Passat (B5) :: Car Starts Surging, Seems Like In Limp Mode
Sep 16, 2011
so i was driving the vw and the car starts surging like its in limp mode but no cel! so i stopped and checked my engine bay to see if maybe my intercooler piping came loose but nothing! so i shut it off for about 5 seconds and turned it back on and it threw a cel! the whole time i was driving it home felt like it was going in and out of limp mode and would not boost past 4 psi! check the cel and came back as this:
P0238 turbo/supercharger boost sensor a ckt high input
p0106 map/baro ckt rng perform
View 4 Replies
Advertisement
I have a 2004 1.8T AWM auto tranny Passat with APR chip. CIA, Bolt down Coil Packs, Bosch F6DTC plugs, OEM cat to straight pipe to magnaflow muffler, N75J, Forge DV (not the 007).
I installed a MBC bypassing the N75 to keep the spike at 16psi and hold (the n75J i spike at 22psi and hold 12~14), When I did that, the car will go in limp mode from 'over boosting'. I have to turn the MBC down to 9 to keep the car limping out. I love the way the MBC have the boost curve (the N75 is too passive for me). would like to fix this issue.
Also, with the N75 and or MBC, while in the APR 93 oct chip mode, I always get surging in 4th and 5th gear. Any time the boost is over 10psi, it is like I have tons of boost, but the engine is not using it. APR said it is the tranny, the tranny shop said it is the engine or computer, the engine shop said it is the tuning.
View 1 Replies
I've had the car for almost 5k miles, no issues. Only performance part on the car is a USP 3" catless down pipe with an O2 spacer. Car performed fine with it. Today I got an APR stage 1 93 octane tune. A few hours into the tune on my way home from work, I went to change lanes and the car hit some type of a wall with the RPMs. At around 3200 RPMs, the car felt like it went into limp mode. Did not let me pass 3200 RPMs. I got off the highway and had to keep the RPMs up because the car died at lights. Pulled into my driveway, plugged in my VCDS and there are absolutely no codes coming up. Nothing. But starting the car the car cranks and I have to give it gas for it I barely start.
View 24 Replies
Passat 2008/09 TSI engine 16k miles. APR stage 2+
I was driving normally and suddenly EPC light comes on, and the engine goes to limp mode. I turn the engine off and then turn on again. Everything runs fine. Vag shows N276 intermittent fail. I had already this fail, but always when starting engine, and the engine used to run OK. Is this a "sign" that is time to replace the HPFP? Or can I take the chance and keep running?
View 3 Replies
I have the problem of over boosting and hitting limp mode. now does that mean i adjusted the actuator wrong when putting it back on? if so how do i adjust it properly. or is there something else i can do to make the car come out of limp mode? also since it is boosting past a certain psi should i put a mbc on it and adjust it down?
View 1 Replies
Wife's Passat went into "limp mode" and will only give me 4th gear. Check engine light came on when it happened. I had a buddy scan the car with OBD scanner and it is saying Sensor A is bad? Which sensor this is, or thought of writing down the code that it was throwing. My guess is the speed sensor for the transmission.
Luckily the car is a W8 and has enough power to pull the car from stop in 4th gear. There aren't any reputable VW dealerships in my town or any neighboring town. I've decided to take the car to a VW/Audi specialist some 60 miles away. They told me they can take a look and replace if needed. I absolutely do not trust VW dealerships/service around here. I've heard nothing but nightmare stories about them.
View 2 Replies
My friends has an 06 3.6 motion sedan and has a problem. His car went into limp mode with the ECM and traction control light as well as CEL. we took it to the local dealer (45 min away) they scanned it and said that the throttle pedal was the only code that wouldn't clear. He ordered a new pedal from ECS and installed it today. The cars still in limp mode we read about a potential throttle body adjustment procedure (not too sure of the validity) any how followed it open hood open door ignition in the "on" position for a few minutes. After that when he started it every warning light came on. Is there a step in pedal replacement we re missing? On a side note the connector on the pedal end was fairly damaged not sure what from maybe the po had a botched replacement attempt? Not too sure what to try next.
View 5 Replies
I got into my car about 5 minutes ago and while driving i noticed a ample amount of power loss. I would go half throttle and my rmp's would go up by my speed seemed lacking even full on it it seemed to be lagging and was a slow climb to 60. Could it be my turbo not putting out or something more serious. Its a 99 1.8t ....
View 10 Replies
We have a 2006 Passat, 30K miles, live in northeast on a Great Lake. We bought it used in 5/07 with 11K miles on it. The other day, a whole mess of warning lights came on, and the car went into "limp mode." The dealership diagnosed corroded wires where they connect to the throttle valve controller. We usually keep our cars for years, and we've never had corroded wires before. Is this a typical problem of VW's? The service mgr said he'd seen about 6 come in in the last year, but I don't know if that's a lot or a few compared to other brands. We're getting ready to shop for cars again, and we'd consider a new Jetta, but not if it can't go out in the rain. Also, if the wires corroded once, what will keep them from corroding again? Should we expect this to keep happening?
View 2 Replies
Own a 2006 Volkswagen Passat 2.0t a/t. My dash board is showing a parking brake fault but as soon as the that comes up my tranny will go into limp mode ???? could the parking brake and tranny be linked together??? My parking brake still engaged and disengaged ??? what can it be ???
View 8 Replies
I have a 2008 F350 with a 6.4 Powerstroke diesel engine that just experienced total engine failure. It has around 65K miles.
There is a heavy burn star pattern on all 8 pistons, a few pistons are cracked, a few cylinder walls are scored, glow plugs are melted, both heads are cracked with multiple stress fractures in each head.
About 1 month previously, the transmission would not work in tow mode and caused the engine to go into limp home mode. The dealership just replaced the entire tranny as a warranty item. About 1 week before the engine failure, I put in a 5.25 oz bottle of Lucas injector cleaner with a full tank of gas.
The Ford dealership is saying that the star pattern on all 8 pistons is due to high pressure fuel overspray and is evidence that I had a tuner on this engine and that the warranty is invalid. I did not have a tuner. What might have caused this engine failure?
Also, they only ripped down the top half of the motor, not the bottom half. I heard this might have been caused by a cracked crank shaft, but Ford refuses to investigate this possibility.
View 14 Replies
I have a 2006 Charger R/T. My car used to not start (even thought the battery, starter, and alternator was good). I had it fixed, and the problem seemed to be electrical. However after that, it would always start, but would go into "limp mode". I let it sit for two days, and the limp mode disappeared. However, it will only start on occasion. It won't start after about 30 mins after use. It won't start for a few hours. All electrics work fine, it just won't even attempt to crank. Try to start it later, it will work fine. Even though the check engine light was NOT on, I was able to pull three codes out of it: U0100, U0103, P0700. I did have to replace the notorious "pink thingy", but everything (should be) connected fine.
View 1 Replies
Happened once or twice where I tried to back up a hill and the car went into limp mode. Neither the dealer nor my mechanic could replicate it.
View 5 Replies
So I was driving kinda hard yesterday on the highway, and it was about 80 degrees outside. At some point in the drive, I got no boost from the turbo at all (my gauge also was showing no boost). I pulled over, stopped the car, and restarted it, and the car was back to normal. Is this something I should be worried about? I am running 93 program APR Stage 1+ with VWR intake and HPFP.
View 24 Replies
My 2007 Santa Fe was acting up at one time, then stopped doing it, and recently started again. My wife is the primary driver so I'm not always in the vehicle when it happens. When the vehicle is started cold, it will run a short distance then the MIL comes on and it goes to a 5 mph limp mode. After pulling over and shutting the vehicle completely down for a couple of minutes, it will run normally with the MIL still on. However, by the time I get back home to pull the codes, the MIL goes off. I don't remember the exact codes, but when it acted up last time I believe the codes had something to do with the TPS, Pedal Pos Sensor, and one other I can't remember.
View 3 Replies
I have been having a problem where the Santa Fe will drive great for a week, sometimes only a day and the engine light will come on and the car will go into limp mode. It will drop you from 65MPH to 10 MPH, if you put it in park the RPM's will race and stomping on the pedal will not affect the RPM's. After you turn it off for a couple of minutes it will drive ok again. I have replaced the Throttle Position Sensor and the Accelerator Pedal Sensor, cleaned all connections and checked wires in them. I have also cleaned the Throttle Body. The Dealer wants to replace the Throttle Body.
Had Engine Codes:
P0123 - Throttle Position Sensor 1 Signal Circuit High Imput
P1110 - Throttle Actuator Control System Malfuntion
P0222 - Throttle Position Sensor 2 Signal Circuit Low Imput
P1175 - Electric Throttle Valve Control System (ETS) Valve #
P1196 - Throttle Actuator Control System Limp Home-Stuck
View 3 Replies
So on cold mornings my r has been kicking on the epc light and gone to limp mode. The only codes are for the coolant temp sensor and an intermittent accelerator position sensor. Would the temp sensor really cause this? After awhile I can start it up and it runs fine.
View 7 Replies
My 2010 Malibu has been throwing a code 0f 2135 also goes into limp mode. Code comes up as throttle pos sen. So looking I can see it is all built in one with the throttle body. Can it be changed with out any special tools?
View 3 Replies
I have a 2008 ISF with a k&n intake and QTP exhaust cutouts. About a month ago my car died on me and when I restarted it, the car went into limp mode. The "check vsc" light is on along with the traction light and CEL. I took it to my mechanic and he said I needed to replace the MAF sensor and I did. 100 miles later the car went into limp mode again. So I took it to a mechanic that knows Lexus vehicles very well apparently, and he diagnosed it to be my intake. So he replaced it with the stock intake. Now I've driven another 100 miles and the problem has come back again. The car is throwing all kinds of codes when I connect the obd2 scanner to it.
It is throwing p0031, p0037, p0051, p0057, p0102, p1360, p1361, and a whole bunch more.
View 14 Replies
So the other day as I was trying to accelerate my car had absolutely no power at all. it almost seemed like it went into a limp mode or something of the sort. No matter what gear or how much gas i gave it, it barely chugged along at more than an idle. I pulled over turned it off, then waited a few seconds and turned it back on, same deal. Once more, I turned it off and back on and finally, it seemed to be ok. It flashed a warning light but it cleared after I turned off the car.
View 4 Replies
My Jetta mkiv transmission went into limp mode recently. Took it into shop. They checked it out and they replaced solenoids as well as the TCU. Car still goes into limp mode. It doesn't happen all the time but enough to piss me off. Any thoughts?? Car only has 140000 miles.
View 1 Replies
