I'm trying to replace the upper control arms on my wifes '00 Passat. I'm having trouble getting the bolt that holds both the upper ball joints to the upright (stearing knuckle, what ever you want to call it) out. I've tried the typical PB blaster, and heat approach. What I can't tell is if that bolt is treaded into part of the upright or not? Is this something I should just be able to punch out with a hammer?
View 5 RepliesThis has manual knobs - NOT CLIMATRONIC. This actually happened months ago, I bought a new bulb, pulled trim piece and it looked like a PITA. It appeared that I would have to remove the radio to pull the climate control module, but I didn't want to bother w that at the moment. I'm sorta hoping that it is like the B5 Passats in that the bulb is just behind one of the knobs and it's accessible by pulling the knob off. I wasn't sure though, so I didn't want to start pulling on stuff till it broke.
View 2 Replieshow to replace the bulbs in a 2010-2013 Toyota Corolla I am finding older Corollas but not 2013. I did tear apart the dash but it look like they are now a self contained unit.
View 3 RepliesI have an 03 Camry LE I4 with about just under 100k miles. Recently, under semi hard braking at highway speeds, the steering wheel will shake quite a bit to the point that I don't feel safe braking hard. I initially thought the brake rotors were warped, but those were replaced less than 2 years ago somewhere around 80k miles. I've taken it to many shops and here are the verdicts they've given me:
1. Rear drums are warped which is the problem (I don't think so...)
2. Control arm bushings need replacement (coming from shop who did brake work before)
3. Ball joints need to be replaced
4. All rotors should be resurfaced
What should I do?
Getting this code. 01309 - Power Steering Control Module (J500) on my 2012 GTI. Does the module need to be reset or does it need to be replaced?
View 2 RepliesWhere about is this filter located? is it the cabin filter in the glovebox?
View 7 RepliesI just bought a used 98 Acura 3.0CL. I've noticed that when the heat is cranked, it doesn't blow hot at all. I did some quick research and came up with two answers thus far; check the antifreeze coolant and that I may need to replace the heater control valve. Am I "warm" on the area?
View 19 RepliesSo... I found a pot-hole the other day and I'll be replacing the oil pan tomorrow. It's on a '00 Passat V6 FWD, any tips/tricks or things I should look out for? Do I have to drop the sub-frame, lift the engine, etc... what's the easiest way to go about this? I'll post pictures of the pan tomorrow, but here's a teaser:
Couldn't get underneath to see it yet, but I'm pretty damn sure there's a big hole. And hoping that's all it damaged.
How the heck do you replace the crank shaft position sensor on a v6 b5?? i know where the sensor is and i can see it from under the car, but the wire that goes to it looks like it disappears under the intake manifold when i traced it back?
View 1 RepliesCan I replace the battery in my 06 Passat myself? I've been told that I must take it in to the dealer to have it done, so they can reprogram the car. Doesn't sound right to me.
View 2 RepliesReplacing the alternator on my wifes 2003 v6 passat. Not a mechanic by any means but I have plenty of time and all the tools for the job.
View 1 RepliesOkay so yesterday I had to replace my battery because it died just when I was trying to leave for work. Got back on the road it everything was fine. Coming home last night I got a CEL, I figured it was my normal p2177 because of my Forge WINTake that I can't seem to find a fix for. I went to clear the code because I have a fulling loaded APR Stage 1 ECU. Now it won't clear. So this morning I attempted to change programs and it won't change. Should I just go have it reflashed?
View 4 RepliesNeed to replace the clutch on my wife's 2001 AWM. Its for her, no mod's, driven daily to work etc. I just want a stock style replacement that will last as long as the original (165k). Should I go with the stock replacement from Sachs or go with one of the Valeo style dual mass conversions? Does my car even have a dual mass? Can the OEM flywheels be resurfaced/turned?
View 1 RepliesSo I bought a pair of the WinPower headlights and I can't find any posts of a How To remove the factory headlights. Looking for a link so I can finally change them out.
View 7 RepliesI have a 2004 Passat and the manual doesn't say anything about how to replace the headlights. I tried searching but the search function is down and there was nothing useful in the diy section or the lighting diy.
View 1 RepliesI was just curious and bored this morning. So I wanted to ask you all what mileage did you replace your timing belt at?
View 24 RepliesJust replaced the steering angle sensor on my Passat. Had a persistent fault that was causing a parking break warning light. I took pictures as I was putting it back together. [URL] .....
View 1 RepliesI went to get my tires rotated and the mechanic noticed that the right outboard CV Joint boot on my passat had a little tear in it, but the grease hadn't leaked all out. I replaced both the outboard and inboard CV Joint Boots. Below is a nice link for DIY step by step write up with great pictures.
[URL] .....
The driver's side low beam lamp on my 2006 3.6L stopped working. I bought an H7 from the dealer, but it did not light up. How hard is it to change the wiring harness, and how much should I expect it to cost for the dealer to replace? A local garage said it'd cost $115 to just run a diagnosis on the wiring.
View 3 RepliesI did it about two years ago following steps on here but i forgot where to hold the engine cover to take it off, it can be broken if done incorrectly so where to grab that cover to pull it off?
View 2 RepliesI think the battery is dead, so I need to replace it.
View 10 Replies