Passat (B5) :: Car Running Rough And Engine Light Came On
Sep 1, 2006
So- I take the variant in for a 65000 mi service- i.e oil change- and to get the recall done on the crankcase hose. I pick it up, drive out, and at first stop sign --- it starts running rough and engine light comes on. Take it back- they throw the computer on it and it throws a code for vacuum leak connected to brakes.. they take it back-pick up next day---they had to replace the brake booster (under warranty, extended-nice of em, I guess), because, they say, the cowling plug was plugged and water filled the booster. I HAD smelled musty water smell. But- why did it just go in the shop?? 60 bucks to unclog drain- W.
View 3 Replies
Advertisement
I have an 03 Passat with about 70K miles on it. My daughter put rug in it this morning (about 7 gallons) and since then the check engine light came on and the car is running really rough at stops. While accelerating, it seems to be fine. It is also getting about 10 mpg less than normal. MIL codes: P0300, P0301, P0302, P0303, P0304, and P0171. He said the P03xx codes were related to misfirings on each cylinder. The P0171 is a bank 1 failure (?). What do those codes really mean and could they be related to bad gas? Sent her off in my TDI JSW so she's not out on the highway if the Passat decides it doesn't want to go anymore.
View 6 Replies
Drove fairly fast (160km/hr or 100 miles/hr) then took an exit down a ramp and had to stop at a red light. Noticed all of a sudden that the engine was running bit rougher and then noticed the yellow engine light blinking. I know to turn off the engine immediately when this occurs but then all of a sudden engine light turned off and car was running smooth again.
Car has been reliable for 7 years - proper maintained, synthetic oil, 171000km, timing belt changed, burns very little oil, good torque. Should I have it checked by the dealer (fantastic fair vw dealer)?
View 3 Replies
My car recently started running rough (felt like it was misfiring). I took it to a local mechanic who went through all the normal possible problems and determined that it was a computer issue but did not have the equipment to diagnose it. I then took it to a VW dealer who said it was a bad ECU. They wanted a fortune to replace the unit so I sent it to a ECU repair shop in the UK. The repair shop said there was nothing wrong with the ECU and I have since put it back in the car which still continues to run rough. What else may be causing this issue especially considering that the VW dealer said it was a bad ECU but the repair shop said it was not?
View 1 Replies
I'm having an issue with a 2008 Passat 2.0T. Engine ran rough one day and check engine light came on! I get the VagCom out, scan the ECU and get misfire on cylinder #2 and #4. Car has 109 000km. Plugs were never changed so I order some new OE Bosch platinum iridium plugs. Go for test drive after having change the plugs and I still get misfire on both cylinder number 2 and 4.
I know coil on plug are prone to be weak on those engines so I go ahead and order 4 new coils which are pretty low cost which is good. Once install on the car I go again on a test drive. car ran really smooth and no check engine light came on. I said fine! I fixed the problem only to discover the day after that the CEL decide to come back on I scan again and this time only get misfire on cyl #2 with fault frequency of 39.
I suspect my injector to be bad but before I decide to remove the intake manifold and spend another 2-300$ in parts. Any way to test my injector with VagCom in order to see if that really is my problem. Also heard the PCV could be a problem but i hardly doubt it would throw a fauly code on just one cylinder.
View 9 Replies
My mechanic tells me I need the intake manifold gasket replaced (check engine light on, engine surging, running very rough). How much damage can I do to the car by doing this repair myself and screwing it up? I've done lots of repairs on my car before -- brake pads, rotors, replace oil pan. I also have a copy of the manufacturer's shop manual.
View 2 Replies
So I was driving my 2001 1.8t last night and put the pedal to the floor to make a yellow light and the check engine light began to blink and the engine started running very rough ever since. It idles very rough and it seems like I have lost a lot of the power.
View 7 Replies
I dont know if this is related but my ignition switch went a few weeks ago, I got the part in the mail this week and was planning on changing it today, but a few days ago my 99 Passat v6 started bucking, kinda like it did when i needed motor mounts...but my engine is really weak and rough. I opened the hood and saw that my air filter hose was disconnected right after the MAF (or at least i think its the MAF).... I don't know how long its been sucking up dirty air. but does that sound like they are related? a friend of mine said if i can see the butterfly valve in the air hose, open it up and spray a can of carb cleaner in it, put the filter back on, start the car and let it run, then do it again with another can and it should fix it. I cant see the butterfly air valve in the hose, since the hose goes down behind the engine. Should i just spray it in anyway? or does have to be press on the gas pedal...
View 3 Replies
I started the car the other day and it was running really rough and engine light was on. I started pulling the spark plug wires and pulling #3 didn't make any difference in terms of decreasing performance where the others all did.
I've replaced the plug, and distributor cap. I've also confirmed with the plug out of the block that it is firing.
I'm not sure at this point what to look at next. This happened overnight, not gradually over time, and apart from running rough the engine isn't making any noises which based on sound, and how fast it happened doesn't make me think its a scoring/compression issue.
View 6 Replies
Our R32 has 2428 miles- and today the check engine light came on and it started to run pretty rough, babied it home and the the light was blinking when I turned into the driveway.. I know that booklet 3.2 in the owners manual is diagnosing catalytic converter issues...I have always used super unleaded, it hasn't even reached the halfway point of the first service.
View 10 Replies
Filled tank with 8 gallons of 91 octane to top off. One hour later noticed car running rough at idle then check engine light comes on. Could it be the coil pack? Car has been running very well until now, and this Gremlin appears. I don't think it's the gas.
2004 -V8 Treg
52,000 on the odometer
View 4 Replies
I recently replaced the head gaskets in my 2003 Malibu. First time and all seems other than it runs rough at stop lights. The check engine came back on and so I had it read and there is an air flow issue. Is there anywhere that I can get a schematic for the vacum lines? I have all over and cannot seem to find a loose or broken one.
View 3 Replies
My check engine light came on in my 06 toyota avalon. i had the code read at pepboys and they said it was something like 0300 misfire. i took it a few days later to my personal mechanic and he said nothing popped up when he tested the code. i notice the car (engine) is running a little rough though. What is the firing pattern as i want to try and fix by putting new plugs and coils.
View 1 Replies
I have a 2004 VW Touareg with 116K miles. Yesterday the check engine light came on and she is running very rough at low RPMs. The manual tells me that there is either a problem with the exahust manifold or an O2 sensor is bad. It feels as if she is struggling for air. When you start the vehicle the check engine light flashes then stays on in the cluster. What can I expect when I take it in to the dealership? Is there anything I can check before I take it in?
View 4 Replies
The check engine light came on after cleaning the engine and the engine runs rough. Where to look. 2007 Hyundai Accord.
View 5 Replies
In the last month, my car has had an awful time starting on 2 different occasions. The first time it ran really rough for about 1 minute then was ok. The second time was the same but the engine light came on. Took it to an out of town dealer and he said it showed a misfire code but could never find anything else and all looked OK. Spark plugs?
View 4 Replies
1998 Nissan Maxima had a check engine light come on and started running very rough. I took it to get a code read and came up with P0320 and P0325. I'm not worried about the 0325 since that's a knock sensor. 0320 is a misfire on cylinder 2.
With the car idling, I pulled the power connector from coil pack 2 to see if it made a difference in the idle - nope. I did the same for the other cylinders, and each responded with a noticeable change in the idle, which was remedied when it was reconnected.
I moved the coil pack from #2 to #4 (swapping them) and the same problem existed - idle was rough and didn't make a difference when I pulled the power on 2, but it did on all other coil packs. So, it seems the coil pack ins't the problem since multiple packs don't seem to make 2 work, but they work on other 4 and 6.
I then pulled the spark plug from cylinder 2, it was very black and looked in bad shape. I replaced it. Still no love.
I then put a spare plug in the coil and was able to see spark as the engine ran, so it seems that the coil pack at 2 is getting juice.
So, I have gas (big odor when the car is running - seems super rich) I have spark. Still running very rough and the 0320 code remains.
View 19 Replies
I have a 2008 Kia Rio, 4 Cyl 1.6L, and recently the check engine light came on and the car started running real rough after getting the timing belt replaced at firestone. I took it back to Firestone and they said that 2 of the cylinders where misfiring and i need to replace the ignition coils and the corresponding spark plugs, but that i also want to get a catalytic converter cleaning or flush or something like that because of the unburnt gas that was running into the converter. Is this true? They want to charge me another 100.00 for the cleaning on top of the 300.00 to replace the 2 ignition coils and spark plugs, should i get this done or can i clean it out myself?
View 6 Replies
I started my car this morning and drove to work. It's not that cold. I heard knocking sounds coming from the engine at a stop light. I lightly tapped on the accelerator to hear it better. My commute is short (3 miles), so I gingerly cruised there. I didn't try to accelerate and it didn't seem like I was suffering from loss of power either. I opened the hood and let it idol at work and couldn't really hear the knocking sound.
I downloaded the code when I got to work. After that I started the engine again and it sounded pretty normal. I'm due for my oil/filter change (~5500 miles).
Here are the codes. Any reasons to worry, or is this an one-time thing?
2 Faults Found:
001322 - Camshaft Adj. Bank 1 Intake
P052A - 001 - Cold-Start Timing not Reached
Freeze Frame:
Fault Status: 01100001
Fault Priority: 2
Fault Frequency: 1
[Code] ....
View 1 Replies
I just had my 04 5.4l engine rebuilt. Ive driven it about 500 mi and it started running rough at a stoplight. I tapped the accelerator and it started running good again but service engine light came on. I pulled the codes and they were P0022, PO345, P0340,and P0430. It has done this several times now. Everything was replaced including the phasers, except for the camshaft sensors. Could they cause this problem?
View 3 Replies
My girlfriend has a 2002 F-150 with the 4.6 V8 and I was going to change the spark plugs for her. She said it started running rough and it threw a code and check engine light. She took it for a scan and they told her the number 5 plug was mis-firing. I'm fairly handy and bought a set of the recommended Motorcraft plugs from Rock Auto, AGSF32PM. It also matched the number in the owners manual so I thought I was pretty safe.
Funny thing, when I took the old ones out, they were AGSF22WM's instead. My thinking is they are a colder plug than the supposedly original equipment, but I don't think they've been changed before. They looked well used but the color was good. The truck has about 135K on it.
Long story short, and to get to the question(s), Would there be any reason the factory would have put a different plug in the engine than what is listed? Am I asking for trouble going with a hotter plug than what's been in there (pinging or timing retardation/loss of power)? Am I just overthinking the whole thing and need to put it back together and drive it?
View 9 Replies
