So the flexpipe on my exhaust is cracked and completely broken, so my passat sounds like a Mack truck. I've been looking into getting it fixed and I've been told i need to buy an entire new down pipe. Should i attempt to just get it fixed or buy a new down pipe.
View 4 RepliesMy flex pipe recently broke, and as a temporary fix I pieced it together using a universal flex pipe and some exhaust tape and clamps. When shopping around, I came across this:
Walker Exhaust Pipe 50465 - Read Reviews on Walker #50465
Is this an OEM part for a 2008 ford escape 3.0? It looks somewhat correct, although I do not remember seeing the other two fittings in that picture on it. (It looks like the end with the flex pipe is the end that connects to the catalytic converter, and the other two connect to the front and back headers on the engine, but I don't recall seeing a fitting like whats on the end of that flex pipe on my car (It could be that it was cut off, too).
If this is the OEM one, then perhaps the original exhaust shop cut off the fitting between the cat and where the flexpipe attaches. Is there a way that I can get parts to re-make this section of exhaust so that I can use this piece? The flex pipe they originally put in was too big and it came loose again forcing me to have to rig it again since I can't weld, and needed to get it fixed quickly.
I really do not want to replace the entire exhaust system if I don't need to, and hoping I don't have to.
How to replace this bad flex pipe....
View 25 RepliesSo I did the seafoam trick and I came to the conculsion that my exhaust leak is coming from either the manifold or the flex pipe. There was no smoke coming from under the car only a mist of smoking coming up from the back of the engine, probably by the manifold or the flex pipe. I do not see any visible cracking per say. I have attached a picture of the end of the flex pipe and it almost looks like someone may have tried to seal it before? I don't know if that is normal or not as seen in the picture.
2002 Volkswagen Golf 2.0 ...
Computer also said to replace Camshaft position sensor. The plug is getting spark and appears to be getting fuel. the plug was moist not dry. How ever i did notice the egr pipe is completely broken free from the header. Which I am replacing. Since it is reading lean on bank 2 could this alone cause more fuel to be dump in the cylinder 2 cause the plug to be too wet to fire? if not what might the possible problem be? 2000 Ford Explorer 4.0L ...
View 7 RepliesI got a 08 ford f450 sd in the shop with a cracked abd broken bolt in the driver's side exhaust manifold, any tips tricks on getting it out,I have everything loose but I can't for the life of me get the egr cooler out of the way to access the top bolts to the manifold so I can replace the manifold, or a link to a service manual would be great.
View 3 RepliesI think I need my exhaust flex pipe replaced. My car sounds so old and crappy when accelerating. Is there anyway I can cut this out and replace it myself without welding? If I do need to take it somewhere can someone recommend a good replacement part? Here is a pic of it....
flex pipe camry 5.2.2015
I have a 2004 1.8t Jetta with a rusted out flex pipe. The leak is causing a bad smell and also a lot of noise -- What's my best option to replace the downpipe (but also other parts if need be) without having to weld it?
View 6 RepliesI recently had my 06 Hyundai Sonata 3.3 v6 brought into my local repair shop for a flex pipe replacement and ever since I got it back the check engine light has come on. I brought it back in, they said the 02 sensor needed replacing, replaced it free of charge, got the car back light went back on again and they said this time they put the wrong sensor in so they replaced it, now the light is coming back on again. It seems to go on for a day then go off for a day. I've only had it back for about 3 days so far.
Could this be perhaps the 02 sensor needs to break in or the computer needs time to reset or something like that? What could be causing this issue? Should I wait a couple more days before bringing it back in to have them.
I have a ton of white smoke coming from my exhaust pipe only after it ran a long time then is started back up ????
View 7 RepliesI'm working on a friends 2003 Explorer. A couple of years ago I had to repair some broken wires in the driver door flex accordion. Now some different wires in that joint flexed and broke. My friend tried to order the whole door wiring harness and it doesn't seem available or is part of a much larger expensive harness. I looked in my Helm manual to find how this harness plugs in and it seems Helm eliminated showing all the plugs involved in a circuit.
My 1999 Helm manual shows a plug by the left kick panel for this harness. The Helm manual also doesn't include door replacement. I thought if it did include that info. it would tell me to either unplug the harness or remove the whole thing out of the door. No luck. Am I going to have to repair his old harness again? One would assume that since this is a chronic Ford failure that someone would make a better replacement solution. I had to do the same repair on another friends 2001 Ford Ranger .
On the way to an appointment an big noise started, like the exhaust was broken. See picture, how can I fix it, pull the part but do not see how the portion that got loose is hold in place buy that metal plate. Or do I need to tale it to the dealer.
Notice that there is no a lot of welding to hold it in place, that is amazing. It looks that it should be weld on the outside to avoid this problem.
2006 2.0T Passat, 83k miles
2003 Limited 6.8L v10 4WD. My oil filler pipe is cracked. Been cracked for quite a few years. Only recently did the smog shop fail the visual inspection because of it. Need to have it replaced. Auto store doesn't carry it, dealer-only item. Went to dealer and it is attached to the valve cover and sold as one piece. Any other options?
View 4 RepliesThe exhaust pipe on my 2006 Passat broke towards the front where it comes down from the engine bay. Am I going to mess it up or hurt anything by driving it this way temporarily (1 day at most) or is it just going to be loud and a little sluggish?
View 7 RepliesI have a 93 ford taurus 3.8L V6 automatic GL. The exhaust clamp between the resonator and exhaust pipe came off and I need to know what size clamp I will need to replace it. I think it is a 2 inch but I am not sure.
View 1 Repliesi have my 4 inch exhaust pipe cut just behind the rear of the cab right now with no muffler. If i cut it further up maybe jsut under the front seat or so what would this to the sound? would it make it deeper or louder?
View 7 RepliesActually developed a crack and subsequent leak in a pipe running lengthwise, so assume the factory weld over the years went bad. Since it would be a weld overhead, wonder what method would be best? Would oxy acetylene work or mig? I don't have a tig so that not an option for me.
View 2 RepliesI have a 97 Expedition with the 5.4 engine and 160k miles. Recently while having other work done I was told that I had an exhaust manifold leak due to broken rusted bolts.
View 3 Replies99 Suburban LS 4x4 with the 5.7 with 109k miles. My Suburban broke down on my wife a few weeks ago, figured out that one of the catalytic converters had a catastrophic failure and came apart internally. I cut the cat off so that I could drive it the 60 miles home to save on the tow charge.
Had the cat replaced today and now I'm blowing white smoke out the tailpipe like I'm 007 throwing a smoke screen. The smoke alternates from smelling really rich to smelling like oil (pre-burn).
The oil pressure gauge is reading at or below 20 PSI and randomly (usually while breaking or stopped) completely bottoms out. I know cluster gauges aren't known for their accuracy but I also know this isn't 'normal' behavior. I also hear noise from the engine (possibly valves sticking but could also be more of a knocking sound than a clicking one). The oil is full (actually a little too full) and it went from looking like brand new oil to jet black in less than 30 days. I talked with the rep at one of the 'big name' auto parts stores and they recommended trying a 20W50 weight oil for a couple of months. Stated they have a similar vehicle with the same motor and made the switch a few years ago and hasn't had a problem since. I plan to do an oil change this weekend, I also bought an oil pressure sending unit that I'll change out at the same time. Am I on the right track?
Also, and most likely unrelated, my coolant temp gauge is totally inoperative and is just bottomed out no matter how warm the engine is. The coolant hoses (supply and return) are warm/hot to the touch at running temp so I'm sure coolant is circulating. What's the easiest way to check whether that issue is the gauge itself, the thermostat, or the sending unit?
There are no codes that come up on my OBD II reader at the moment.
My wife's 97 f150 4x4 had an exhaust leak on the passenger side. 7 out of the 8 bolts holding the manifold on are snapped off. 4 of them are snapped off 1/8" below the top of the hole on the cylinder head . I am I unable to get a drill in to drill these out. The other 3 I've tried welding a nut on these but they won't budge and I wring the nuts off. If I have to pull the head(something I don't want to do)can I just pull that 1 head or do I have to tear the intake and everything off?
View 1 RepliesI have a 2014 Prius and I just noticed that the window on the driver's side is broken/cracked on the edge. I noticed this last night but my wife drives it mostly so I'm not sure how long it's been like that because my wife never noticed it.
View 3 Replies