My 2.0T 06 Passat misfires sometimes during cold start after 6-8 hrs of parking. It happens very rarely. I have had the car for 4 years (bought it brand new) and the misfire has happened about 5-6 times. Is this normal? Just wondering if they get logged in the computer system so VW Service can see it? My car has got 47K miles on it.
View 5 RepliesI have a 350 throttle body injection 3/4 ton 87 Sierra with 107K miles that runs great but when I shut it off it won't start again! Starts right up when it's cold but I have to wait about 2 hours before it will start again once its been started. Turns over just fine. I recently replaced the coil but that didn't do the trick. Is there some kind of sensor or switch that could be heating up?
View 4 RepliesOk, to start off. I have a 2010 2.0T CCTA with 23k miles. I recently purchased a HPA Intake Manifold and installed it myself. I was told by HPA that they offer a tune specifically for their manifold. I however, purchase the Maestro suite by Eurodyne with the intention on getting it all tuned myself. I was able to code out the CEL for the flappers no problem. Now my only issue is the cold starts. During the cold start cycle I get misfires and air surge. I ran the fault reader and got the P0300-P0304 (Misfire faults). Obvious thing to check were plugs and packs. So I changed them. No change.
I read in a bunch of threads that these faults as well as air surge are a sign of the PCV Valve. I have a catch can kit on order so I will see if that wotrks. My guess is no. Another thing I think it could be is the N75 valve however, this issue only occurs during the cold start cycle. After the cold start cycle is done I have no issues what so ever. So I ruled out the N75 valve. If it was bad, then it would be bad regardless of how cold/warm the engine was. I have attached a video of the Cold Start.
This 1996 (220KM) car will run fine (perfect)for about ten minutes from cold (I'm talking -5 C)then starts to misfire when warmed up. Difficult to pull away (automatic) from a stop. Sound like its missing on two cylinders. Really chunters.
Installed new plugs, wires, cap, rotor, coil,filter. Don't know what to check next. Car will work at speed but I can feel it missing. Gun it and it will go. Doesn't appear to be a fuel problem.
I've got a 2009 Tiguan with 65k miles on it. A few weeks ago I noticed some issues with running rough during a cold start. I only noticed because the engine would vibrate considerably more than usually for the first few minutes of operation, and would idle at around 1050-1100rpm instead of the usual 750rpm. After warm up, things were fine. Suddenly the issue got bad real fast - wife was out and the MIL light came on, EPC light came on, and the car was running extremely rough. We managed to drive it home (2 miles) doing under 20 the whole time on side streets. Once I hooked it up to my OBD reader, I was seeing cylinder misfire codes on all four cylinders.. P0300, P0301..P0304, all five codes simultaneously.
Since the car was due for an oil change and hit 65k miles recently, I decided to throw new plugs in there to see if that would work. It did, at first.. A day or two it ran completely fine, no rough starts, no misfires, I thought I had solved the problem. The old plugs had some deposits on them and were original, so I thought I was in the clear. Two days later, same thing happened again.. EPC light, barely running and misfires on all four cylinders..
I read up some online and decided to order new ignition coils. Took a few days, but I got four new coils and threw them in. Again, problem solved it seemed. No more EPC light, misfire codes didn't come back and no more rough starts. I drove a good 40 miles with no problems at various speeds, but started noticing some misfires during acceleration (slightly rough acceleration, almost feels like a back and forth rocking motion, very slight). Sure enough, after a cold start I'm seeing the engine run a bit rough again with misfires. This time, only P0304 (misfire on cylinder 4) is thrown, and it only shows up as a "pending code" (engine light flashes for a few moments during start, but does not stay on).
I checked my connections, swapped the plugs and coils in what I thought were cylinders 3 and 4 (closer to the driver side), nothing. I swapped what I think are cylinder 1 and 2 (passenger side) just to be sure, but still nothing. At this point I'm pretty lost. I know enough to be dangerous with a carbureted engine, but am lacking in knowledge when it comes to a fuel injected turbo charged VW engine. It seems to be cylinder 4 misfiring consistently at this point according to the OBD reader.
Also of note.. I had some misfire problems last year, and had my intake manifold replaced as part of a recall (also had carbon deposits removed at the same time). Can a carbon build up occur this fast? Can it be the injectors?
Friend of mine has a 2000 Passat. He has a weird problem. The car will just shut off in the middle of driving and won't start for 1-2 hours.. the ECU was already replaced, along with some sensors.
View 3 RepliesI am not sure if it is the same time every night like clock-work or if it's a set interval after I come home...but here is what happens:
-I come home and I turn off the power to my 2010 Prius after parking.
-I lock the car and I get that loud external "Beep"
-Around 2 to 3 hours later, I hear 4 to 5 beeps in a row from the horn. It sounds just like the beeps that are made when I unlock the car. Just a bunch of them in a row..for no reason
It is really loud and ticking off my neighbors. What would cause this? I have a dealer installed Rockledge security system.
When I start my 1999 1.8 petrol passat it needs some throttle to start, low idle speed, misfires, drop in idle, so boot the throtle full - still no pick up and sits on 1000 rpm busy backfiring away! It started after fitting a new windscreen wiper motor, battery was disconnected but went back ok, all other electrics work and no warning on the dash. Didn't touch anything in the engine bay nor were there any issues before I changed the wiper motor.
View 12 RepliesSo I bought a used 1.8t back in august. My second golf, up from an mkiii and I love it. However, the previous owner installed a CAI and being that he lives in the desert, probably never had any issues taking on water. Fast forward to my problem, got caught in a rainstorm, limped it home with the CEL and the traction lights on. it died like three times trying to get it home, but it still would idle when I parked it.
Now I've used the search feature extensively on this problem, and what I've down so far is to take off the intake and reroute it about six or seven inches from the maf, I've cleaned the filter, maf, pancake pipe, and SMIC with denatured alcohol and those are all currently drying. When I took the IC off, specifically the connection between the pancake and the IC, a good three cups (~30oz/850sillyliters) of water dumped out.
Again, my car still was idling when I parked it. Scanned the CEL and got misfires and maf low air codes. Before I started tearing down the intake I took the coils and plugs out and put my shop lights above the valve cover to generate a little heat, maybe make a lil water evap from the cylinders. I live in a pretty arid climate, IE all the water that fell onto my garage floor was gone in 24 hours. Prolly wishful thinking but whatever.
My plan next is to put everything back together when it's all dry, pour a lil oil down into the cylinders, and crank it while the spark plugs are out. Hopefully any residual water will shoot out, along with the oil/gas, and I can go back to enjoying my life.
Also, the intake is hot. I'm thinking any water that made it past the intercooler would've been steam/vapor and I shouldn't need to remove that? Also it seems like it's in a conformation that would force any residual water to drain either into the cylinders or back into the intercooler, so I really don't see any gains by removing and cleaning it
Its been consistently below freezing around here and when the car is cold, I get a parking brake fault as soon as I turn on the ignition. When I press the button it will usually release the brake, however further presses result is flaky operation, inconsistently flipping between working properly and showing a fault. However, if I can clear the fault, Auto-Hold works fine, and once the car is warmed up, the parking brake works flawlessly.
View 11 RepliesSo I went on a trip with my 7.3 PSD the other weekend. It was a 4 hour drive. After 3 hours of driving with the A/C on, the air temp started getting warmer to the point were it seemed like the A/C wasn't working at all. After reaching our destination we didn't drive the truck much or use the AC for 4 days. On the trip home, the AC worked perfectly for the first 3 hours. Then again, the last hour it started to warm up like the AC wasn't functioning at all.
View 1 RepliesOk so i get off work and i go to my car, its around 6ish and its reading 36 degrees fahrenheit. On start up the car beeps and the parking brake wont disengage...tried pressing the button a couple times but nothing. So i turn it off and start it again...nothing. Then finally turn it off, let it sit till all the interior lights come off. Turn it on and lo and behold it works! At an ambient air temp of 36 degrees, is it possible that rotors and pads are frozen? Also could it be that the cold temperature is freezing the brake lines? Also the car was parked so that the wind was perpendicular to the brakes. So like a T with the long part being the wind!
View 12 RepliesHappened to me twice today, engine wouldn't start, message on MFD was "Parking Brake Fault" and the engine would not start. I read through he owners manual looking for a solution, and the engine finally restarted and I was off on my merry way.
About two hours later, on another errand, this time I started down the road, the engine died, I tried a re-start, got the same "Parking Brake Fault" message and this time the engine would not start. Tow truck is going after the car right now. This leaves me a bit frustrated why a parking brake issue would kill the engine.
2008 Passat Komfort...
Car makes a whining type noise when I start it and turn the wheels to pull out of parking spot. Once car is warmed up, the sounds is gone. Is this the power steering?
View 10 RepliesMy brothers car is a 2000 VW Golf 2.0 that recently started starting rough in the morning, when the motor is cold it will struggle to even turn on and will act like its only running on like 2 or 3 cylinders for a second and most cases stall, he is having to pump the throttle to get it to even stay cranked until it all sudden just starts idling fine and it idles perfect but still acts boggy if you try to rev it right away as its warming up, after about 10 seconds of it idling the motor can be revved perfectly fine and you can turn the car off and it will start back up immediately..
View 1 Replies1991 Regal, 3800 v6.
So here's an interesting observation. When i turn the ignition to ON, I hear no sound nor feel any vibration from the fuel pump. Is there any scenario where a fuel pump fails to prime yet kicks into gear after a start? So, I've got rough idles and misfires on cold starts. Before I start replacing parts my diagnostic plans is as follows:
Remove and inspect spark plugs.
Inspect and test starter coil/distributor (still have to research how to do this)
Test resistance on fuel injectors.
Test pressure drop on fuel rails.
Test compression for possible small head leak.
I'm wondering, if I do have a tiny head leak that is letting in a drip or two of coolant after hours of the engine sitting, will I be able to see this on the gauge doing a compression test? I've never done one before and still need to buy a gauge, but maybe I'm better off just doing the other tests and if they all check out I can be certain it is a minor head leak.
My assumption is that I have a leaking injector; just trying to do things the proper way.
1998 Passat 1.8T Sedan, Manual, 118k miles, new head at ~ 87k due to broken timing belt. (Changed oil approximately 1.5-2k miles ago, no loss of oil evident). No noticeable loss of power. No MIL and no DTCs in storage.
But there does seem to be a bit of exhaust (puff....puff.....puff...) that seems to be coming from under the turbo side of the engine, but it is hard to tell.
Recently - over the last couple of weeks - noticed at start-up in morning, significant amounts of blue smoke from exhaust - eventually subsides to nothing after a couple of minutes. BUT, it only seems to appear when the car is angled with its nose slightly up in the driveway and not with its nose down. Lack of it occurring with its nose down was only tried twice; I may need to check it again.
After reading many posts, I thought it might be:
1) Oil overfill at last change - I noticed that my oil was less than 1/16" above the top bend. I doubted that would be the problem, but I siphoned off the small bit and it is within or just below the bend now (hard to read). It might be the oil since I used the Valvoline full synthetic MaxLife that is VW approved for the first time, but I find that hard to believe since I have been using synthetic for a couple of years now.
2) Oil getting into the combustion chamber via oil in the turbo system. Checked the low spot in the hose just before the throttle body. Seemed virtually dry; that's not the problem.
3) I guess it could still be oil gathering some place due to the failure of the turbo, but power seems quite normal.
4) Problem potentially with the PCV (actually called the breather and bleeder valves) and/or vacuum system being plugged up. After reading all of the posts regarding that I am starting to think (HOPE) that is it and not the turbo. While I do understand that flapper valves that are stuck would create greater pressure which could result in oil being forced into the chamber past the valve seats, I am not sure why the angle of the car while parked would matter since the higher pressure would only be occurring while driving; and the blue smoke goes away after driving and doesn't appear until next morning. But perhaps I am missing something.
Particularly which valves I should check/clean if I am seeing this smoking exhaust at start-up, but only when the car is parked with the nose up?
5) Sticky valves at the back-side (cabin-side of the engine)?
Since the OY recall, the info in my MFD is resetting itself about every 2 hours (avg mpg, time driven, route, etc). It used to only reset when I did it manually, which is what I prefer. How I can change it so it won't reset itself anymore?
View 5 RepliesI have a 1984 380SL and misfires badly when it is cold. It has to warm-up at least 10 minutes before I am able to drive it. What might be the cause?
View 2 RepliesWe're talking about a 2002 Subaru Forester with only 80,000 miles on it.
This winter, the cold seems to have taken its toll. The fuel economy is bouncing around between 16 and 24 MPG and the car runs a bit roughly. Especially when it's colder (<30 F) there is often a lack of power/RPM when depressing the gas pedal. The problem is worst in city driving, but exists on the highway also. It doesn't go away during my 15-20 minute commute. For a period of a couple weeks, it was even easy to induce misfires (I think that's what they were; quiet pffft pffft pffft sounds during severe lack of power) by fully depressing the gas. But even if you half-depress and hold the pedal steady, the car will accelerate weakly and then sometimes surge forward. Other times it seems to be idling strong and running rich. Now that it's warmer (>40 F) the problem has lessened, but I've also started feeding it 93 octane gas and the car feels rougher than normal.
A year or two ago, I replaced the front oxygen sensor and spark plugs (prior to problem). This winter, I took it to a mechanic who couldn't explain the problem and replaced the spark plug wires.
Based on my reading, it seems like the only other most likely culprit is the manifold air pressure (MAP) sensor that's mounted on the intake manifold. I haven't worked up the effort (and can't find my multimeter) to do an electrical test of the MAP sensor's output itself. I'm also not keen on just buying a $270 part without sound evidence, nor paying for ill-informed guessing by lesser mechanics (than yourselves, of course!). I also have a sneaking suspicion that the automatic transmission could be slipping -- when I drive with 2 adults and two kids in the car up a hill, it seems more underpowered than days of old.
When I turn the knob under the clock counter-clockwise to reset/change the hours, it works fine, when I turn the knob clockwise to change the minutes nothing happens? Do running the VAG-COM instrument cluster output tests might fix it?
View 3 Replies