I have a 01 b5.5 Passat. When I'm in tiptronic and I'm about to hit 3000 rpms, a really off noise goes off and it's like a grinding sound.... Like when your car doesn't want to go to the next gear!
View 1 RepliesI have a 2000 b5 wagon with a 2.8 5spd with 200k on it .... Its slammed on coils and i get this squealing in reverse i dont know what it is i just rebuilt the front end ie control arms... also have a nasty vibration from 1000rpms to 3000 rpms could that be engine mounts/snub mount?
View 7 RepliesI recently purchased a 2013 elantra.
I have noticed that there is engine vibration and noise felt in car and pedal when accelerating at around 2500-3000 rpm's before it shifts. Is this normal behavior? It just does not seem as smooth as it should be. I have only put about 600 miles on the car.
It has been very cold, but it does not go away after warming up.
My 1994 Acura Integra makes a buzzing noise exactly between 3000 and 3500 RPMS. It sounds kind of like the sound a circular saw would make cutting wood. It only happens when I am accelerating through that range. Also, sometimes after driving for a while, it doesn't last as long and the noise stops around 3300 RPMS. I've checked the heat shield and it seems to be fine so I don't think its that. What this could be caused by?
View 3 RepliesAt the beginning December I put my brand new winter tires (general altimax arctics) on the factory steelies and put them on the car gearing up for the snow. Not to long after the install I notice that I was getting a very strong engine vibration starting at 3,000 rpms and it stopped around 3,100 rpms no matter what gear I was in. At first I though it maybe just the cold affecting the engine. Well...
Last week I put my summer rims and tires back on for the 1,600 mile trip to MO and back, and like magic, no more heavy vibrations. Smooth acceleration throughout the normal driving rpm range. I just changed the oil and tranny fluids Tuesday after we got back and with the warmer weather the car is running smooth as silk. Still an awesome car with awesome mileage and couldn't be happier.
Let's say I'm going from zero to forty, my RPMs will hit over 3000, but when it shifts, the RPMS will drop down to 2000-ish really hard, making the car jerk. It's not a smooth drop, it's like a split second. Upon acceleration there is also a very rapid knocking sound. There's no lights on my instrument cluster.
This trouble all started after I had my alternator die, then having the car towed a few months back. Ever since then this problem has been getting worse. Wat this could be?
Codes currently on ecm: P0134, P2125, P1174, P0735 My 2003 Santa Fe 2wd 3.5l with 160,000 miles was driving fine, then all the sudden whenever I reach about 3500 rpms there's a grinding noise that sounds like its coming from near or in the automatic transmission. As for the codes: P0134- I just replaced the o2 sensor with an oem part from autozone, so not sure why that's popping up. The connections look fine. P2125 and P1174- I'm trying to figure out whether the accelerator position sensor or throttle position sensor needs to be replaced. I have a multimeter but don't know if that will be able to tell me which one is out. The P0735 gear 5 incorrect ratio and grinding noise at 3500 rpms is what I am mostly worried about though. Could a transmission flush work with that?
View 2 RepliesI have an issue with the 02 1.8t (wife has an issue). We recently took our car in to get some service work done and the mechanic informed me that he thinks the tranny is starting to go and just baby it....Fast forward a month the wife is driving the car, she said at around 40mph 2k RPM and the RPMs just drop after hearing a screeching/grinding noise....
Then she tried to apply throttle and it redlined...She said it would shoot up in RPM and not go over 30mph, she used the triptonic to get home and was able to get up to 45..Sat for a bit and I drove it, everything seemed ok..Shifts good, stops fine, no weird noises, etc....
Car is a 2002 Jetta 1.8t w/ 148k miles, regularly maintained, never had tranny oil flushed..
I have a 2010 Dodge RAM Hemi Laredo pickup. Love it. Currently 34k miles. Have kept up with all maintenance. Since about 3k miles, I have intermittently heard a "grinding" noise at about 1400-1500 rpm. Usually while accelerating going up hill/inclines. Assumed it had to do with automatic gear shifting. Have reported this to dealer maintenance folks at each visit. They have reportedly not been able to identify the source, as they claim they do not hear it, despites numerous test drives. Everyone who drives with me has heard it!. I am concerned, as at 36k my full coverage for the transmission warranty expires. Incidentally, at 33,100 miles 2 broken studs were extracted from right exhaust manifold. A new exhaust manifold gasket and 2 new studs were replaced for a different niose. Are these related, or any clue about the "grinding" that I still frequently hear at 1400-1500 rpms?
View 9 RepliesI have a 2001 accent with a 1.6 .... It won't rev over 3000rpm's. It does not have any codes being set. If I unplug the IAC it will rev up just like normal. I tried replacing the IAC, TPS, and swapped ECM and nothing has changed it. I tested continuity of the IAC circuit to ECM and it tests good. Tested ground circuit and it tests good. Have correct voltage at sensor. Not sure what else to look at.
View 21 RepliesSo I just drove my 85 to san francisco and back to Los Angles this weekend to visit my girlfriend and i had high oil pressure all the way until i blew my valve cover gasket.
So i fixed it finally today and it ran fine for a couple blocks and then my rpms shot up to about 3000 rpm and wont come down at idle speed and the car wants to keep going while in drive.
Its a 2.4l 22re EFI
Symptoms- won't rev over 3000-3500 rpm's, upon acceleration (especially uphill) seems to struggle and won't accelerate much at all, seems as if trans changes fine. BTW, throwing no codes at present.
What I have already tried...new air filter, new fuel filter, had cat. check (was told stopped up but when removed found it was not and truck did the same even with cat. off), o2 sensor (upstream) replaced, battery disconnected to reset computer.
After reset of computer, runs a little better but still not good. Seems to start if you accelerate to quickly or when truck reaches around 40-45 mph.
My oil pressure gauge jumps all over the place when I get over 3000 rpms. At lower rpms it is in the normal range and the engine sounds ok. How can I tell if this is the oil pump or the sending unit or the gauge? This is a 1980 CJ5 with a 151ci 4 cylinder.
View 2 RepliesLast night when accelerating from 40 to 60 mph I felt a "whoosh" and then the RMPs went to 3000 when I had my foot on the pedal. They dropped to 1200 if I let off. This morning the car would shift into reverse, but punching the accelerator did nothing. Other gears are fine. I rolled out of the drive, stopped at the mech and diagnostics showed only a bad speed sensor. I saw a post elesewhere that had a similar issue in 2006, same model Toyota Sienna 2000 xle. Mech pricing the transmission replacement. Could it just be malfunctioning speed sensor sending bad data to the ECM?
View 1 RepliesI have a 2012 Nissan Versa with a 1.6 Engine/CVT transmission. When going down a steep hill the RPMs rev up to at least 3000 or more...is this normal for a car to do this?
View 3 RepliesI have a 2004 saturn vue. It is a 5 speed standard with a 4 cylinder engine. Now that I have that posted here is my problem. I have normal acceleration up until I hit 3000 rpms. At that point my low engine power light comes on and I lose acceleration. To explain that better, if I take my foot off the gas pedal completely and then try accelerate again nothing happens. My engine stays on but I do not have any reaction when I push on the gas pedal. When I run the computer codes it says it could be my accelerator pedal sensor or my ecm. I do not want to have to replace the ecm if I have to due to how expensive it is.
View 8 RepliesI have been having with my ford ranger. I bought this off my nephew bcuz he needed some money and never drove it due to it being a 5speed and he has a kid and a wife and no room. OK the issue I am having is in gear or neutral I can't get the 2.5 motor over 3000rpms in any gear at all. If you rev the engine up or r driving it when it hits between 2900-3000 rpms the motor acts as if it is going to die and looses all power until you let off the gas. I have replaced the following items on the truck. Oh by the way I have a Cam 2 hand held and there are no codes or warning lights. All new parts :
1) new fuel pump
2) fuel filter
3)new timing belt
4)new motor craft platinum plugs
5) new motor craft plug wires
6)new Mass air flow meter
7) clutch,pressure plate & throw out bearing along with new slave(that needed it replaced others since I was there)
8) exhaust tube behind motor(rotted out)
9) new idle control sensor (acts as elect. Choke)
Truck starts up real quick and idles fine, but when truck is cold the rpms @ 2500 does the same as when it is warm @ 3000 rpms. I even took it to the local ford dealer in my town. Youngstown oh @ Fred martin ford. They told me the wires should be replaced and plugs along with mass air flow valve. I called them after replacing it and told them no difference and the service manager told me to bring it in again and they will look again. Service manager told me he has never heard of this type of problem and I went to a local garage mentioned it to the lead mechanic. He said that is why he doesn't like fords they are to common in chronic problems and can't be fix without a lot of guess work. I have a Hanes manual and did everything it recommends to no avail.
I have a weird issue with my 2002 4x2 manual Nissan Xterra...when I drive along (usually happens when I'm in 3rd or 4th gear), and depress the clutch pedal to start slowing down for traffic, while the gear lever is still in the 3rd or 4th gear position, the rpms start coming down as the car coasts, but then a strange grinding/whirring/grumbling noise starts happening. The noise immediately goes away if I pull the gear lever into neutral, OR if I re-engage the clutch to start accelerating again. So, it only happens when BOTH the clutch pedal is depressed, AND the gear lever is "in gear". What could this be? The car has about 115K miles, but I believe the previous owner changed the clutch recently (80-90K), and the clutch itself feels fine.
View 3 RepliesManual... I hear this buzzing sound, mostly during deceleration, on 2nd, 3rd or 4th gears between 2300-3000rpms, very annoying on 2nd and 3rd gears, but can still somewhat noticeable on 4th gear. Can also hear it on acceleration, sometimes on 2nd and 3rd gear, silent on 4th gear.
I've turned off soundaktor thru VCDS, but still hearing this sound so I was thinking that the hockey puck is still spinning, albeit not as annoying as when it's 100%. So I tried to disconnect it, still hearing that buzzing sound. I even removed all stuff from my car and it's still buzzing. Really annoying, specially if you just want to hear the sound of the engine braking on deceleration.
I've got an automatic transmission 2002 elantra 2.0 that I purchased in 2009. About a year after owning it a weird problem developed that I've just sort of lived with since. Between 25-40 mph my RPMs occasionally "bounce" persistently by an amount between 500 (mild) and about 1000 (severe). There's a bit of fluctuation insofar as what RPMs/speeds it happens at depending on outside temperature and how warm the engine is (higher temps correlate with this issue happening at higher RPMs and a more pronounced fluctuation), but it's a consistent issue every time I drive. It *seems* like my car is always trying to push down the revs, hits a certain low point depending on the gear/speed, then jumps up just a bit only to edge back down. Lather, rinse, repeat. It's not simply a display problem as I can feel and hear the engine revs changing.
No fluctuations at idle. Above 3000 RPMs it's ALWAYS smooth sailing. When I'm actively accelerating there's never a problem, even if my acceleration stays in the revolution problem range. The car is never in danger of dying, but if the cruise is engaged (ESPECIALLY in the 25-30 MPH range at operating temp) the car shudders uphill - I assume this is because the RPMs dip a bit too low for the gear the car is in. If I press the throttle the car responds normally. This bouncing RPM issue itself NEVER causes the car to shift gears in response, and if it's happening and the car DOES shift everything works fine until it goes back to trying to maintain RPMs in the problem range. When it happens I usually just increase speed by 5MPH and it goes away, though if the car is warm and the speed limit doesn't allow me to go fast enough to get out of the problem range it just does the same thing at the slightly higher RPMs.
When the problem started my car threw an OBD code - I didn't read it myself and brought the car to a random service shop who SAID they changed the throttle position sensor, and the code was gone, but a few days later it was doing the same thing without throwing a code. I tried changing the fuel pump thinking it was a fuel delivery problem, but that didn't solve anything. I put seafoam in the fuel system monthly so I'm fairly certain that fuel system gunk isn't an issue. The symptoms haven't changed AT ALL during the 6+ years this has been happening.
The kicker is that a few years ago I found a SUPERB mechanic - the first one I've ever actually trusted to be not only competent but also honest. Described the problem and even demonstrated it to him. When I brought in my car to have the struts and mounts replaced he spent two days trying to figure out what was causing the RPM issue too... and couldn't nail it down.
Possibly related: after starting the car - regardless of how long it's been running - there's a brief delay between pressing the gas pedal and the engine responding. Delay seems *slightly* longer the colder it is outside, but it's never more than a second and a half. No further delays unless I shut the engine off and turn it on again. Replacing the fuel pump didn't affect this matter whatsoever.
I own a Ford Ranger 2003, 5spd 6 cyl. My problem is when I'm driving and the engine is revving above 3000 rom's. It begins to sputter and buck as if the engine is running out of gas. It only lasts a few seconds. It ends as quickly as it starts. It does not occur each time when driving above 3000 rpms. My mechanic took the truck for a test ride and of course he could not find anything wrong. His advise was to wait until it got worse. I would rather solve the problem now. It is difficult and dangerous when trying to pass vehicles on the road.
View 2 Replies