I have this whistling noise that developed after re installing my stock airbox. Seems to have just started right after installation. Cant seem to pinpoint what is going on. I also had a error code come u p(p0411). 1.8t b5.5 passat ...
View 2 RepliesSo i got a 98 passat sedan used and was told it read a p0411 code. The person at autozone told him it was a cam sensor. The sensor was replaced. I know now from the manual that codes reads for sec. Air injection system , incorrect flow. It could be the vacuum lines. Now lets say it is the vacuum lines. Their is a misfire on cylinders 1-3.
View 4 RepliesI have a 2005 Jetta 1.8t and the thing will not start! The battery is fine, and has been recharged 100%. The fuel pump is pumping. It cranks all day, but just won't start. The only error code i'm getting is a P0411 which I understand is a leak in the vacuum system somewhere.
View 5 RepliesWhenever P0411 triggers for me, it is very late into driving (i.e. like 30 minutes into the freeway type of situation) where the engine has already hit optimal temperature. I've gone 1000 miles after reset before it triggers. Sometimes 200 or so miles, but it never triggers quickly after a reset. I'm unsure if it matters, but the VR6 does have a cold air intake (and I do have the breather hose connected & maf correctly connected). I'm pointing it out because p0411 became an issue about 500 miles after I had installed the cold air intake.
View 6 Repliesthis is the engine code we got when we checked it out
it also says air injection problem...
what's wrong here?
i assume its something with the vaccum lines?
I have a 2002 1.8T with about 75k miles which makes a harsh rhythmic sound at idle after about 30 minutes of driving. If I tap the accelerometer to increase the rpm and release it goes away and is silent. Recently it also seems to be making the same sound when it starts but goes away as soon as I drive. The sound seems to be coming from the front lower right (passenger side).
I have changed the timing belt about 18 months ago (along with the water pump, tensioner, etc. using an ECS tuning kit) and it ran fine (seemed even smoother than before) but it had a small engine oil leak which my mechanic fixed. I think this sound started after he repaired the leak. I've left the car with him for a week and he just called and said it he couldn't figure it out but it could be an oil pressure problem but I have not had any issues with an oil pressure light.
I have had issues with the P0411 code over the same and have replaced both the secondary air pump and the combi valve but the code just reappeared and my mechanic says he has checked the entire system again and can't figure out what is causing the problem. Not sure if the two can be related but just thought I would add that. The car runs fine otherwise and I have always used synthetic and the large oil filter but I am beginning to think this could be a sludge issue (the noise).
For a week now, my car whistle pretty loudly (I can hear it windows closed) when accelerating. After reading about 2.0t problems, I thought it was either a bad DV or PCV. I tried to diagnose if my problem was related to a bad pcv. So I disconnect the tube going from the intake to the pcv and plug the hole on the intake. Then I went for a ride and it whistle like before...so does this test confirm that my pcv isn't my problem?
As of now, I never saw traces of oil around the oil filler cap. When the engine is running, as soon as I press on the accelerator(even lightly), the whistle begin. As soon as I remove my foot, it whistle for a second then it stop. At a stop, if I press on the accelerator, the whistle will begin at only 5500 rpm and up.
No CEL so far related to lost of boost(I had a cel last week and they change fuel sensors and regulator). Also, the car pull pretty constantly but seem less powerful than before.
I took my car to the dealer two days ago. The idle was rough, it stall twice and I had a CEL.. They change two high pressure fuel sensor and now the car run fine.
But now I hear a disturbing whistle sound when accelerating. The sound is audible from inside the car but louder when the window are down. This is my third turbo car and this sound as no comparison to the sweet whistle of my 1.8T for example.
I opened the hood to check if something was loose, in fact the main clamp from the inlet pipe to the engine cover was loose so I remove the engine cover assembly to check if the tech didn't forgot something else. Everything looked fine, I put everything back together and I hearing this annoying whistle again...
I keep throwing a P0411 - Secondary Air Injection System error. My previous pump was seized so I replaced it, and broke a few of the chintzy air hoses in the process. Now, with new pump installed and new air hoses connected, I can go about 5 days before the code comes back on.
So to recap, I have:
Replaced the air pump
Verified the new air pump functions, yepReplaced the air hoses
Verified connection of air hoses at all junctions
Checked the Secondary Air Relay for function
I have not yet checked the solenoid - unsure how to do so.
P0302
P0301
P1545
P1300 X2
I have no clue what is wrong but I have an exhaust leak and when I am accelerating I can hear the loud shhh sound like the turbo is leaking but I still have power like normal.
Alright so my car is popping up 4 codes.
P0411 - Secondary Air Injection System Incorrect Flow Detected
P0300 - Random/Multiple Cylinder Misfire Detected
P0302 - Cylinder 2 Misfire Detected
P0303 - Cylinder 3 Misfire Detected
Vehicle: 1999.5 VW Jetta MK4 2.0L GLS (AEG)
The P0411 code I have had for a while now and I been lacking to fix it. I pretty sure I can get this fixed but it doesn't cause problems so I haven't paid to much attention to it. Anyways, the other day I noticed a puddle of coolant under my car so after checking it out, the water pump was leaking so I bought a new one and replaced the old one. However, during the replacement process I had to remove the timing belt and I accidentally turned the top pulley about 1 notch and didn't notice at the time. After putting everything back on, I turned my car on and the engine sound a bit weak so I ran for about 10 minutes around a couple blocks.
I instantly noticed that the car had no power and it took me a long time to speed up. When I got back, I plugged in my scanner and I only had the same P0411 code and nothing else. After carefully reviewing the camera I had recording during the water pump replacement, I notice I had turned the top pulley a bit so I went ahead and removed the timing belt, readjusted it, and it worked! I was excited that the car was working fine again. Soon after, I headed out to take a drive and noticed after 60MPH the car didn't have much power. The car still accelerates after 60MPH, but extremely slow. As soon as I arrived back home, I plugged in my scanner and that is where I seen the 4 codes. Now my question is what could have caused this? Could I have damaged something when I ran my car with the incorrect timing?
Things I have done so far:
-I checked to see if I left anything unplugged.
-I checked for any vacuum leaks
-I checked my oxygen sensors so see if I was running rich/lean
Things I will do after work today:
-Check the spark plugs
-Check spark plug cable for damage
Just installed a short Ram intake on my 2000 Vw Jetta 1.8t. Had the Intake for about 250 miles and now the check engine light came on. Just pulled the code p0411 secondary air injection system incorrect flow detected. Is this just cause there is more air going through the MAF sensor?
View 11 RepliesSo of course it has to happen 3 weeks after my warranty expires. My CEL comes on and I have it read and the result is P0440. I find out that my wife has a habit of topping off the gas tank and so I am thinking that she has probably ruined the charcoal canister. It is something easy to replace?
I have an 06 limited edition... Yes, she will not be topping off any gas tank anymore.
98 Taurus, 6cyl, 3.0L OHV, 184K miles. Check engine light is on and code reads "P0411 - secondary air injection system - incorrect flow". This is my son's hand me down car and has a rather large exhaust leak that I plan on fixing. Could this code be related ?? I found out that the CEL has been on for quite sometime now and the car is due for emissions testing (state inspection) in October.
View 3 RepliesI got 2001 vw jetta 2.0.. I keep getting check engine light,,when i scan it keep saying P0411 Secondary Air Injection System Incorrect Flow Detected. i replaced new smog air pump, and new egr valve and today i was driving car and i got check engine light, its still same code.
View 4 Replies2004 VR6 24v ... I had another thread about my son's car stalling after driving about 20 miles and then running good again after letting it sit for a couple of hours. Anyway I changed the Crank Position Sensor and I have been driving it work and back the last couple of days so I am starting to relax that the CPS fixed that problem. Won't be positively sure for a while as the problem took a while to occur. So far so good.
While coming to work today the car picked up the P0411 code, secondary air injection system incorrect flow. When I changed the CPS sensor i unbolted a module underneath the car by the oil filter to get better access to the CPS. I did not remove it, just unbolted it so I could push it out of the way about and inch.
After putting it all back together and driving it for several trips with no stalling this P0411 comes on. Is that module I moved the Secondary Air Pump and could I have disturbed something. I will check it when I get home. How critical is that code. I read where it works to warm a cold engine. What effect would there be driving with that code?
I have this error code on my VW 1999 passat 1.8T automatic car. How to resolve it. My friend reset it and CEL went off for few days and now it came back again. How to resolve it??
View 2 RepliesIt happened to passat. Once I hit about 75mph on highway I get a stop engine (oil presser low light). It flashes than goes off once I lower my speed. I checked all fluids are normal. It throws a 12 code an says oil passage blocked, cam positioning sensor, skipped timing chain. These are what the code says could be wrong with it. The car runs fine with no hesitation at idle or normal city driving. I have already flushed the oil with cleaner, and still getting the light.
View 5 RepliesI was able to borrow an OBD-II scanner to read the error code(P1818) currently displayed. I was wondering if the P1818 Error Code is related to a faulty Transmission Control Module (TCM).
View 1 RepliesMy cousin's B5 wagon automatic 1.8T ('00) was shaking and vibrating intermittently. I took it down to Autozone and borrowed an OBD2 scanner. This is what it said (only one code, and the CL was off, although it comes on intermittently):
P0741 - Torque Converter Performance or Stuck Off
The CEL tripped yesterday and this is the code autozone pulled. WHat does it mean.
View 3 Replies