Replacing front wheel bearings on my 99 Passat? There is a gentle 'wahwahwah' grumble at speeds over 40mph. The car has done 130,000 miles and is otherwise in nice condition.
View 3 RepliesI've been having a lot of noise coming from the front left tire, and I finally had it diagnosed as a bad wheel bearing today.
I noticed that the front wheel bearings are sold individually while the rear wheel bearings are sold as hub assemblies. Is there a certain way that the front wheel bearings have to be removed and pressed on? I'm trying to see if this is a DIY repair.
Are just the bearings serviceable/replaceable or is the only option to get entire wheel hub assembly?
View 14 RepliesHave a 2000 Forester with 114K. Had to replace driver's rear wheel bearing at 100k & again at 110k; when replacement bearing started to fail, ABS light came on because wheel was not spinning true! Replaced passenger's rear wheel bearing at 105k (this one is getting noisy now).
Hard to believe I got 2 "bum' bearings! Not a difficult repair, but this will be 4 bearings in less than 2 years. The car's driven on paved roads & with little load, so it's not from harsh road conditions or heavy loads.
My 2005 Prius has 95k miles on it. I've been hearing a cluck-cluck-cluck noise from near the front driver side wheel. I had an independent mechanic test drive it, who said the wheel bearing needs replacement. Should I have it checked out by a Toyota dealer? They're so much more expensive, but are is it worth taking it to them?
View 15 RepliesI gotta a roaring noise coming from my right front while turning. Planning on replacing just the wheel bearings tomorrow & not the whole hub assembly(2008 2wd). Is there a thread that lays out the steps and other parts I may need? I've seen alot different stories on the net on how to do it. Everthing from I can press new bearings to I have to do 4x4 hub conversion. Seems to be some confusion.
View 2 Replies1984 K2500 4WD 8-lug
Front DS wheel hub. The front wheel bearing nuts come loose all the time. I have to check it every weekend, usually starts to get loose after a week and I have to pull apart the hub and re-tighten the nuts. Bearings are all okay, but tires wobble when they get loose...
Reverse order of install: nut -> keyed washer -> nut -> washer -> snap ring -> 4wd auto engaging assembly -> spring seat -> cap seal -> spring -> cap
My understanding is the deepest nut gets adjusted so that the bearing is tight enough that nothing wobbles but not so tight the wheel can't freely spin. Then the keyed spacer goes in and the second nut is tightened down hard to lock the first nut in position.
I've had on-and-off issues with the front DS in general as well. That side the brake caliper always start to suck in air after a few months, on #4 now. Brake system has been replaced with rebuilt MC & calipers, all new lines and warning switch. Also the 4WD doesn't seem to lock in on that hub every time. It will engage, but doesn't hold if it gets too much torque. Then other times it engages and locks and won't have any problems until next time I want to use it. It works about 70% of the time. I've taken it apart and checked everything, no burrs or wear that I've noticed to cause it.
I just got a new Sonata and I find the car has a noise like bad wheel bearings in front, it sounds like driving on really rough pavement.. I have changed the tires and still get this..
View 1 RepliesOur 2011 w/140,000 miles has a variable front end noise that I suspect from past experience with other vehicles is a bad wheel bearing. I've seen posts of the procedure for replacing the Gen 2 bearings that requires the hub and bearing be pressed out and new bearing back in which would limit the DIY'er, but looking at the replacement parts diagram for the Gen 3, it appears that the hub and bearing unit is bolted in with 4 bolts and may not need a hydraulic press to install.
View 4 RepliesIn 30 years of wrenching on cars, I've never encountered this problem. Replaced the pads and left rotor. Rotor is typical Chinese rotor. While there, replaced the wheel bearings. Also knocked out the races (with a brass drift) and replaced the races with the ones that came with the new wheel bearings. The bearings are NAPA bearings. Packed the wheel bearings just like always.
Applied some grease just like always on the spindle. Put it all back together. Tightened the wheel bearing nut while rotating the rotor in the opposite direction. Went to maybe 10 ft lbs. Backed the nut off, set it firm finger tight. Installed the cotter pin. Got a whole bunch of sloppiness in the wheel bearings. I can feel a LOT of it when rotating from the 6 o clock and 12 o clock position. What did I miss? NEVER had this happen before. 2002 f 150 2wd
looking to replace the front wheel bearings on my 06 Mountaineer. Detroit Axle? I found them on both ebay and amazon and prices almost seem too good to be true (under $100, 12 month warranty).
View 6 RepliesI m about to replace the front wheel bearing of my 2000 1.8 t I already rent the tool (hub and bearing puller and installer) from german auto parts.com but looking for pics of step by step of the process before starting the job.
View 4 RepliesI have a 2000 Passat and brought it to a local shop to have the left front wheel bearing changed. He took the car apart and said he couldnt do it because the anti lock brake wire ran threw the control arm and had no plug on it and was wired right to the dash board. Should i find a different place to take it to or is it a dealer required fix. Can i buy the bearing myself and change it?
View 1 Replies4x4 1999 Ranger ... They are a squeaking and driving me crazy. How hard are they to do, do they need a press or can they be done at home?
View 7 RepliesIf front wheel bearings can be greased through the abs wire hole on a f250 4X4, will that work on a sealed bearing on a gm product? I have done my f250 but I also have a 2004 suburban.
View 2 RepliesI have a 2000 F350 4X4 crew cab and have a vibration in the front end. I have done sone investigating and have come to the conclusion that is the front wheel bearings. The dealers says I have to buy the entire hub assemble but I seem to think different. But if I can replace the bearings any special tools that might make it easier ..
View 14 RepliesFront wheel bearings making noise. Can I buy replacement bearings/races/seals, or must i buy a whole new hub front assembly?
View 3 RepliesWhen driving at slow speeds and when I go over a bump in the road, I'll hear something like the metal part of the wheel scraping something as its turning. Only comes from the front drivers side wheel. It's audible enough that people usually turn to look when I'm in a parking lot.
Took it to the dealer, they 'test drove' it. Said they couldn't hear anything. Then said that whatever I'm hearing is 'normal suspension noise'. So after leaving it a full day at the dealer, nothing has changed. Since when is ANY suspension noise normal? But I don't think its the suspension. What to do? Take it back? Take it to another dealer?
I have some whine coming from my front wheel bearings so I'm going to replace them both. I'm not sure if this had been done on my truck before, but I'm thinking so since I have Moog greaseable ball joints.
Truck has 250k miles on it. I'm going to check the pads, rotors and slide pins. Anything else that might need work? I'm sure the half shaft could use a once over, but I don't keep my hubs locked so they don't turn much in regular driving.
After driving our 2013 Passat for 215 miles, we noticed that there was a rattling noise coming from the left front wheel area but only at slow speeds (under 10 mph). The noise disappeared at higher speeds. Today, we took the car to the dealership but they could not find anything wrong.
View 4 RepliesI have a 200 f250 v10 srw 4x4.. I've replaced the auto front lockers with warn premium manuals. I cannot get power to the front wheels. The lockers appear fine. I hear the actuator function when I activate 4x4. Whats the possibility of a bad transfer case or front diff and how do i check? I've searched but there seems to be a lot of non-answers.
View 7 Replies