Passat (B5) :: Rough Idle And Noise From Engine Around 4000 RPM - P0011 Code
May 26, 2013
I now have a p0011 code on my 2001 passat 1.8t aug. this is a thinker because right before the test drive around the block i did the following
- coolant flush
-replaced the fuel filter
-cleaned the knn air filter
-rotated the tires
-oil change with new castrol 5w-40 syn. and 1/2 a bottle of lucas syn oil stabilizer.
With a few phone calls a possible cause is the timing chain skipped a tooth cause of the lucas being to thick, other cause could be the tensioner finally went out?
Right know the car car has a rough idle and seems to be finding idle , and a noise from the engine around 4000 rpm.
I am waiting for the engine to cool off before i open her up to check timing.. if the chain is off a a tooth what could be the cause?
View 4 Replies
Advertisement
Driving home from work this evening and engine light lights up, also car started to idle very rough.... long story short got the car home and checked with vag com... 2 engine codes
000768 - Random/Multiple Cylinder Misfire Detected
P0300 - 001 - - MIL ON
Freeze Frame:
Fault Status: 11100001
Fault Priority: 2
Fault Frequency: 1
Mileage: 86567 km
Time Indication: 0
Date: 2012.12.31
Time: 14:26:57
[Code] .....
After looking around online found out it could be a variety of reasons... gonna change spark plugs tomorrow hoping that's the problem... next cheapest fix would be the ignition coils... I'm just hoping its not internal, like piston or rings.
It's a 2007 Passat Wolfsburg 2.0T.... just went over the 53k mark.
View 10 Replies
Only thing I've noticed is the idling is a little rough but the car has 88k on it so that's expected. I haven't checked the cam follower yet and know I'll probably need to change it so that's going to happen in the next week.
I had a code for P000A & P2293 for a few months that would throw a MIL and I would reset it and it would come back after a while. I finally replaced the cam sensor and I didn't see a MIlL for about 6 weeks and one day it came back. Once I scanned the car it showed P000A again. I cleared the code and everything seemed fine until yesterday. I went to start the car and the car wouldn't turn over.
I pulled the key out and tried it again and it worked. More and more I think about it, the car doesn't turn over smoothly over the past few months but maybe I'm just looking for things. I ended up scanning it last night and it had a code for P2293 & P0011. I cleared them both but what could be causing all this and cannot afford to bring the car in to the mechanic. It's out of warranty and I'm broke and X-Mas is around the corner.
2006 Passat 2.0T
View 2 Replies
Check engine light and P0010 code in my Gen III 2010 Prius...
View 2 Replies
I have a 2006 Sonata with an intermittent check engine light. The light will be on for a few days then goes out for a day or two. This pattern has been going on for about 3 months now. A scan tool was used and showed the code P0011. I know this code has to do with the camshaft timing. My question is should the light be going out on its own if there was a problem with the camshaft timing? Does the engine correct itself and then experience the problem again. Is it normal for check engine lights to go on and off with out being manually reset? Could this be a faulty sensor or loose wire causing the light to go on and off? The car has about 75,000 miles, mostly Hwy, and is driven just about everyday.
View 36 Replies
I have already concluded I need to replace my OCV on my 2007 2.4L GLS Sonata.
I have also been starting to hear a clicking noise associated with reducing throttle when in the 2500-3100 rpm range. It seems to only make this quiet clicking noise when the throttle is reducing and within the RPM range from above.
I am just wondering if this may be associated with the OCV needing to be replaced. I suppose I will find out for sure when I do finally get around to replacing the OCV sometime this month.
View 2 Replies
I have a 2007 Yaris, 180,000 miles, The check engine light comes on. With a P0011 code. I know that that could mean either:
blocked oil passage
Mechanical timing fault
Camshaft position a timing over advance
Failed OCV
Or VVT controller assembly fault
Since it's been really cold out I figured maybe it was a blocked oil passage, but after an oil change and quick check - I no longer think that's the problem.
The car runs great and it doesn't seem anything is wrong at all ...
View 3 Replies
The past two times I've driven to work I've hit significant traffic. While in the middle of stop and go traffic, the engine started to idle at high RPM (3000-4000). Today the temperature gauge really started climbing and hit the red, at which point I shut the car off and waited a few minutes. No smoke, no noise and no check engine lights. As soon as the road started to clear and we were moving again, the car was fine. The engine cooled, stayed cool, and the idle returned to it's normal 1000 RPM.
The dealer was unfortunately unable to reproduce these findings, though they thought it could be a stuck thermostat.
View 1 Replies
I own a 2001 BMW 325i. I bought it in 2011, it was in excellent condition, except for a small oil leak. I fixed the leak and then everything started happening. I've replaced so many things in this car that I've actually put more in to it then what I paid for it. This last issue was a rough idle and the scanner was showing me the code for a misfire. I took it in to the mechanic, he found that it was the first injector, replaced it, the night I picked it up it was still doing the same thing...engine light popped on. I brought it back the next day, they kept it for over a week, running test after test, finally they did an internal survey and found that the first cylinder is damaged and the shop has condemned the engine. My question is this: Is there no way to repair a cylinder? How or why does this happen and how much longer can I drive the car before it craps out on me. So far, it is rough when it's cold..but once it warms up it rides just fine. Engine light comes on and then goes off.
View 2 Replies
So I was driving home from when my engine started to sputter once it hit 4000 rpm and the CEL came on so I figured it was my plugs and coils, I changed all of those and unplugged my battery to get the CEL to go away, now all of a sudden my computer is crazy, I have a lot of indicators and my gears indicators are all highlighted, when I start the car and put in it gear is shifts really hard, I just don't know what to do!
View 4 Replies
I have a 2006 Hyundai Sonata with a 2.4 liter 4-cylinder engine. After filling the gas tank, the car idles roughly, but accelerates and performs fine at higher speeds. The rough idle lasts about 5-10 miles and then goes away.
Six days ago, I changed the spark plugs and air filter. Four days ago, I filled up with gas (and had the same issue with the rough idle). This morning, I started the car and idled it for 2 minutes while I scraped ice off the windows. I drove the car about 5 minutes and the check engine light came on. I took it to Autozone and the code given was P2187, System too lean at idle bank #1. "
Autozone suggested that it could be an air intake fault (MAF sensor), fuel pressure, or vacuum leak. They also said they have a MAF sensor cleaner to try. I am not sure if the rough idle after fill-up and check engine are related. Also, I don't know if the spark plugs or air filter could be related to the check engine. I was planning on making some easier checks first such as hoses near where I worked last weekend, especially near the air filter. Cleaning the MAF sensor is easy too. I was also going to check for vacuum leaks (incl. intake manifold) and recheck the spark plugs.
View 4 Replies
1997 lexus ls400 204500 miles, engine light is on code P0340 (cam shaft position sensor bank 1), rough idle at start, once the car warms up it runs ok but loss of power, hesitates, if press more on gas pedal the car jerks. I have replaced both cam shaft position sensors and engine coolant temp sensor but no improvement. What could be the problem?
View 15 Replies
My 04 F150 has started having a rough idle. While in park the engine will stall out with the A/C off. Also when in drive the truck will idle close to 1000rpm's. I had to the fuel filter cleaned and also the MAF sensor cleaned. Also did a vacuum check on it. Pulled the code and it's throwing a Lean Code. What else should I be looking for?
View 12 Replies
2004 F150 5.4 3v. I bought the truck with 102k on it, it now has 124k. In the morning, when the outside temp is between 30-50, the engine starts and runs fine. When I get to the first red light ( about 1 mile away) within seconds of the engine at idle, engine starts to run rough and CEL. Every time the code is p0351. If I let it sit in the driveway to full warm up... no problem. If I start the truck, shut it off and restart...no problem. It only happens at the cooler temps. I have changed plugs, used motorcraft, nickel antiseize, torqued, etc. Ford changed the coil, I have changed the coil, cleaned MAF. As soon as I cross the intersection, light stays on, rough running clears up, and runs like a champ for the rest of the day.
View 2 Replies
When exiting off the freeway and stopping at the light, my car felt as though it was bucking and idling very rough. I put the car in Neutral and it subsided a bit but the lit gauges were pulsing with the idle. It felt as though the car was going to die. I put the car back into Drive and it drove fine. I pulled over and shut the car off. There were no warnings or any other indicator lights on during this time. After shutting the car off and leaving it for a couple mins, I started it back up and the engine light was now on steadily. The rough/bucking idle was present as well. I ended up driving the car to the dealer where it is now being diagnosed and I haven't heard back.
View 6 Replies
I recently purchased an 06 f150 fx4 5.4L with 60K miles. Just recently my check engine light came on and I've noticed a slight rough idle in park. I took it to autozone and the code read P0422 evap emission leak. Bought a new fuel cap but didn't work... EGR valve?
View 2 Replies
I bought a 1999(b5) passat, 1.8t(AEB) 5spd, came with a DIRTY K&N so i cleaned it with the cleaning kit....
Car drove fine, then: started it up after an hour or so.. it was idling rough, then would spike(17-1800), idle rough, idle fine, spike....etc. just random. it went away for a few minutes, so i tried to drive it home... got 1/8 mile into 3rd... and car just bogged down so i slowed to stop and turn, went to go, it was idling rough so i couldnt drive, just "hobble" into parking lot.... i let run, more random rough, spike, fine... so i let it sit, off. when i returned, it was the same, but now CEL light on...
Codes: P0103 - Mass or Volume air flow sensor circuit high input
P0134 - Heated Oxygen sensor - bank 1 sensor 1 (H02s11) sensor circuit no activity detected
View 2 Replies
I have a 2000 VW Passat with the 1.8L turbo. When I bought it, the timing belt was off 1 notch. After I fixed the timing issue the car still didn't idle well. I was told that the throttle body was causing the problem so I replaced it. The car ran good for about 5 minutes after I replaced the throttle body. After I hooked up a OBD-II scan tool up to it instantly started running rough. The car runs at 1100 rpm at a cold start-up but when the car warms up it idles down to 850 +-75 rpms. I cleaned the MAF sensor, and it still runs rough. Car has 180,000 miles and MPGs are also down.
View 2 Replies
The 2001 Passat 1.8lT has an engine warning light on and feels like it is running on less than all four cylinders.( very rough idle) This is the first time we have seen this particular warning light and the manual suggests that it has a problem with the catalytic convertor.( 170K miles on the car) The car had no symptoms until the light came on today and the car was serviced last week. ( oil change and new tires) It seems that every time I take the car in for service something goes haywire shortly afterward.
View 6 Replies
Wifes car began to idle very rough and check engine light began to blink and beep, I took it to the mechanic today and he informed me that my control module was no good and it was a $400 dollar piece. I said go ahead get it done, cuz she needs the car and i couldn't afford to not have it done immediately. Question I have is does this small-ass piece really go for that much on average and what control module is it?
View 4 Replies
So I was warming up my car after work tonight, and it was idling really rough right above 1RPMS and i heard a lil knocking noise from the engine what could have caused this? I was parked on a slight hill but i doubt that has something to do with it.
Also my buddy told me a way to see if my clutch was going out, is to try and kill the car while in gear, so i tried 1st time it shook really really bad but didn't die. So I tried again and it seemed like it was trying to catch its self and then shook bad again and then died. I did this in 1st gear just letting off the clutch before giving it gas. Does this mean my clutch could be going out already? the car only has 63k on it...
View 11 Replies
