My 05 Passat, 1.8t keeps showing p0010. The cam tensioner and camshaft sensor have both been replaced, the oil pressure is correct but it keeps showing the codes with the CEL on.
View 1 RepliesOnly thing I've noticed is the idling is a little rough but the car has 88k on it so that's expected. I haven't checked the cam follower yet and know I'll probably need to change it so that's going to happen in the next week.
I had a code for P000A & P2293 for a few months that would throw a MIL and I would reset it and it would come back after a while. I finally replaced the cam sensor and I didn't see a MIlL for about 6 weeks and one day it came back. Once I scanned the car it showed P000A again. I cleared the code and everything seemed fine until yesterday. I went to start the car and the car wouldn't turn over.
I pulled the key out and tried it again and it worked. More and more I think about it, the car doesn't turn over smoothly over the past few months but maybe I'm just looking for things. I ended up scanning it last night and it had a code for P2293 & P0011. I cleared them both but what could be causing all this and cannot afford to bring the car in to the mechanic. It's out of warranty and I'm broke and X-Mas is around the corner.
2006 Passat 2.0T
I replaced my headers and added slp loud mouth 2 side exit now my truck is throwing every evap code o2 codes and p0010 & p0020, There is 17 codes total. The headers are obx without cats. Also added 80mm bbk throttle body and some brisk racing plugs with hot street coil packs. Truck run with all of that stuff fine but when i did the headers and cat back everything went wrong.
View 9 RepliesShow 2 error P0011 and P0014.
Sonata YF 2010 2.0 80.000kms ....
I have a 2003 20th ann. GTI, it shut off on me on my way to work. It would turn on but only for a sec and turn back off. I turned it on and tried to move it over out the way of traffic and wouldnt move and turn back off. Got the check engine light checked and the codes P1007 which is coolant temp sensor and P0011 which is camshaft sensor. I replaced both and problem not solved car will start but wont go and turns back off, black smoke and a strong smell of gas comes out the exhaust.
View 3 RepliesThrowing codes here.... been seeing the P1347 consistently with the P0011 and P1143 intermittent.
I have checked the resistance of the camshaft adjustment valve resistance and found them to both be around 9 Ohm (spec is 10-18 Ohm).
I checked the voltage to both camshaft position sensors and they are in spec at 4.9 Volts
I swapped the camshaft position sensors to see if the code would follow the sensor but it did not so it is directly related to the intake camshaft.
It is looking like there is a timing issue either related to the adjustment valves going or possibly some contamination preventing them from working properly. They are both out of spec in terms of resistance which is odd that they would both go at the same time but possible.
The oil inside the camshaft position sensors is no good I cleaned it all out when I swapped the sensors but no change. These will have to be replaced.
Car has 125k on it so it could be due for timing chains but I want to rule out anything else first.
I recently bought a 08 Sonata V6, with 94K mileage. The oil pressure light comes on when the engine is idle (around 700-800 rpm). The seller told me that this problem started a few months ago, but the car has not been used much since then. He also said that he has changed the oil after that, but the problem still persists.
The engine light has shown up more recently, like in a week or two. I took the car to a mechanic and he could not guess what the problem might be. But he gave me the error codes: P0011, and P0051. There are no other obvious symptoms (e.g. oil leakage, low oil level, unusual sound from the engine).
I could not find any thread regarding both of these issues (Oil Pressure, and the error codes) together. Any connection between these two?
So far, I have realized that the oil pressure can be due to a bad sensor, and P0011 has something to do with CVVT, and Oil Control Valve (OCV). But I would like to make sure I don't just waste money by replacing the sensor and OCV.
Alright, so I was driving along and everything was fine, I had no error lights and the car was running perfectly. I accidentally went over a lip of this parking lot a little too fast and all of a sudden the check engine light came on!!! I took it to Jiffy Lube and the codes I got were : c1253, c1311, p0011, and p0012. Is my car safe to drive tomarrow? Are these super expensive to fix? Could they have been set off from the curb?
View 2 Replies2005 GTI 1.8t Engine ... I changed my timing belt water pump and tensioner yesterday and today I am receiving an engine code: P0011 Intake (A) Camshaft Position Timing - Over Advanced (Bank 1) My friend timed the engine and knew that is was 1 tooth advanced. He told me that is was going to be OK because 1.8t's have a 1 tooth tolerance. I would have redone it but I did not know how. What to do in this situation? Do I need to re time the engine?
View 2 RepliesI now have a p0011 code on my 2001 passat 1.8t aug. this is a thinker because right before the test drive around the block i did the following
- coolant flush
-replaced the fuel filter
-cleaned the knn air filter
-rotated the tires
-oil change with new castrol 5w-40 syn. and 1/2 a bottle of lucas syn oil stabilizer.
With a few phone calls a possible cause is the timing chain skipped a tooth cause of the lucas being to thick, other cause could be the tensioner finally went out?
Right know the car car has a rough idle and seems to be finding idle , and a noise from the engine around 4000 rpm.
I am waiting for the engine to cool off before i open her up to check timing.. if the chain is off a a tooth what could be the cause?
I recently sent for a reset my airbag module, yes my car was in a collision, I replaced passenger airbag(only 1 airbag deployed). And reconnected the module. Using the VAG COM, I scanned the airbag module, shows no fault codes, but i still have a light.. now I'm thinking seatbelts and sensors maybe the problem. Where the sensors for a 2005 passat passenger dash airbag are located.
View 2 Replies2002 Passat 1.8T
Backstory. The P0411 code shes had for quite some time. I think probably 4 years maybe. Just never did anything about it because I guess they are expensive to fix. Thats the SAIP and combi valve correct? Anyway to remove all the emissions stuff and get the codes deleted?
So, about 3 weeks ago, maybe a little longer i cleaned her engine bay, replaced a few vacuum lines because the shop she took it to last year did a terrible job. Mind you, they did a head gasket, timing belt and some other minor things while they were in there. And they couldn't take the time you run new vacuum lines, since they just cut the originals and used a bunch of t fittings to "solve" the problem.
Anyway, i replaced the lines and it seemed to run better at idle, still had a little mis at idle but ran smooth at speed. I also did an oil change, put some fuel injector cleaner in it, put some seafoam in the oil, and cleaned the engine bay thoroughly. I did it properly and took all the plastics off, cleaned them, scrubbed the bay and used an air hose to get rid of the excess water. Left in a nice state. Ran smoother, looked better, so on and so forth.
Fast forward to last week, and she mentions to me her car isnt running right. Its sputtering, hesitates, running rough, exhaust is puttering, and it used up a lot of gas. She parked it for a few days, and i came down to look at it. Mind you, i don't have a code reader. So I looked at it blindly thinking it had an ignition issue. Nothing could have changed that quick since i looked at it.
So, today we got one coil(just in case ones bad), and 4 new plugs (Autolite Iridiums). Replaced and gaped the plugs to .030, torqued to 23 ft/lbs and started the car. Seemed to run a bit better, but subsided quickly. I then pulled each coil harness plug to make sure it would misfire on each cylinder and it did. So, new plugs and the coils checked out. Time to get its codes read.
Took it to the Pepboys and the codes it came back with were the P0011, P300, P0301-3. Cleared the codes and they came back nearly immediately. I had the dreaded P0011 code. The misfire codes im guessing were from the coils being pulled on each one, and also due to the P0011. Now i read a lot of threads about the P0011 and how its usually not the camshaft position sensor. However, i pulled the plug on that while the car was running and nothing changed. So i thought it could be the CPS. Changed that out and still nothing.....
just bought an mk4 1.8 jetta and so I love it, however I'm having a couple issues. I've got a cel for code p0010 something about the camshaft position sensor. I changed the sensor with a new one and the problem is still there. I've got pretty much full power but no turbo spool and my boost gauge tops out at 5-6 psi.
View 5 RepliesAutoZone provided this code for my check engine light: P0010.
Definition: Intake camshaft position actuator circuit open
Explanation: ECM has detected a low voltage on the VCT circuit
Probable Cause: 1) Open or short circuit condition on the VCT circuit; 2) failed VCT solenoid
Is there a part I can replace myself that can fix this, or is this a dealer repair?
My check engine light comes and goes on as it pleases. When I check the code it says P0011 for cam timing too advanced. That said, I have 0 symptoms for this code, my car runs great, average 30mpg, smooth idle and shifting. My inspection is coming up and I cant have this light on when I take it in. What to do to diagnose why its on, or how to replace the appropriate part. A ball park price is great too.
Vehicle has 134K miles and is well maintained.
I have a 2007 GLS. Within the past year I had about 4 or 5 difficult starts. Just recently I got a CEL with cod P0011. I replaced the OCV as that is the usual culprit. Within 6 miles of clearing the CEL, I am still getting the same CEL. I am wondering if the problem is either the wiring harness or the Camshaft Position Sensor.
View 1 RepliesIn the last four months, I have been getting intermittent error code P0011 on my 2008 prius. I notice that it comes usually when I am going up/down a major hill or going really fast.
View 2 Replies 2008 Toyota Prius Touring. I got a Check Engine Light while at a drive-thru, and my "Automatic" adapter reports this:
I drove the remaining ~60 miles home without incident, and the engine seems to be running smoothly and I don't notice any loss of power or rough idling or anything along those lines.
Going by the first few Google results, a P0011 error could indicate a few things:
-Incorrect camshaft timing
-Wiring problems (harness/wiring) in intake timing control valve control solenoid system
-Continuous oil flow to VCT piston chamber
-Failed timing valve control solenoid (stuck open)
I've had this car for ~3 years and have always been super careful about regular oil changes and maintenance, including dropping an ungodly amount of money getting the "full 100,000 mile service package" at the dealership ~6 months ago.
Suddenly getting a P0011 error code and Check Engine light on a well-maintained 2008 Prius w/ 112,000 miles.
Check engine light and P0010 code in my Gen III 2010 Prius...
View 2 RepliesI have a 2006 Sonata with an intermittent check engine light. The light will be on for a few days then goes out for a day or two. This pattern has been going on for about 3 months now. A scan tool was used and showed the code P0011. I know this code has to do with the camshaft timing. My question is should the light be going out on its own if there was a problem with the camshaft timing? Does the engine correct itself and then experience the problem again. Is it normal for check engine lights to go on and off with out being manually reset? Could this be a faulty sensor or loose wire causing the light to go on and off? The car has about 75,000 miles, mostly Hwy, and is driven just about everyday.
View 36 RepliesOk not that last part, but I'm working on grandma's 08 Taurus V6, light blue. The first symptom was the check engine light, flagging P0011 camshaft adv timing bank 1. When I popped the hood there was a bad rattling/ticking noise from the valve covers. Upon checking the oil, I found coolant in it and the coolant reservoir empty. I figured it would be the head gasket so I topped off the coolant and started the car. No bubbles from the reservoir and compression check was good.
View 3 Replies