Passat (B5) :: Distinct Miss And Check Engine Light Began Flashing
Mar 8, 2009
My 1999 Passat 1.8T (AEB engine) with 120,000 miles has run very well lately.............except for a recent problem. I drove 150 miles on southern California freeways, parked the car for an hour, then started it again. There was a distinct miss and the check engine light began flashing. I turned it off, let it sit for a couple hours, then plugged in a code reader. There were two codes, both the same - P-0302, "Cylinder #2 misfire". I pulled the cover off the engine, wiggled the wiring to the #2 coil, cleared the codes and started it up. There was no miss, maybe there was a little corrosion on the electrical connection?? I know there was a recall on the coils, but my car was too old to participate in the recall. Which it is - bad connection, bad coil, or something else? Or a way to diagnose it further?
View 2 Replies
Advertisement
Wifes car began to idle very rough and check engine light began to blink and beep, I took it to the mechanic today and he informed me that my control module was no good and it was a $400 dollar piece. I said go ahead get it done, cuz she needs the car and i couldn't afford to not have it done immediately. Question I have is does this small-ass piece really go for that much on average and what control module is it?
View 4 Replies
Let me start with some background. 2001 B5.5 Passat Sedan 1.8T 5spd Completely Stock 156,000 miles. So, tonight i head for the grocery store about 5 minutes up the street. I get about half way there, when I notice that the check engine light is flashing. I ease off the gas, and coax it to the next light. At the light, the car feels like it might stall out, and the car seems to shudder, and I notice that the shudder is connected to the RPM of the motor. Meaning, if i rev the motor the shudder gets faster.
I manage to coax the car home to my driveway, and I leave it in a position easy to be towed. So, i figure that I will leave the car running, and look under the hood, but as soon as I open the drivers door, i can smell something burning/smoldering. I shut off the engine, and carefully open the hood. I find no smoke or fire, but I see that the downpipe (or whatever pipe the exhaust coming from the turbo leaves through) is glowing red hot.
I am not sure what happened. The car gave no other obvious symptoms. The other things I should mention though, are that I change my own oil. Always Mobil 1 with a Audi or at least german filter. However, my father was the original owner, and for the first 60k he used conventional oil. The turbo has always been strong, and seemed to deliver full boost. I do not know if it is still boosting in light of recent events.
For the last few weeks, the check engine light has been on and off. My mechanic scanned it a few times, and told me that it was the "Air Injection Pump Code". My understanding is that this system basically divers exhaust gas into the Cat when the car is warming up. If its not working properly, then it is just a emission problem.
I should also mention, that the car has recently been leaking a little bit of water when there is a hard rain storm. On Saturday, I took the rain tray cover off, checked the Pollen Filter, and removed the battery in order to clear out the drain plugs under the battery tray, and the brake master cylinder. As I write this, I begin to wonder if its possible that something just went very wrong with the Air Injection System.
View 12 Replies
This morning I started my car and it was idling a little rough. The the Check Engine light began flashing - I immediately turned off the car and consulted this forum and my father the mechanic. After talking with my Dad and telling him that the car had sat for a week, he thought the issue was probably NOT the catalytic converter and thought it was probably related to the car sitting and possibly getting moisture in the gas. I started the car again (the roughness at idle seemed to have gone away) but the check engine light/malfunction indicator light (MIL) did not flash, it did come back on after a few seconds, but as a solid light . And as we've all read, it's OK to drive with a solid MIL.
I took the car over to Autozone and had the codes checked - P0300 (multiple cylinder miss fire) and P0301 (cylinder 1 misfire). I asked them to clear the codes. I has just put in new NGK spark plugs last month, so I didn't think it would be the plugs. I looked at a new coil pack for one of the cylinders. I decided to see if clearing the codes alone would work and drove home. No issues so far, no MIL, no rough idle, no hesitation (fingers crossed).
When I called the stearleship - they recommended I have the car towed, but would not speculate as to what the flashing MIL could be (catalytic converter or bad coil pack(s))...
View 3 Replies
My 1998 Toyota Corolla has 180 K miles. Two days ago I was putting the pedal down to get to work on time and it bucked, began chugging like a motorcycle and the check engine light (which was already on because of an emissions issue) began to flash. A mechanic looked at it and saw that cylinder 3 wasn't sparking. He changed the plugs and wires but the engine was still chugging, especially when idling. The mechanic decided it was a stuck or burnt valve because he said he could hear/feel a lack of compression in the cylinder. I'm looking for a second opinion on the issue, and a first opinion on the mechanic!
View 5 Replies
I own a 1998 ford f150 4.6l triton v8. I was leaving my house to go on a snowboarding trip about three weeks ago it was a rather warm wet day and all of the sudden my check engine light began to flash. I immediately pulled over and restarted my truck, once it was started again it was solid.
I turned around and started driving towards home. I get a small amount of feedback from my speakers and usually it's a smooth whizzing sound but as i accelerated the sound began to stutter rather than remain smooth. after about 5 minutes of driving this went away and the check engine light remained on.
so today I went out it's also a wet day and it's raining quite a lot. on my way into town everything seemed okay. then on my way home the check engine light began to flash again and the feedback from the speakers became choppy again.
I would also like to mention my battery light is on but it was on prior to the first time this happened. I'm just wondering if the belt could be loose or slipping due to the wet weather?
View 2 Replies
Im a newbie to the Camry's. Picked up from a relative a 07 Camry for $5k. It has 103K on it.
It has an issue to where it has some codes and the check engine light on with P0018, P0019, P0300, P0302, P0306 codes. They just all cam eup al lof a sudden while driving. Slight miss at idle which is the misfire codes but I can't pinpoint the issue for the P0018 and P0019 codes.
View 14 Replies
Just today, my '05 Ford Focus began flashing in orange it's O/D Off light. It seems to only happen when I am going over 40mph between 1800 and 2000 rpms. The light flashes for no specific amount of time and doesn't come on at specific intervals. I have also noticed that the car is shifting (it's an automatic) in this RPM range as well. I am worried because I just moved to a new area and am unfamiliar with the automotive services in this area. Another interesting thing that has happened along with this problem is that prior to this, my oil light had been coming on periodically. When I had that checked out they told me it was the oil pressure sensor. However, now that light hasn't gone on and I haven't had that replaced. Am I looking at a lot of trouble ahead with this car?
View 6 Replies
I just bought my wife a 2010 GX 460 and noticed an issue today with 4 Lo. When sitting with the car on, and in park, I engaged 4 Lo. The 4 Lo light began flashing along with a dinging sound. It didn't stop when I put it in drive or reverse, and just continued. The manual states I need to take it into the dealership because there is a malfunction.
View 10 Replies
It is a 1997 Ford f150 5.4 4x4 extended cab 175k miles. Took a 600 mile trip, first 300 no problems, then the "od" light began flashing, the truck shifted fine so I kept going, drove for about a 100 miles then stopped for fuel and read the code, (p1728) cleared the code and drove another 200 miles, no light no problem. The whole time there was no drivability issues. Yesterday I drove all over town, stop and go traffic, locking the TC and it would also unlock, no problems all day, drivability was fine. What to do?
1. Just keep driving it?
2. Does changing fluid fix this problem?
3. Rebuild the trans, because this was just the first notice.
4. Sell it quick no light and drives fine.?
View 6 Replies
I have a 1998 expedition 4.6 4x4 check engine light on od light flashing sometimes checked it and got p1747 code i was told epc solenoid or short on trans wiring. I already dropped the trans pan, looking for a step by step easy way to diagnose and find the short or if i need to replace any of the solenoids. I have voltmeter and taste light....
View 3 Replies
I've got a 2006 B9 with about 64,000 miles. Just a bit ago my check engine and ABS light came on, along with my cruise light flashing.
After researching a little bit on the forums and couldn't find an answer, I took it into the dealer, to which I was told that there was a bad oil pressure sensor for the right-hand side of the motor. I had them replace it out, and less than 20 miles down the road, the same lights appeared on my instrument cluster, and I took it back to the dealer. They informed me that there was now a bad sensor on the left hand side that would be another $380. I scheduled an appointment for later next week, and had them reset the error.
On the same day, about 2 hours later the lights reappeared on my dash, and I took the car over to a local parts store, where I used their scanner and the car now spit the following errors:
Camshaft position actuator A - Bank 1 timing over advan.
Camshaft position actuator A - Bank 2 timing over advan
Cam/crankshaft pos. correlation sensor A - Bank 2
Cam/crankshaft pos. Correlation sensor A - Bank 1
Camshaft position actuator A bank 1 timing over - advan
Camshaft position adctuator A bank 2 timing over -advan
Cam/crankshaft pos correlation sensor A - bank 1
I reset the codes, and waited another day for the lights to reappear on the dash. Again, I rescanned the errors, and found the same top 5 codes that I listed above.
Is there something more major going on here with the computer?
View 5 Replies
Had an issue with "check" engine light turning on and "cruise" control light flashing, intermittently. Dealer said we had dirty oil contaminating some solenoid valves in the system but we had just done an oil change and do so every 3-5K (car has 170K). They recommended switching around the sensors and doing an "oil flush" with another oil change. The warning light problem hasn't recurred, in the past month, since we started giving the gas cap a few extra turns after a fill-up. We're getting ready to buy a new car and don't want to give what might be a serious problem over to the next owner.
View 6 Replies
I have a 2007 L.L. Bean Edition Forester. The cruise light is flashing and check engine light is solid. I am well into my retirement age and nearest dealer is about 2 hours away. Is this something that local mechanic can fix? He is very good, but not Subaru schooled. I'm afraid to drive it now.
View 2 Replies
Have a Volvo XC70 and LOVE it! Recently ETS light came on and Check engine has always been on, mechanics did not seem to worried in past. As of the last month seemed to be issue with thermostat... Car would warm to normal when idling and driving below 25 mph... once I accelerated needle would drop and thermostat would go to baseline... Could feel faint warm air, but was only getting cold air coming from vents... Thought it might be thermostat stuck open?
Called my trusted mechanic and he recommended going to a radiator specialist, felt he might not be able to solve. Went to new shop today, after dropping off at 8am when they opened and not hearing from them until 4:45pm, 15 minutes before they close... Car is fixed, or so they say. Hot air is indeed coming out of vents and needle is staying where it should without falling...
BUT, now there is a strange smell (sulfur"ish") coming from the engine, and the car is shuddering and vibrating, bucking almost when car comes to a stop and then accelerates. ETS light is back on and check engine is now flashing!?! Tried going up hill on the way home and could not go faster than 20mph? None of this was happening before I took it in to the new shop today? They changed oil and oil filter and flushed radiater?
View 8 Replies
Get in my car, try to start it and BAM it hits me. As I turn the key, the engine cranks up quick, kinda too quick, if you ask me. As I go to adjust my radio, I feel my car start to jump around and shake pretty rough. As I look at my gauges, I see my check engine light start to flash. So instead of trying to drive away, I turn it off and try to start it again. Same thing happens!! So I try it again and finally a normal start. Whew, I thought that was close. But oddly enough my check engine light comes on and stays on this time, no more flashing and the engine feels fine. What the problem could be? Is it safe to drive my car?
2000 Buick Park Avenue 3.8 auto....
View 13 Replies
I have a 2004 Audi A6 wagon that's got 105k miles on it. A couple months ago, the check engine light came on while I was driving it. While it was on, it was flashing and the car felt like it was shuddering, like there was not enough gas getting to the engine. Then the CIL stopped flashing. It happened several times during my short outing that day, but then it never happened again. Now the flashing CIL is back and the car feels the same way when it's happening. I took it to an auto parts store to get the trouble codes read and the guy said P0300 (random cylinder misfire) and P0305 (cylinder 5 misfire) came up.
View 18 Replies
As the title says, my CEL goes on and flashes too.
I've read up a bit on why the CEL comes on/flash and it says it has something to do with the exhaust system and if continue operating will damage the catalyst converter (which I don't understand since I'm a car dummy.
In addition, the engine vibrates like crazy. I can feel the engine vibrating when I'm inside the car as well.
I already got the car tolled to the dealership and they kinda just told me it might be misfirings and then they said they couldn't locate the problem. So my car basically has to stay there until they open again on Monday and hopefully they will figure out the problem/fix it under the warranty and call me back.
The problem arise late Friday night and I just did a 30K maintenance on Thursday. (but the car already has 43,000 miles on it).
View 35 Replies
If you get a f!ashing cel ,the next time you start it should it flash right away or can it go back to solid on cell? 02 Accent 1.6 130 k. What can be done to check the flex pipe for a leak? Can you spray water or what? The outside looks good. Also looks hard to check around intake manifold for leaks.
View 11 Replies
Yesterday out of no where my rio started to misfire so i immediately took it into autozone to have it checked. when doing so the check engine light was on, but solid.
The tests came back with P0300, P0301, and P0302 or 3. I cant find the papers, but its 3 cyns that are misfiring. The guy at autozone suggested i try changing out the plugs first since its cheaper and has been known to fix this issue.
The second I bought the plugs I went home and changed them out. once finished i started up the car and not only was the car still misfiring, but the check engine light is now flashing... I did notice one thing when changing the plugs.
If facing the engine the second coil from the left had a bit of what looked to be rust. i was able to wipe it off with ease. What my next move should be?
View 9 Replies
I have a 98 f-150 with a 4.2 and my check engine light is on and when I'm traveling down the road i notice that when i give it gas the engine feels sluggish and my check engine Light is now flashing.
View 6 Replies
