When I used to change gears in my car it would feel smooth and precise, but just today when i was shifting in to 2nd, my gears started to feel clunky and like they were getting caught up on something. It feels like I'm not even engaging a gear when i put it into gear. Its so effortless and i don't get that secure feeling that i know i am in gear anymore.
View 4 RepliesI had my clutch replaced about a year ago in my 2003 mazda b2300 truck. Recently, it's been showing some of the same symptoms that popped up about a year ago. Such as, it's having a hard time going into first gear, and it seems to be generally clunky while switching the lower gears. The first clutch was replaced at 130k so I was alright with that. However, I find it hard to believe that I burned out this new one in a year. I do live in Boston, so traffic is pretty bad, but I try to not ride the clutch in traffic.
View 12 RepliesOk, so in M mode shifts can be a little rough from 2nd to 3rd unless I give it enough gas. It's no big deal and my car has always been like that (owned it since 9/2013). But as of yesterday, shifts have completely changed from 1st to 2nd. It is clunky, extremely quick and lurches forward every time in M mode. It has NEVER done this before and it kinda sucks.
I've read all of the threads regarding tranny fluid, belt squeak, etc. and haven't specifically found anything like this. I haven't done anything to the car except the ELF recall and an oil change about a month ago.
i have an 06 passat in manual, to put things short i was racing a friend last year on the highway and went from 5th to 4th at 120 thinking it was 6th and let the clutch grab ...needless to say i messed up the clutch and 2nd 4th and 6th gear felt like i was shifting into oatmeal if the RPMs were too high, BUT they would still grab.
thinking i only messed up the clutch setup, i went and got a clutch masters stage fx300 stage 3 kit with the steel flywheel (plan on going big turbo by summer)
after the shop installed the clutch, im getting the same results, better grabbing from the clutch in all gears EXCEPT FOR 6TH! 6th wont engage at all
so now im thinking i actually damaged the actual gears.
I have a 94 E350 with the 460 and the E4OD trans. that has only 30K on it.
Last weekend I took it on a 250 mile trip (one way) and it ran beautiful until the final steep hill to our vacation house. It started vibrating when it went to down shift and wouldn't pick up any speed, the OD off light was blinking. When I pushed the OD button and it cleared right up. Ran beautiful until I tried to climb that same hill again (same thing happened). It showed the same symptom when I tried to back up a steep driveway during the same trip.
Now it no longer does the vibrating but now has harsh/firm up shifts. Downshifts are smooth though, but shifting into reverse and drive are bit clunky too.
The codes I pulled were KOEO 212 and 668. After I erased the codes the 668 didn't come back. But I did change the MLPS to the new updated one from Ford and its still doing it.
I also found the 40amp mega fuse under the hood was blown too, related? Could a 1/2 qt over filled trans. cause this now too? In NH I added some fluid thinking it was low because I could not get a clear reading on the dipstick but I think the level was up there.
It only happens sometimes, but definitely everyday. I have an 06 Passat 1.8T and when i'm accelerating and it shifts gears from 1 to 2 it sounds like i have a really bad blow off valve, yet i don't. I can't see anything noticeable under the hood. I am thinking its the turbo inlet pipe.
View 3 RepliesHard shifting from the car. sort of a slam between gears and while in gear.
Possibly a mount?
My car is less than 2 months old and randomly in low gears the car will jerk or lurch when shifting gears. Is this common or does this need to be looked at?
View 18 Replies2003 Passat 1.8t FWD.
My buddy is having a wierd issue that just recently started after it's gotten cold out. The car would not start for him so he had me look at it. Attempting to start there's no sound from the starter at all. Battery is fine. When I shift in and out of a few gears, the starter engages and the car starts. Stop the car. Attempt to start it again and nothing. Shift through the gears some more and the car almost starts but quickly dies. Shift some more, start, running like a champ.
What is it about shifting through the gears that allows the starter to engage and the car to run again?
Car, 1993 Ford Festiva, 199,800 miles, original clutch, 5 speed manual transmission. Had the shifter cable replaced about 2 years ago, so that's not it. For almost the past year or so, there's been a lot of freeplay in the clutch pedal, like you have to press about halfway to the floor before you start separating the clutch, but no slipping of clutch. Mechanic said usually when clutch is slipping it will grab near the top. Its been, like, for the past few months I really have to make sure I've got the clutch pedal pressed ALL THE WAY to the floor to shift the gears. Like it grabs way down at the very bottom. And it seems the gears don't shift smooth like they used to, like the shifts are getting "crunchy" for lack of a better word, this is hard to describe in a post.
So anyway, sitting at a light, light turns green, felt a 'POP' as I pushed the clutch pedal close to the floor. So now the pedal pushes down very loosely until about the last 2 inches or so, and at any rate, almost impossible to shift gears. I can kinda jam the gears if the vehicle is moving, but taking off from a stop is darned near impossible, I can kinda jam it into second gear and rev the engine to get going. (And I only did that in order to get home) Actually I was about 80 miles from home when this happened, fortunately I was near a major interstate, only had to contend with 7 traffic lights and managed to hit 3 of them green. Rolling along in gear (any gear) seems fine, almost impossible to shift.
Car now sitting on front lawn, tried (with motor off) shifting the gears, with or without clutch pedal depressed. Gears feel 'crunchy', i.e. doesn't shift smoothly doesn't want to go into a gear. I was thinking along the lines of maybe a clutch spring or a synchronizer broke when I heard the 'pop'.
And this is off--topic, but to top it all off, I get in my other vehicle to go to the store, and within half a mile the "check engine" light comes on, but that's another topic, you can tell I had one heck of a day, someday I'm gonna buy me a new or newish car I'm getting sick and tired of patching up my rolling junkpiles, but for a variety of reasons which would be off-topic and thus verboten.
This is the second time I notice a problem with my 2014 elantra base model. The car only has 13000kms and today the car acted with a weird behaviour. This car has a manual 6 speed transmission.
Out of the blue the car jerked like it had a problem with the transmission switching gears which is weird as this is a manual.
The second time this happened the wife was driving and she said that she was in is third gear and she pressed the clutch and the brake at the same time and she felt a small jerking feel in the clutch like it didn't engage.
The problem is that I cant reproduce the problem. The car is still under warranty and I don't want to go to the dealer with a problem that I cant exhibit.
I've just about had it with this car:
- Car always had a "mushy" clutch feel. Not proper pushback against your foot feel.
- brought in several times under warranty, all was fine (documented by several dealers) from Jun- November 2015.
- Clutch then goes out at 52k, slipping in high gears. Dealer noted the pressure plate was blackened/burnt. June 2016
- I replace clutch at dealer, $1700 later. Pressure plate, slave cylinder, clutch disc, resurfaced flywheel. Pedal feel is awesome for about a month. Pedal "mush" comes back 1000 miles later. July 2016
- Take it in under the 12k warranty again, and they replace clutch master cylinder. It's about 60% better, but pedal will lose pressure occasionally and at higher altitudes (over 4000 feet) July 2016
What else haven't I replaced? And would a failed clutch master cylinder cause premature clutch wear if not replaced for months?
I don't know whats wrong, last night i was driving and all of a sudden the car started to feel like it had a flat tire. The music was loud so i was sure...i pulled over and sudden my cel starts flashing. I turned the car off looked under the hood and couldn't see much (it was dark) i turned it back on and the same thing, when i accelerate there is a loud noise that seems to come from under my seat as well as a sort of stutter/putting like right before your stall out in a manual car.
View 1 RepliesI drove a '97 with the 5.0 and AWD. I noticed that when I turned around in the neighborhood, the steering started to feel a little heavy during a U-turn. I was pretty close to full steering input to the left, but not quite at the lock. Also, it seemed like the tires might be scrubbing the pavement a little bit. No real binding or hopping, just that feel you get when you have the transfer case locked in your old-school 4X4 and make sharps turns. Is this typical for the AWD?
View 7 RepliesI got a 2000 vr6 Jetta with a 5 speed manual transmission. When shifting up or down through the gears it doesn't seem to like going into first and second. All the other gears seem fine. I've tried adjusting the shift cables and changing the gear lube, but nothing seems to work. I've heard of the cable bushings going bad and possibly shot motor mounts ( I'm at 135,000 miles).
View 5 RepliesStage 2 clutch with a diesel geek short shifter. I have started noticing shifting from 2nd to 3rd is difficult. Sometimes it will go into 5th when shifting up from 2nd. Not a lot of resistance but it is more than noticeable. How do I resolve this issue? Am I hurting my clutch if I keep driving like this? Nothing is grinding at all in between shifts.
View 2 RepliesIs it normal to feel resistance and binding of gears when shifting into L or H, when regular shifter is in neutral? One Lexus dealer technician said no, a different Lexus dealer said yes, and a 20-year private transmission shop technician said yes; the "yes" technicians said its because the gears are not synchronized and will grind and bind a little when shifting into L or H on the 4 wheel drive shifter. Car is a 2007 GX 470 and runs great.
View 14 RepliesMy car is a 2002 Hyundai Elantra with an automatic transmission. It was bought with about 79k miles on it and currently has about 94k miles. Last week I began experiencing rough shifting between gears. My CEL had been on for a few months but I wasn't having any performance problems so I ignored it. When I started having shifting problems I went to autozone to have the codes scanned. All that came up was P0441. I cleaned the purge valve and cleared the code. The CEL stayed off.
I continued driving and having shifting problems. The car slipped out of gear when it wanted to upshift. The engine revs until I release the gas. Once the rpms drop low enough the next gear would engage. This seemed to happen for every gear shift except 1-2. For my first few trips no CEL.
Finally, yesterday on my way to work I got a CEL, and it was intermittent, similar to other issues I had read about. However, the more I drove the car, the worse this problem got. It would not stay in gear while cruising down the road. I tried changing gears manually, revving the engine up and letting it drop to idle, but nothing would work. Luckily the car got me to work but it was a real jerky ride. Towards the end it didn't even want to take off from a stop. And it wasn't in third, the engine just wasn't engaging the transmission. It's like the car was in neutral. But moving the gear shifter didn't seem to work.
The car did not make it home, however. When I started it after work, it went fine for about 2 blocks and then started slipping. Within a quarter mile I couldn't even go in first. Turning off the car and waiting a few minutes, then going again would gain me some distance, but the car would start slipping again almost right away. I was able to turn around and park the car in my work's parking lot.
The problem is I have no way to pull the DTC's now because the car can't make it very far. If it's something simple like the input/output speed sensors, I'll replace those in the parking lot. I'm a DIYer and hate paying others for what I can do myself, but I may need to bite the bullet on this one.
Wife's Santa Fe has an issue with it's shift points. Its a 2002 with 148K on it, never has had a CEL, fluid is changed every 60K. Over the past few months the time it takes to shift through the gears is getting longer. What I am describing is not an actual delay between the gears, but rather how long it is starting to take to get the tranny to even shift. Sort of like how a vehicle shifts through its gears when your at a stop, and put the pedal to the floor and just hold it. it makes no difference if your barely on the gas or half way down, still takes a way longer time that it should to shift. It is slightly worse when cold, but still does it when warm. Is there some kind of temp sensor or vacuum line or whatnot that would cause something like this? When it does finally shift, its normal, tight, no slippage or delay. truck runs great other than this.
View 7 RepliesWhen shifting gears, mainly in 1st, 2nd, and 3rd while the air conditioner is on I'm experiencing jerking / clunking. When I shift it's not a smooth movement and produces a thump. The only way to really avoid this is by letting the clutch out very very slowly. It only happens when the A/C is turned on. Shifting is perfect when the A/C is off.
View 6 RepliesMy car is an automatic 1997 pontiac sunfire SE. 2.4L. I drove into a parking space and the car would not shift out of drive into park, or any other gear. I called a tow truck and the guy said that the "link" had popped out of place and it needed to slip back in. He also said the high heat (it was 109 today) can warp the plastic to where it will not stay in. He showed me this link and popped it into place. I was able to get the car to shift from low to park and then to neutral but it popped out again. So I know it's not the transmission. My question is what is this "link" called so I can get a replacement for it.
View 6 Replies