Passat (B5) :: Got CEL While Driving Saying Cylinder 1 Misfire
Feb 1, 2012
Well I started her up and started driving her again and I got a cel! (remind you it sat all winter just got started up!) so check the cel and it says cylinder 1 misfire! ok, check spark plug gap and change # one coil to # two and two to one! everything seems fine! well get the same cel and misfire BUT this time says its cylinder 3???? so what coil packs do i change and what do i keep? the #1 and #3 were changed 18 months ago under recall! havent had any misfire since i cleared the last cel! Just change all 4? gap is at .032 on all 4 also! wires are all good and harnesses are perfect! are they just going bad or just a hickup from sitting?
View 2 Replies
Advertisement
It's a 2000 3.4 ... while i was driving on the highway the ses came on and it started running rough checked it when i got home cylinder 6 misfire came up so i did a compression test it only had 30 psi..there was a hole in a valve so i put on new heads changed the plugs and wires and a bunch of other things. put it all back together and it still does the same thing except now i have 160 psi in cylinder 6. I tried another coil, ICM, fuel injector, plug, wire and nothing changes.
View 12 Replies
I am having this failure in my engine that is making me crazy while I am driving. Yesterday i took my car to a shop to see what was it. my MAF was gone ( I replaced it ) and the failure still going on. The mechanic connected his computer in my car and we went for a ride. HE told me cylinder 1 misfire.
This is what i did.
-change spark-plugs position (failure still)
-change coilpack (failure still)
What can i do ?
-clean injectors
-check for any carbon in valves
View 4 Replies
So i got a CEL that said that cylinder #4 is being lazy. How do i figure out which is cylinder #4? Do I count them from left to right or what?
View 2 Replies
I am having a misfire code on the #1 cylinder. Its not bad but I really want to nip it in the butt before it goes out completely. I was told to try and get some of the older style coilpacks that bolt on and go with them. Can I put them on my 03 passat 1.8t.
View 2 Replies
As the title states... 2003 Passat 1.8T. The car was running fine. Had a new timing belt installed. The Check Engine light now continues to come on for Cyl #1 misfire. Attempts to fix so far include:
1) New plugs
2) New coils
3) New injectors
4) new cam and crank sensors
View 4 Replies
I have my timing belt and oil pump replaced and after 2 days the car was misfiring. Had the throttle body clean and reprogramed and still the same issue. run all test and its ok. What the issue will be. I was told it can be the ICM but the mechanic says there is no way to test it.
View 2 Replies
my dad has a 2001 Passat and he recently had his check engine light come on. We had it checked by a guy who owns a tester (snap on) and it comes up with a misfire fault on cyl #2. Wire looks good, I didn't have tools with me so I couldn't take a plug out, but do you think it could be a bad spark plug? Bad coil? Car has 89K on it.
View 5 Replies
My 2010 F150 randomly feels like I'm driving over the rumble strips as well as a small jerk like there is a cylinder misfire. If keep it at constant speed it still happens, but under cruise control it stops. Even when load increases like going up a hill.
View 14 Replies
I have a misfire on cyl 3, what is the firing sequence, changed plugs which didn't solve problem... so I'm going to try coil pack.
View 8 Replies
Today I started up my 2013 Passat SEL up and it started shaking and idling very strange. A few seconds later I had a flashing CEL so I decided to turn her off. I waited about 5 minutes (after cursing for about 4.5 if those minutes) and tried again. This time the car started and everything was fine, no CEL, no other issues. I drove for about 10 miles, shut off the engine and re-started about 5 more times with no issues.
I just had the car in for the 50K mile service at VW and everything checked out ok. I copied the VAGCON report below and I also sent it to my service manager to get his opinion. What I should do?
Saturday,02,January,2016,17:24:51:53498
VCDS -- Windows Based VAG/VAS Emulator Running on Windows Vista x86
VCDS Version: 15.7.3.0
Data version: 20151216
[Code] ....
View 4 Replies
My brother has a 98 turbo passat which is reporting misfire on cylinder #2. We swapped the coils between cylinder #2 and each one of the other cylinders and the problem did not move, making me beleive the coil is not at fault. What else should we check?
View 8 Replies
The Problem: Multiple Cylinder Random Misfire, Misfire on Cyl 2 and Cyl 3 codes. Runs fine on highway after first start in the am. Begins to misfire badly/throw code within 1 mile after exiting highway driving and starting "stop and go" city driving
The Car: 1999 VW Passat 1.8t "AEB" engine code
192,xxx miles. Greedspeed/Neuspeed ECU. All else is stock
****ICM module replaced less than 1000 miles ago due to misfire/similar problem. All was fine until now*****
Compression tested (cyl 1-4): 155lbs, 150lbs, 145lbs, 155lbs
Repairs/troubleshooting tried already:
Swapped cyl 2 and 3 coils for cyl 1 and 4. Result: problem remains / same error codes (cyl 2 and 3 misfire / random misfire)
Swapped cyl 2 and 3 injectors for cyl 1 and 4. Result: no change, problem remains
Tech is suggesting fuel system cleaning (to eliminate any carbon deposits in cylinders and clean injectors). Then look at replacing injectors if problem persists. Could I have another bad ICM?
View 3 Replies
I got 2006 vw passat 2.0, two weeks ago i replaced ignition coil pack on cylinder 3, and last Friday i replaced for second time same coil pack on cylinder 3, and today i got check engine, and it gives me a misfire on cylinder 3, it always giving me misfire on cylinder 3, the coil packs are all 4 new, i bought from a dealership, the other three coil packs does not give me a check engine, when i start the car, i feel little shaking, so what else i can do to fix this problem.
View 6 Replies
1999 Passat 2.8L. New coil pack assembly, wires, plugs, valve cover gasket(oil in plug holes). Misfire at idle and low rpm. Driving at higher rpm's misfire seems to go away. Codes are random misfire and cyl 1 misfire. Need to know if I would get an injector code if a fault or If that motor has problem with faulty cams or springs or any other common problems. I am going to do a compression check this weekend I'll update that info.....
View 9 Replies
So every once in a while I would start my car and get a rough idle but not too bad. I got a cel after a few times of this happening. I had a misfire on 1 and 4 and possible misfire on 2. It was ok for a a couple days. But during the last few days I'll start it up and it's fine. But then if I shut it off and restart it will have a rough idle again. Also today I got gas and then it rough idled and when I would shift or put it in neutral the rpm would stay up and drop slowly down. Like if I shifted gears I could almost do it without the rpms dropping at all. I've got 110k. ??
View 6 Replies
Replaced plugs and coils after I got a misfire on cylinder 2. (cheap made in china coil packs off of autoparts warehouse)
Also, plugs had 30k miles on them with original packs. Got it again.
Replaced coil on cylinder 2. Got it again.
Bought Denso double platinums. Got it again.
Moved coil packs around. Misfire on cylinder 4.
Checked plugs, good dry non corroded. Its always 2 or 4.. not 1 or 3
Slow drive with less than 30% gas pedal action it runs "ok". If I go uphill or need to step on it, not happening. Bucks like a mule.
I dont think its the fuel injector... Ordered the red audi packs off europaparts. Might need to check connections. what do i do?
I've been also reading that it could be the cam follower. I'm willing to check it and then force the dealer to fix it under the extended warranty, but if its broken I cant put it back in. The dealer is 50 miles from me.
It happened a morning I was out of gas and used .... regular! But did put in super right after that. I had spare regular gas in a container (fresh) for the generator.
Then used fuel additives. I have also been using fuel additives every other fill up just to protect injectors. I know it wont do anything other than that because of direct injection.
View 20 Replies
I'll try to break this down as best I can. I went to my mechanic this am with a check engine light. My suspicion is 02 sensors. This was confirmed as a problem area, but separate they said I had a spuratic misfire in cylinder 4. With that info, i pulled the plug to inspect (I had just installed new ngks in it and they have 18,000K on em.
I put beldon wires on about 8k ago.) plug looked to be normal, but there was definitely a puddle of oil from the valve cover leaking. Oil went into the cylinder head but I didn't really think that was an issue. Nothing abnormal jumped out at me so I reinstalled plug and checked all wire connections at both ends and called it a day.
Then I drove it. Check engine light flashing. Major performance stutters, etc. I drove it for about 20 miles and hoped it was just the oil raising hell in there and it would burn off eventually. It hasn't gone away yet. Maybe coil pack. Can the single portions of that pack be replaced, all i see them sell is the full three as a unit.
View 7 Replies
I'm having an issue with a 2008 Passat 2.0T. Engine ran rough one day and check engine light came on! I get the VagCom out, scan the ECU and get misfire on cylinder #2 and #4. Car has 109 000km. Plugs were never changed so I order some new OE Bosch platinum iridium plugs. Go for test drive after having change the plugs and I still get misfire on both cylinder number 2 and 4.
I know coil on plug are prone to be weak on those engines so I go ahead and order 4 new coils which are pretty low cost which is good. Once install on the car I go again on a test drive. car ran really smooth and no check engine light came on. I said fine! I fixed the problem only to discover the day after that the CEL decide to come back on I scan again and this time only get misfire on cyl #2 with fault frequency of 39.
I suspect my injector to be bad but before I decide to remove the intake manifold and spend another 2-300$ in parts. Any way to test my injector with VagCom in order to see if that really is my problem. Also heard the PCV could be a problem but i hardly doubt it would throw a fauly code on just one cylinder.
View 9 Replies
I've got two error codes that are persistent. The underboost code will be fixed (I HOPE) when I replace the diverter valve which is currently sitting in my trunk.
But I'm getting a persistently intermittent P0303.
Here's whats going on:
-Some mornings, I can start the car and get a very minor rough idle, it seems to miss very occasionally.
-Some mornings, PERFECT Idle.
-Some mornings, Flashing CEL, very rough idle, P0303.
It seems to go away after about 30 seconds to a minute regardless. Sometimes ver minor rough idle comes back on hot start, but not enough to set a code.
What I've done:
-Replace spark plugs. (all 4)
-Replace offending coil with brand new one.
Still having the same issues!
Can these two codes be related, and once I replace the diverter valve, things will be better?
View 2 Replies
My 04 1.8t is running rough with the cel on. i scanned it and cyl 1is misfiring. tried changing plugs. seemed to work while idling but as soon as i accelerated it started running rough again.
View 4 Replies
