Passat (B5) :: All Sorts Of Engine And Transmission Codes Came On
Sep 16, 2011
Where do I start, 97 Passat VR6 Wolfsburg Edit, 01M trans with AAA engine. 140000 miles. Here is what it is doing! Starts and runs fine.....until I stop, turn the car off, let the fans cool the engine, and then try to start it up again. Then All breaks loose. Car is running rich, almost dieing, sputtering, throws ALL sorts of engine and transmission codes. Everything from MAF sensor to misfire to trans solenoids, I mean the codes are all across the board.Then I can take my generic scanner and reset the CEL and all is good for a couple of miles.
Now, here is what I have done to the car:Tranny: new synthetic oil and filter, removed, cleaned and replaced the valve body with new solenoids, and complete wiring harness, NEW Transmission Control Module. All new 3 New trans sensors, 1 Trans Speed Sensor and 2 other sensors, g38 and g68 i think.
Engine: New, Bosh,Synthetic Oil and filter, New Ignition Switch and Key and tumbler.New Valve Cover Gasket,Bosh, Plugs and New Bosh Plug Wires., Brand New Vw ignition, Brand New Bosh, Auxiliary Water Pump and rubber gromets. New tires,...Pulled floor pan carpet out and dried up mat after the rain where my daughter left the passenger side window and sunroof open. I will try to drive it today without turning any of the lights on the dash on to see if possibly I have an electrical issue with the dash and lights or something.
View 2 Replies
Advertisement
I bought a 00 v6 sports pkg and I am in the process of getting the clockspring replaced. I have noticed a little slip in the transmission (atleast that's what it feels like to me) when I am going between 40-50mph and was wondering how serious that is. Is this something that i have to have done right away? Also would the Lucas transmission lubricant work with this. I took the car to aamco to get the trans and check engine check and they told me I needed my transmission rebuilt but I only feel a little slip only when going between 40-50. They also pulled these codes on the check engine p1565 p0430 p0171 p0174 and p1112.
View 7 Replies
I have just replaced the abs ecu and have cleared the codes, thought all was gonna be good but now two code are still coming up they are:
01044 Transmission control module - incorrectly coded
00778 Steering angle sensor-G85
View 2 Replies
I am looking for some engine code one is 35,21,32,and 55 it a grand voger 1995. I been having transmission problem it will not shift up I been told it might be a speed sensor. My rpm seem to jump up down when it idle.
View 2 Replies
It seems that my a/c, after a "flapper" was replaced, is clicking, ticking, and making all sorts of loud noises with the a/c on. Once the system is put above 74 degrees the knocking and noises go away. The noises seem to emit from directly behind the radio.
View 2 Replies
I just got a 2000 V6 Passat Wagon. The CEL light was on when I got it though I bought it knowing this. The battery was bad when I got it and I replaced it. After installing the new battery . . .. . starting worked only intermittently. It got worse and at one point I had to hold the key to the start position for about 5 seconds before the starter would even engage. Now it won't start at all. I pulled the codes (shown below) when I first got it but did not give it much credence . . . I wanted to clear the codes and drive it and re-look at the codes. . . . but I have not been able to drive it.
Other observances. . .. not sure if they are related to the car not starting:
Windows, sunroof do not roll up/down while electronic locks work. The driver side window was down when I got it and I read somewhere on this forum to use the key to raise it. . .. it worked. Alarm does not work. Radio works. . . . I found it odd that though the battery was taken out for more than 12 hrs. . . . The radio code was not required. Dome light works intermittently.
I have checked every fuse and they are all good.
Engine Codes:
18032P1624MIL Request Sign.active
18011P1603Internal Control Module Malfunction
18010P1602Power Supply (B+) Terminal 30 Low Voltage
16684P0300Random/Multiple Cylinder Misfire Detected
16690P0306Cyl.6 Misfire Detected
16686P0302Cyl.2 Misfire Detected
Transmission Codes:
17142P0758Shift Solenoid B Electrical
18158P1750Power Supply Voltage Low Voltage
View 4 Replies
My Prius is 07 with 146k in southern California, for two days every morning I took a short trip to a store then when driving back home the prius battery lost bars fast and I lost power with all sorts of warning lights. Then I drive off with no problems for the entire day. I disconnected the aux battery and that reset the Error codes, I checked the inverter pump and works properly, I checked the aux battery and shows 12v when off and 13.9v -14v when on. This happens every morning so I suspect it's the aux battery. 3months ago my dash lights went out and rebooted the car with no problems.
View 5 Replies
Was tinkering on my car this morning, and at first noticed one side had a bigger gap than the other. Ok, I really need to change strut mount bushings, no big deal. Then I actually looked closer, and they both have some lean to them, but the drivers side is much more than the other one. Is this normal? I've never noticed any play in control arm bushings or anything. So what could be causing this? I would assume they are meant to sit flat but maybe not?
View 8 Replies
I bought a 1999(b5) passat, 1.8t(AEB) 5spd, came with a DIRTY K&N so i cleaned it with the cleaning kit....
Car drove fine, then: started it up after an hour or so.. it was idling rough, then would spike(17-1800), idle rough, idle fine, spike....etc. just random. it went away for a few minutes, so i tried to drive it home... got 1/8 mile into 3rd... and car just bogged down so i slowed to stop and turn, went to go, it was idling rough so i couldnt drive, just "hobble" into parking lot.... i let run, more random rough, spike, fine... so i let it sit, off. when i returned, it was the same, but now CEL light on...
Codes: P0103 - Mass or Volume air flow sensor circuit high input
P0134 - Heated Oxygen sensor - bank 1 sensor 1 (H02s11) sensor circuit no activity detected
View 2 Replies
I have a 2006 passat and the check engine light came on so I performed a scan, the results are below. fault codes... which ones would need to be repaired immediately?
VCDS Version: Release 805.1
Data version: 20080823
Tuesday,06,March,2012,18:12:35:26365
Chassis Type: 3C0
Scan: 01 02 03 08 09 15 16 17 19 1C 25 42 44 46 52 53 56 62 65 72
VIN: WVWAK73C86P106340 Mileage: 107910km/67052miles
00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
[Code] ....
View 6 Replies
Check engine light came on yesterday evening. Advance read the codes as P0100 and P0171. The guy said something that it may be related to the mass air flow sensor. The car seems to run fine.
View 2 Replies
Ok so we have yet again the engine light on...we did a test and we have the codes P2004 and P0642. What can it be the problem this time??? what can cause this codes and is it expensive to fix? We just fix the care a couple of weeks ago( codes P0507 and P0171) and we are sooo tired of having problems.
View 4 Replies
I just bought a 2000 VW passat with 63k. I had it for a week and check engine light came on. 30 v engine ....
p0431 /16815 bank 1 below threshold??
p0421/16805 bank 2 below threshold??
Cat? or 02 sensors???
View 3 Replies
The check engine light on my 1999 1.8T Passat is on. It started with a little miss right after startup. Then in neutral, after revving the engine to say 1,500 rpm and letting off the gas, it would nearly stall. I plugged in an OBDII analyzer and came up with codes P0102 MAF or VAF circuit low input and P0304, Cylinder #2 misfire. I replaced the spark plugs, as they were old anyway. Still the same symptoms. Then I replaced the mass air flow sensor.
The check engine light still went on after it was cleared, except this time it was P0302, Cylinder #2 misfire, P0102, P1613, Auxiliary inputs aux. outputs control, and P1426 Mfg. Control/auxiliary emission controls. Soon after, the car started running fine on it's own and I again cleared the codes.
Then a day later, the check engine light is on. This time, it is only the P1426 - Manufacturer control auxiliary emission controls. The Bentley manual calls it Tank Vent. Valve Open, which doesn't mean anything to me and the Bentley manual is of no luck. (The error code almost implies that it is the famous loose gas cap, but I have checked that - unless the gasket is bad). FYI: I have 99K miles on the car.
View 5 Replies
I was just driving and the engine check light appeared. The screen says Emission workshop. its a 2001 B5 passat V6 Manual. I used a code reader and it read P1120 and P0154. Are these codes serious? Can I still drive around? What should I do?
View 4 Replies
This morning I started my car and it was idling a little rough. The the Check Engine light began flashing - I immediately turned off the car and consulted this forum and my father the mechanic. After talking with my Dad and telling him that the car had sat for a week, he thought the issue was probably NOT the catalytic converter and thought it was probably related to the car sitting and possibly getting moisture in the gas. I started the car again (the roughness at idle seemed to have gone away) but the check engine light/malfunction indicator light (MIL) did not flash, it did come back on after a few seconds, but as a solid light . And as we've all read, it's OK to drive with a solid MIL.
I took the car over to Autozone and had the codes checked - P0300 (multiple cylinder miss fire) and P0301 (cylinder 1 misfire). I asked them to clear the codes. I has just put in new NGK spark plugs last month, so I didn't think it would be the plugs. I looked at a new coil pack for one of the cylinders. I decided to see if clearing the codes alone would work and drove home. No issues so far, no MIL, no rough idle, no hesitation (fingers crossed).
When I called the stearleship - they recommended I have the car towed, but would not speculate as to what the flashing MIL could be (catalytic converter or bad coil pack(s))...
View 3 Replies
I just had my check engine light come on and checked the codes and they were P1136 running rich at idle and P1250 low fuel level. My fuel level is 3/4 full and I just installed a K&N panel filter in the airbox. While I was installing the filter I also cleaned the mass airfow sensor and then cleared the codes. The codes have come back after 2 days.
View 4 Replies
Car dumbie back again with another question.The diagnostic for my check engine light indicates numerous cold start misfire codes. The cylinders are OK. That was checked during the diagnostic.The fuel intake is carboned up. It is recommended that I clean the intake manifold. Does this mean cleaning the fuel injectors, the throttle body or both? 2006 Passat VW....
View 1 Replies
I posted earlier about my car idling roughly, the dealership is now saying it may be my engine or transmission mounts. I have a 2002 Passat wagon with 41500 miles.
View 2 Replies
So yesterday I was driving from a stoplight and for the second time in as many links, the car did something I've never experience and any of my vehicles before. It rev'd through 1-2-3 and on the 3-4 shift the rpms just held at 3k and it almost seemed the engine had lost all power or maybe I guess come to think of it seemed like the transmission was slipping. I know it had the TSB for the hard shifts which was for 1-2 and 3-4 if I remember right. I'm going to take it to the dealer but I know them by now that if I give them a general problem that isn't happening at that moment, then they'll say everything is working properly. Like I mentioned before, this is only the second time over the life of the car (45k miles) that this has been experience when I was in the car.
View 1 Replies
i have a 2000 jetta 2.0 i am in desperate need of a new transmission. Ever since I bought the car I rarely had third gear and today on my way from southeastern PA to northwest Ohio seem to pretty much completely lost first unless I really slam it in and fifth likes to disengage every now and then unless I hold the shifter in place both first and fifth were slowly giving me problems until it got really bad after todays 8 hour drive. My transmission code is EBP, is there any other codes I can put in my car from another 2.0 or do I have to get another EBP?
View 2 Replies
