Passat (B5) :: Loss Of Power When Accelerate Medium To Hard - P0012 And P0304 Codes
Jun 7, 2009
Everytime i accelerate medium to hard with the CEL on like this it starts flashing and i loose power. Feels like a sputtering (in idle too). Fuel injection system cleaned and was 75% better for 1 week, but now back to same old. Reset CEL and comes back 100-200 miles later. Cam tensioner? Fuel filter? Coil packs? One of my fan clutches is pretty much out, related?
New spark plugs, maybe needs a tune up...supposedly TB was changed, but i have 106K on 1.8T 2001.5 Passat. New oil pump, timing belt tensioner put on. However A/C belt snapped and had to be put back on then tightened to work. Maybe they didn't adjust correctly at shop the timing belt tensioner?
View 3 Replies
Advertisement
We recently bought a used 2005 Camry LE 4cyl 2.4L. When we test drove it there were hardly any symptoms and no CEL. After driving it for a week we start feeling a stuttering every once in a while, no CEL still so I thought it might just need a tune up.
Replaced the plugs (which were in bad shape, were Iridiums, friend mentioned it seemed like they were burnt, white blistering like high RPM burn) with new NGK Platinums and replaced the air filter (was also in bad shape, was K&N that was badly clogged up and black).
Drove it around, let it idle, turn on AC, no problem not a hiccup. Next day arrives and the car is misfiring worse than before. CEL comes on too. We get the codes and its the P0304 I mention in the title.
We check the coils and the plugs and they fire, we switch coil 4 and 1 and clear the CEL, then later the CEL comes back on and it's still P0304 so we rule out the coils. The plugs come pre-gapped also.
The misfires are at their worst when idling and trying to accelerate hard, I can hold it at 2000-3000 RPMs with no hiccups or very few ones. Misfires worse with AC on.
Only thing left to do is check compression, try to clean the injector with fuel additive and premium gasoline, or replace the injector, at least that's what I think.
It has 86000 miles.
View 5 Replies
My 2004 Elantra occasionally won't start. When I hold the ignition on Start, the radio loses power (but the dashboard doesn't) and nothing else happens. Sometimes, tapping the gas pedal will suddenly cause the car to start. Once, I had to stomp the pedal to the floor before it would work.
I just replaced the battery (and positive cable end since it was corroded in place) and recently replaced the spark plugs (which were badly burnt). There is a check engine code for "catalyst underperforming" which seems unrelated.
I suspect my car has fuel delivery problems. It occasionally sputters while idling and often has power loss while driving if I try to accelerate hard. It seems to have trouble shifting into 4th gear from 3rd or 5th, but that may be another issue entirely.
What I should check to diagnose this, or replace to resolve it?
View 7 Replies
It's a UK VW Passat year 2000 with 1.8i longitudinal engine layout. Car has ABS
I discovered that the brakes are not releasing quickly after application. Examples where this has been noticed:
When braking and accelerating at the same time to dry brakes after puddles. Noticeable lack of power to re-accelerate when you release the brake pedal, presumably due to continued braking. Noticeable continuation of braking when trailbraking into a corner (ok sometimes I'm a bit of a racer in a family car).
What concerns me is when the snow, ice or heavy rain comes back that I might find sudden instability if the brakes aren't releasing after slowing for a corner or that worse still I'm destined for total brake servo failure.
There are no ABS related error codes although in the ice and snow I did find that the ABS fired until the pedal raised stiff and all 4 wheels just locked up (that was a fun junction crossing).
I have noticed that the drainage ducts in the bulkhead are blocked but I've never had water enter the car so I don't think it's water in the brake servo although this could have happened prior to me owning it I guess.
Working theories:
Due to slave cylinder corrosion and calipers are releasing slowly
Due to brake servo fault - either water ingress of vacuum leak
View 3 Replies
Question for those who are slammed and running a FSB. are you getting popping/clucking sounds during a medium to hard turn? what was your fix(beside removing the FSB)?
Dropped on K-sport, middle of fender to ground is 24.75"
View 2 Replies
When ever I "Brake boost" it kills the power when I hit the brake and gas hard at the same time.
View 3 Replies
Starts good cold and hot. Taking off like a grandpa on an evening drive don't notice a thing. Only codes that keep coming up are 2614 and 2617 which are cmp and ckp open curcuit codes and a software incompatibility code for FICM which is due to the updated software in the fresh FICM I installed. HPO pressures are good, has boost, idles smooth, revs nice when in park. New injectors (cause it was running rough especially cold before) and CMP and CKP (because of the above codes and didn't change)and ICP and IPR (last 2 installed because of HPO codes that are gone now with the IPR and ICP). Fuel pressure is 65psi (updated spring). When you step on it while driving it sputters and bucks like it's out of fuel, let off the throttle a bit and it purrs like a kitten. I'm a little stumped. I think it puffs a little white/blue smoke while it bucks.. not much tho. and it comes in little puffs. Took off filler cap and there is almost no blow by.
View 6 Replies
I have a 2007 F-150 5.4L and it started throwing codes p0012 p0022 p0345 and would knock and make popping sounds after it warmed up but I could rev it up and it would go away for the most part but would come right back when I started driving it. I have since pulled down the front cover and made sure it was in time, replaced both cam phasers, replaced both vct solenoids, and replaced both cam sensors. Same issue after doing all of that. I have searched the internet and have come up with nothing.
View 3 Replies
Alright, so I was driving along and everything was fine, I had no error lights and the car was running perfectly. I accidentally went over a lip of this parking lot a little too fast and all of a sudden the check engine light came on!!! I took it to Jiffy Lube and the codes I got were : c1253, c1311, p0011, and p0012. Is my car safe to drive tomarrow? Are these super expensive to fix? Could they have been set off from the curb?
View 2 Replies
5.4 3v. my last few weeks have not made me a fan. Here are the details:
I bought a 2008 F150 XL 5.4 3v with a cam phaser knock. Have done other timing jobs in past with no trouble so I was not too afraid to tackle this one. famous last words...opened the motor (shout out to the passenger side valve cover and its designer here) and found semi damaged roller follower on driver side. Worn cam lobe on the corresponding lobe and a loose chain on passenger side. proceeded to :
Change all timing components: phasers, chains, tensioners crank sprocket, all applicable bolts and BOTH cams as well as all lash adjusters and roller followers. most looked fine in fact all really did with a bit of wear on a few roller followers but only one bad one. engine didn't look to bad pretty clean.
Double and triple checked my timing chains and it was spot on. dark link on spot on crank, two dark links on the L and R dead on. put it back together. oh yes, changed all plugs with motorcraft ones, didn't even break one. did not change vct solenoids because I falsely assumed I could change the later easily if needed. they looked ok. screens intact etc... silly me for not realizing how kind Ford was in 2007 and later to necessitate removal of valve cover. I was reading a previous one on the how tos and assumed later models would be the same since it was the same sensor...
Cranked truck ran great. I mean perfect. sounded perfect. ran like a scalded cat. till it got to hot idle then it started doing its thing. rattle shake till you revved it. ran fine just wouldn't hot idle fine especially in reverse or under slight load. replaced driver side vct since ford only had one and I started on the easy side ordered the other one waiting for it. seemed to improve dramatically meanwhile I am driving this truck to test it. I drove it to work 50 miles each way and it ran great.
After a few trips it popped the P0420 light, seemed to run ok, cleared it watched it wouldn't come back. O2 sensor did seem to imply a bad cat on bank 1 since it seemed sensor two was mimicking sensor one and not staying stead like the other bank. still ran fine,
So I decided to check back pressure on the cat. I pulled sensor one out of bank one (really a joyously tight squeeze in there) hooked up my gauge and got 0 back pressure. revved it and all nothing. hooked sensor back up pulled truck out of shop and it commenced to running like crap. I mean bad. running worse than before I got it. Popping P0012 code continuously, and tons of misfire codes associated with bank 1 ..cyl 3 etc.. I tried swapping coils, pulled coils and checked spark with a tester and firing away looks like tons of good spark.
Now the weird part is : looks like bank one is dead. I can unhook any coil pack and/or injector and it runs the same and sounds like it is missing. if I unhook one off of bank 2 it almost dies or does. so bank 2 seems to be running fine. it will start and run but sounds like it missing sets flashing check engine light and backfires and stalls like crazy. I even second guessed my pressure gauge and unhooked exhaust manifold from pipe and it sounds even prettier when it backfires out of there but no change. I pulled cam sensors and cleaned it again and even tried swapping them since they looked identical but no change so I put them back.
Now I can only surmise that I am out of time somehow? or I have a gremlin perhaps? I like working on cars (usually) but this one is getting old. how do I verify what is wrong. if it is timing related how do I verify that now definitively once my marks moved I really cant figure out how to tell if it is in time? Since it has all new parts and they all ran beautifully till now. could it possibly be the vct solenoid doing all this? I plan on changing it when it comes in but surely it cant cause this many problems.. I unhooked it no change, and it does it at a cold idle and any rpm. really runs worse at idle but bad at any rpm.
View 3 Replies
Occasionally when I'm driving, I'll accelerate and get a brief loss of power, then it'll pick back up, followed by a puff of white/blue smoke. This usually happens when the oil is over 120*, but not quite to full operating temps. It doesn't happen every time either. Only 3 times in the past week. Otherwise, there is a very faint haze of white smoke that seems to be constant. It is very difficult to see unless against a dark background. Oil level is good, I check it once a week, no rising or lowering levels.
I pulled the EGR yesterday, all good, although a tad dirty. Cleaned up no problem. Haven't had a chance to do a bubble test yet. There are some DTCs, but I can't remember off the top of my head what they were. I'm about to go clean the inside of the truck, so I will pull those and update in a few minutes.
Truck has about 148,500 miles.
Torque Pro lists these codes: C1145, P0299, P0677
View 7 Replies
Car - 2004 Accent auto.- 1.6l - 97K miles
After battling a few months to get my check engine light - fault code P0304 to go off I finally remedied the problem with 3 bottles/fill ups of STP Gas treatment. This was about 1500miles ago. I go to DMV Inspection station and sat for an hour then wait anther 20minutes for the test to end and was given the big fat rejection sticker, she failed because the check engine light came on with fault codes P0304 & P0441.
Now what the heck happened here? Just bad luck and coincidence or did their test set it off? Anyway the P0441 code is new and researched it is the Evaporative Emission Control System Purge Valve. Okay where is it, the HMA manual is not specific? In relation to the intake manifold where is it? Easy fix? And will this solve my P0304 code?
View 13 Replies
I was driving my 02 camry se v6 last night and I got up to about 85 mph and it wouldn't accelerate anymore. I checked my fluids and everything seems legit and it shifts good, but there was thin white smoke coming from the trans dipstick.
View 2 Replies
I would like to find out why my car is misfiring before throwing parts at it. I have a basic level of mechanics and have checked a few things before posting here, which may or may not have ruled out some possibilities.
The problem: I have been consistently getting P0301 and P0304 but only happens sometimes, while other times there is no check engine light. I first checked the ignition coil, right side of it, that controls cylinders 1 and 4. Did resistance test, measured for voltage, and checked the wires for continuity to the connector, with everything coming out good. I know a few must have had issues with the cheap pigtail connector like me so I went and changed that but still got the misfire codes. I then put in an older known to be good working coil but no change.
After that, I removed spark plugs 1 and 4 and put them where 2 and 3 go but still got the same codes P0301 and P0304.
A friend who is a mechanic for Nissan checked the spark and wires, saying they were fine. He then checked the injectors and noticed that injector 1 didn't increase in ticking sound when RPM increased. He said I should replace injectors 1 and 4 to see if that changes anything or switch injectors 1 and 4 with 2 and 3 to see if the codes at least change. I removed them all, got two of them from junkyard just in case, made my own tool where I pumped straight fuel injector cleaner through each of them with pumped air, and put the two from junkyard on cylinders 1 and 4. I still got the same codes so then I switched injectors 1 and 4 with 2 and 3, which didn't change the codes.
I was told by another local mechanic shop that it's definitely the coil but I knew it wasn't.
Other info: I am not sure it would matter when dealing with a misfire but I borrowed a code scanner and saw that the Long Term Fuel Trim was -7%. I researched that and it means that the car is running rich and the computer is being told that it needs to run lean. I am not sure that this would make only two of the cylinders misfire and the freeze data shows that same negative LTFT for when the P0301 happened. I also know that there is an air leak at the gasket where the front cat connects to the flex pipe/rear cat. I have also gotten a rear downstream 02 sensor code once within the past month but it hasn't come back.
Would the LTFT being lean have anything to do with the misfires? Would the gasket between the two cats cause the 02 sensor to get a faulty reading? If so, would the downstream 02 sensor be able to adjust to a lean fuel mix? What else should I check?
View 40 Replies
Today I was driving my R in third gear shooting up a hill and as I was accelerating the car jerked and cel light flashed and then disappeared. I lost power for a quick second and then was restored, I just recently did the 80k service... O2 sensor maybe? There is no lights on the dash....what could it be? My tires handled great
View 12 Replies
Truck = 2011 F250 150,000 miles, no modifications, stock.
Truck lost power yesterday, no boost, and no codes. When driving on Friday, I started moving from a red light. The truck seemed very sluggish. Then I noticed it downshift going up a small hill that it never downshifts before. I looked, and noticed the turbo gauge at 0, no boost. I pulled over, turned it off, then restarted it, but still no boost, and the truck is very under-powered. I looked over the area, and do not notice any leaks, also no leaks underneath. I hooked up my OBD reader, and no codes., the boost gauge is on zero, and the truck has lost significant power. I no longer hear the turbo spooling.
I have spent the past several hours searching sites and forums (Started with FTE ), and it seems that most believe a restart of the truck has solved it for them. However, this is not the case for me, a restart, even after letting it sit overnight did not resolve the issue.
I did see one reference that replacing a NOX sensor solved their problem. This brings up some interesting truck history. Back in June 2017, my truck threw the following codes, P207F and P20EE.
P207F - Reductant Quality Performance
P20EE - SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
The message said I have 200 miles until reduced power. Since it was a Friday, not much I could do at the time so I let it sit overnight, and then the next morning the message was gone. I plugged in the OBD reader and cleared the only remaining code (P20EE), and its been a very happy truck until yesterday.
So my question, can a bad NOX sensor cause the issue of loss of turbo boost, with no codes? Is there another possible cause?
View 3 Replies
I recently had detected always misfire on those cylinders. Any relation between them?
View 1 Replies
2010 Sonata GL Sport at 122,000 kms (75,800 miles)
Engine Malfunction Light came on solid. Using ODBII reader, my Honda mechanic friend read the codes to be
P0106 Current, Pending, Permanent - Faulty Manifold Absolute Pressure sensor
P0304 Pending - Cylinder 4 Misfire Detected
He replaced MAP sensor and Coil pack. But the Engine Light remains on solid. Now its only giving code P0106 which kind of points back to MAP sensor.
Spark plugs has never been replaced so I've been suggesting to replace it anyways proactively.
Questions:
1. What else may be causing the Engine Light?
2. When do Spark Plugs typically get replaced?
View 45 Replies
2003 F150 v6 2wd 170k ... For a year I've only had codes P0171 and P0174 (lean bank 1 and 2). I was told it wouldn't hurt anything... I think now I should have taken care of it.
Anyway 3 weeks ago my truck started running a little rough. It was sputtering and had trouble getting up to speed, sometimes also the air switches from vent to defrost until switch gears and rpms go down. It gradually got a lot worse over 10 days while part was otw. A week ago i changed MAF and cleaned the black thing it's inside of. It started running better but still not good. I pulled my small trailer 2 days ago and it got worse after dropping the trailer.
Today checked codes at AZ and lean codes are gone and have p0304 (#4 misfire) and p0316 (crank sensor problem). Is this related.? Also Right before all the trouble I changed battery and alternator. Also i read online that MAF needed 2 weeks to relearn the way I drive to get correct gas/air ratio? Is that correct?
Also I read so many different things I needed to do during installation... Some say I need to turn key to the on position after unplugging old MAF then plug new one in... turn key to on position 10 times, Rev up engine, drive it rough for the first 2 minutes... etc. Is there a correct way to do it or is it vehicle specific?
Should I start by changing spark plugs and coils? The guy i bought it from and trust said he changed spark plugs right before I bought it. Will it ruin truck if I drive it? I've read so much but everyone says so much different things on the same topic. I'd what to start with or if this is related.
View 14 Replies
Well, coming home from work Friday and my truck turned on the check engine light. I did not notice any loss of power or other driveability issues. When I got home I pulled the DTC's. I got P0264, P0273, P0276, P0279, P0611, and U0306. The first four being low voltages. The Second FICM. And the last cylinder 6 misfire.
I sent a message to Ed at FICM Repair asking if there was anything to check before I pulled the beast. He said no it needed service no matter what at this point. BUT, I needed to test batteries and alternator. So I spent some time today pulling off my FICM.
I went ahead and pulled the EBP sensor and tube off from the exhaust manifold. The manifold end was very clean. BUT, the sensor end had a noticeable restriction. I would guess a 40% restriction. I cleaned the tube and the sensor and put it back on.
Next I moved to the EGR. I pulled it off and it was dirty but not what I would call restricted. The valve moved freely. I cleaned it anyway and blew out the manifold before I reinstalled it.
I have the batteries on a charger right now. Once they each charge for 12 hours each I will let them sit a day or two before I load test them. They are about four years old, AC Delco 60 month 875CCA batteries. I have had problems the last 6-8 months with staring the truck. If she sits for more than 3-4 weeks without being run she turns over slow and won't start. So I have had to jump start her a few times. And before you ask I have done a parasitic check and only have .05amp draw. So maybe the alternator is getting weak.
On that note I pulled the alternator and will get it bench tested this week. While I was there I noticed the top grooved and smooth idler pullies were a little "wobbly" so I yanked them too and will replace. Might as well do the belt while I'm at it. Boy this is going to get expensive real fast.
So, I decided to go ahead and replace the bottom coolant recovery hose and the long hose/pipe heater hose too. Boy it never ends. Oh well. I would rather do it now while I have stuff pulled off and it is easier to get to. Ordered those parts from RockAuto to the tune of 219 dollars. OUCH!!!
I accidentally broke my new engine oil dipstick while I was trying to get to the FICM!!!! CRAP!!!! More money. So......... Is there anything else I might want to look at while I am there?
The truck is 2006 F250 6.0 PSD CC SB 4x4 mid optioned XLT with 108,000+ miles. I have a 4" turbo back exhaust, AFE Cold Air Intake, Blue Spring, Hypertec Power Program 3 on the lowest setting, and an after market intake elbow at the intake manifold and an engine oil bypass filter. Turbo was pulled and de-coked about 18,000 miles back. Otherwise no issues. The 90,000 mile service was done about 10,000 miles ago. She gets regular services.
How about methanol injection? Will that keep the intake clean from the EGR sludge? I'm not thinking about added power, just keeping things cleaner? I plan to do the Atlas 40 when the FICM gets repaired.
View 14 Replies
The past couple days when driving to school in the morning i've been noticing that my car starts to rattle and struggles to accelerate once I pull out of my driveway. Once i get to the next stop sign to take off the car runs fine like nothing ever happened. My check engine light doesn't come on though. I usually let the car sit for about 30 seconds to a minute before i start to move the car. Mods I have are Unitronic stage 2, Forge 007p DV with yellow spring, and 3" downpipe.
View 1 Replies
