back to the VW service center for these repairs. Would it save me any money to do this all together?
View 4 Replies2001 V6 Passat with 125k miles throwing a P0430 code.
Having trouble on cold starts, takes about 10 minutes to finally get it to turn over. When it does the idle is extremely rough. For the first 1/4 mile the car bucks, stutters, and misfires. After that it runs fine and starts fine when already warm. I am noticing slightly decreased gas mileage but nothing major.
Valve cover gaskets were replaced 2 months ago, but were leaking oil for at least a year before I could afford to have them replaced. I am still noticing some oil leakage, however not as much as before. I have had both O2 sensors replaced twice in the past 5 years. Timing belt was replaced at 98k. What might be causing the starting issues?
I have recently picked up a 2005 F350 with the 5.4, which has 212k on it. Has a check engine light on for P0420 and P0430, as well as some kind of a 'ignition coil 'D'', I forgot which code it was as I deleted them at first to see which would come back. After driving it, the P0420 and the P0430 came back, but not the other, yet probably. I'm guessing the misfire due to the ignition coil caused the cats to go bad and the 420/430 codes, unless these codes are coincidental and the cats went due to high mileage.
Either way, I'm pretty sure I will need to replace the cats and was wondering what is the cheapest route. Should I get individual cats and have a shop weld them on? Should I go to Advance Auto parts or Auto Zone and get the whole pipe with the cats attached to them already and then get them installed? I anything will involve welding, I would have to bring it in to a shop. Also, in regards to the ignition coil misfire, what a good way to check which one it is?
I bought this truck (2011 F-350 6.2l) used a month ago with 125000 miles on it. Of course the MIL light came on as soon as the ink dried. The codes read PO420 & PO430 and my local Ford Service said replace the cats. I said what is the cause of the failure, ford said here is a list of possible causes but it's not reading other codes so they don't know what caused the failure.
Well, I went ahead and replaced both catalytic converters, all four O2 sensors, and I replaced all sixteen spark plugs. Guess what, the MIL light is back on not 24 hours later reading PO420, PO430, and now PO620 and PO645. So I just went back to Ford today and all they did was cleared the codes and told me to call if the light comes back on. They said my PCM is up to date but why it's now reading GENCOM code or AC Clutch code.