Passat (B5) :: After 30 Minutes Car Stalled When Slowing Down At Stop Sign
May 15, 2006
So this morning on my way to work its pouring. Drive 30 min and while slowing down at the last stop sign the car stalls. Car wont start anymore. Not even trying to turnover. Damn TB must have snapped.
So I ended up pushing the car into my works parking lot. Luckily rain stopped by lunch time. I popped open the driver side TB cover just enough to see if the belt. The belt did not seem to have snapped. I was able to push down on it with some force. There was definitely tension on it. So I ask my buddy to try and start it. I could see the belt turning. Tried a second time to start and this time I would even hear the starter. all it would do is a clicking sound.
Is it possible the belt is really broken? I'm now thinking it might have jumped a tooth or something and now all my valves are bent. Car has 140k km. Previous owner said it was changed but could not provide any proof. I guess my question: is there anything else that would cause TB Failure symptoms. I mean the car stalled out. How could it not be the TB...
View 10 Replies
Advertisement
We have a 2012 Santa Fe Limited V6 AWD. Currently it has 17,400 miles on it. It's my wife's daily driver and has been a great vehicle. Last week while she was coming out of Target and slowing down for a stop sign she felt a "shudder" as it downshifted from 2nd to 1st. Then as she was coming up to a stop light it did it again. So, she came home and told me about it.
On the highway coming home she said it was perfectly fine but stopping at the stop sign on the off ramp it did the shudder. And so I took it out for a test drive to go get the mail. I noticed that it would shudder on the 3-2 and 2-1 downshifts. On the up-shifts it was perfectly fine. Then, I noticed as I was rolling forward at about 1-2 mph waiting for someone to cross the street the car was rolling like one of it's wheels or axles was bent. Any faster than that and you can't feel it and again at highway speeds you can't feel it at all. It's glass smooth.
Soooo, we bring it in to the dealer and they say we bent the front drivers side axle shaft. WHAT!? How in the world would we have bent that? They said we probably hit a big pot hole but it's under warranty and that they will have to order the part and to bring it back the next week. We drive it for another week and the shudder is getting worse and at this point I'm pretty sure the trans is toast. But still, on the highway it's perfectly fine.
We bring it back in to have the axle shaft replaced and they say it will be about 2 hours. And so we go on our merry way trying to kill some time. About 1.5 hours later we get a call asking us to come back in because they need to get us a loaner.
Apparently as the tech was trying to spin the drive-shaft to line up the splines in the trans with the axle shaft he couldn't turn the drive shaft even though it was in neutral. There was a spot in the rotation of the transmission and drive-shaft where it would spin freely like it should and then it would hit that spot and was almost "un-turnable". They think that is what bent the axle shaft.
So, they are going to tear apart the transmission and transfer case to find out what the problem is but most likely going to have to end up replacing one of them anyway.
View 4 Replies
Will I wear out the transmission using the engine brake to slow down faster when coming to a stop at a stop sign or light, then shifting back into D when taking off? Should I just always leave it in D unless I am driving down a steep hill?
View 12 Replies
So about 3 days ago I made a long 9 hour drive. No problems at all but I did allow my fuel to get a little lower then I normally do. About eighth a tank had 30 miles left on the digital read out. Stopped and filled up at loves where I always get my fuel. And off I went drove it down to 3/4 a tank and made it to my stopping point. Got in to go about 7 miles down the road and come to a stop sign and slowing down the truck died. I thought crap I forgot to turn off the auto start but never done that before. Stopped and stared truck as normal. Made it to my stopping point again. Headed back to the house and doing on average 55mph and truck surges like it wants to die but doesn't.
Rpms drop below 500 and it keeps going I get to same stop sign and slowing down again doing maybe 25ish and truck dies again as I have my foot on the break. Put in nut and started it right up and drive on home. Today went about same distance. Only this time I started it with key and was doing down other things while letting it run it just dies start it back up and take off get to where I was going and it surged or hiccuped so to say. Again started it once I was getting ready to leave and let it run for about 5 min and it died had the heater on as it was chilly out by the lake. Got in and restarted it and it was blowing cold air and had a diesel smell to it. Wife asked me if truck was going to blow up. Backed out of area and put in drive and made it 80' or so and truck died again doing about 10mph
Checked so far
Batteries checked and both are good
No mods done to it
New ICP sensor and pigtail
New water pump
New injectors 20k miles ago
Oil changed 1100 miles ago
New filters upper sad lower
2003 Ford F-250 King Ranch 6.0
View 5 Replies
The other day while at a stop sign in my e99 F450, I went to take off and stalled. I am not sure if the stall was my fault or not; however, it would not start. I turned the key on and the wait to start light did not come on.
The first thing I checked was the mini 30 amp fuse under the dash that controls the GRP and the fuel bowl heater. The fuse was good, and my heater has been unplugged for a while anyway. Recently my SES light came on with codes that said the glow plugs had low voltage for both banks. I have cleaned the wires a couple times and the light goes out but then comes back on after a minute or so.
I figured that maybe if it was a bad wire it finally went bad so I got jumper cables and started to try and jump wires. I moved them around and found that when I hooked one side to the positive battery terminal and the other to the small key hot wire on the glow plug relay, the light would come on and it would start. I left the cables hooked up and drove the couple miles back home.
After messing with it I figured I could run a new wire. I got a fuse tap, and went from the 30 amp mini fuse that controls this system anyway, and ran it up to the post on the GPR for my new keyed hot wire. The WTS light would cycle and it would crank, but no start. After some more messing around I decided to put both the original wire back onto the post with the new wire that I had just put on; after doing this it started right up. I took it for a test drive and a couple times the engine would act like it stalled, only for a split second. When looking down at the dash immediately after the tach would be at normal RPM and the WTS light would be on, as if I shut the key off and tried to start it again.
I suspect it is the original key hot wire that goes to the GPR. It appears that this wire also has a purpose, other then serving as only a keyed hot wire for the GPR. It has about 6 inches off of the GPR, then it goes into the harness. Where that wire goes? I will just run a new wire instead of having to dig through that harness... that doesn't look like something I would wish upon my worst enemy.
View 13 Replies
I have a 2005 Corolla with 78,000 miles. The other day it stalled at a stop sign and wouldn't start. I got it towed to the repair shop and they called me the next day with the following:
1. Under the back seat is a fuel compression module. This has gone bad. They need to take out the seat, order the part, install new.
2. The belt that drives the accessories motor (or something like that, don't recall the exact phrasing) is worn, cracking, and probably going to break. Needs replacing. Battery is corroding and needs replacing.
View 12 Replies
My car sometimes at a stop sign may randomly shut off. I try to turn the car back on and it cranks longer than usual. Then it will turn on and my epc light will turn on. And my rpms would stay at about 10k to 11k. What's going on here? Only CEL light I have on is maf sensor and i have a bad abs module.
View 10 Replies
Strangest thing! Yesterday on my way home was coming up to a stop on this back county hwy. My car started to buck or hesitate of some kind as i stopped. It was bucking while I sat at the stop sign. Then I released the brake a little to roll forward, and it stopped.
View 2 Replies
I have a 2007 Passat 2.0T wagon. I got gas this am, and on my 30 minute drive to work all was fine until I got into traffic or came to a stop sign. While at the stop sign the car started to lurch forward or even seemed to be up and down. The idle was fine, completely constant. It was like the car was hopping or wanting to push forward. It did not happen in reverse or neutral and the car was fine while driving. What this could be?
View 4 Replies
I just purchased a 2008 passat, 2.0T 6spd manual last night and I noticed today, when sitting at a stop sign it has slight idle issues, (goes up about 200-400rpms) then back down to normal idle. Doesn't seem to be causing any issues, its just pretty annoying, and everyone next to me thinks I'm trying to race them.
View 24 Replies
I have gotten a STOP Brake Fault Service Manual warning sign on my car for a couple days and now my car wont start... no ABS light is on...
View 5 Replies
I currently have a 2006 B6 w/ approx. 95k miles on it. A couple months ago I had my catalytic converter replaced at the dealership and then about a month ago my car started having issues with stalling.
Symptoms:
-Car drives normal - no loss of power or anything, but then will randomly stall when coming to a stop or slowing down, taking my foot off of the accelerator. After it stalls the red alternator light comes on. Check engine light comes on and off - lately on most of the time.
-The issue has gotten progressively worse recently, but for the past month it has been inconsistent. Sometimes I can go an entire drive and not experience it and then other times it will stall nonstop. Lately, there have also been a few times where it's taken a few tries to start it, though this is recent as before it restarted perfectly fine.
-Recently, the car has started exhibiting symptoms at highway speeds as well, occasionally brief episodes where it will begin to jerk and shake. Usually stops as pressure is applied to the gas pedal.
-Also, have issues with the parking brake... the switch seems to have randomly broken in the center (no clue how) and I keep getting a parking brake fault. Not sure if this is related or an entirely separate issue.
I took the car to a very reputable independent VW/Audi shop and after several days they still have been unable to locate the issue. Based on the codes the MIL was sending the first visit, they replaced the low fuel pressure sensor and the cam position sender. Neither fixed the problem. So, now I have to decide where to go from here... They took off the labor and only charged me for the parts.
View 4 Replies
I have a 04 lariat f150. Problem is every time I stop at a light or stop sign I hear and feel a bump. Coming from the rear I guess . Had my truck aligned asked the alignment person about the situation he said ford just do that. True or false ...
View 2 Replies
My wife was driving this morning and the car stalled when she was accelerating from a stop light. Battery light came on and she could not restart the car no power. When I got there she was able to start the car again. I drove 10 feet when the car stalled again. Noticed that the EPC came on smelled rotten eggs or sulfur from the exhaust.
Used jump cables and car started, battery light gone but EPC light came on and stays on, no blinking. I drove back home about 13 miles and no problem. Took battery to test and did not hold charge, I will replace battery. Car was at the dealer for two weeks to get the CAM, cam follower and high p fuel pump replace. Is just a battery issue or another issue for the EPC light?
View 3 Replies
My A/C will blow cold for about 3 min. and then stop for 10 min......then cold again for 3 min.....then warm for 10 min.......what is going on ? It does this when on climate control and on A/C . I had a compressor go out about 1 1/2 yrs. ago due to a fan failing...the compressor tore apart... This is not acting like that though .
View 9 Replies
My 2006 stalled twice yesterday. Was running normally, then suddenly stalled after driving for 10 minutes. Error message said something like "insufficient power available". Started up fine after that, but a few miles later had the same problem.
Some potentially relevant background. The night before these two stalls I got some cheap gas from a no name station. A month earlier my car had a really rough start and check engine light came on, but it drove fine. Mechanic diagnosed a leak in the air intake tube (into turbo, I think), and replaced it. He said he got some strange codes though. (120D, 121B, 216D, 21E0 for air mass meter and fuel trim, and also control module comm code E000, 710B, 900B).
He said if the problem reoccurs I probably need an air mass sensor replacement. Thoughts?
Given it restarts so easily, I'm not too concerned re driving the ~10 miles to my mechanic, but I'll be avoiding highways and rush hour. Or, do you think, I can damage the car by driving to the mechanic?
View 8 Replies
I have a 2000 Mazda Protege ES, with about 120,000 miles. On February 14th, Valentine's Day, my car broke down and has not functioned since then. Here's what happened, I was driving the car when it started to shake. It continued to shake for about 5 minutes, then it stalled. I was able to start he car again and it began shaking worse than before. Then it stalled again and it has not run since then.
The mechanic I've been working with has tried a new CAM sensor, replaced the computer and checked some of the electrical wiring. But nothing has worked. It's been almost 4 months and I am eager to get my car functioning properly right again.
View 1 Replies
I have a 2003 Toyota Camry with 207K miles on it. I recently replaced the catalytic converter on it in order to fix the P0420 code. I drove the car to work the next day and the test came back under the max specs. I drove back home and everything was fine. No more CEL.
Now I have the problem where the car starts normal when its cooled down, but if I drive it for a few minutes and turn it off and back on again it stalls. If I let it cool down for a minute it will turn on but idle really rough like at 400 RPMs. At times it will stall back again.
The only other thing I did differently was pump a full tank of gas at a different gas station than I normally do. Before I changed the CAT I had no problems like this.
View 2 Replies
So I went out this morning to start the truck up like I do every morning. It cranked once, and didn't start, which is somewhat normal. second crank it started right up, which is normal, then after about 2 minutes, it seemed like the rpms were bouncing and the engine got a little more slower and louder, then it dipped below 500, then stalled. After that moment nothing. It just cranks. Now it was VERY low on fuel, I've been this low on fuel and never had anything like this happen, so my neighbor took me up to the station and I bought 2 gallons. came back, still nada. I went out after letting it sit on the block heater for about an hour and noticed a small puddle of fuel under the truck on the passenger side. I went to start it and the fuel gauge went up to a half tank. cranked, no start. then again and it went up again but slowly started creeping back down.
Now the kicker, I have very limited knowledge of diesel engines, or gas for that matter. So if my intuition is right, this is probably going to be a learning experience for me... what should I check first guys? Its plugged in right now but I am sure that's not gonna fix it.. I am gonna change the oil first since it needs it, I bought shell rotella triple t 15w40 which im assuming is ok. last winter It was leaking fuel when it was really cold out but that was it, just leaking a bit and then after spring it went away. I know I should have fixed it when it started but I have an extreme anxiety to letting any mechanic near my vehicles and just about as much anxiety trying to fix it myself. I'm at a loss for what to do, I'm a pro with computers but this truck scares the crap out of me, I'm terrified I'll do something worse.
2002 Ford F250 Powerstroke 7.3 4x4, 218,000 Miles....
View 14 Replies
Last week I was changing the oil on my wife's 2004 Camry (130 000 kms). I noticed quite a LOT of corrosion around the positive and negative battery terminals.. so I decided to clean them.
I removed the negative without any problems but I could not get the positive off. I decided to use a hammer to move the connector back and forth. I was surprised with how much force I had to use to break the connector free.
Once I replaced the oil I tried to start the car but it would not start. I check the voltage and I was down to 10 volts. Obviously I had damaged the battery in getting the positive terminal off. A quick ride to the auto parts store and I had a new battery.
I installed the battery and took the car out for a spin. The car drives normally but it will NOT idle after it has been warmed up. If I come to a stop sign, the car will idle low and stall.
I have already verified that the battery is at full charge and the battery is being charged when the engine is running. No 'Check Engine' light has come on.
View 14 Replies
I just bought a 2000 Toyota Camry 4 cylinder with 150K miles. It drove great for a week. Now it wants to cut off when I'm at a stoplight or stop sign. When I press the gas there is no acceleration and very sluggish. This is when it wants to cut off and does about half the time. At normal driving speeds it drives great. The Check engine light also came on. Advance Auto Parts store read the codes and it's P440, p441, p446 and P106. All have to do with evaporative emission control.
View 3 Replies
