Passat (B5) :: 2004 - How To Remove Shift Boot From Knob
May 16, 2010
I'm trying to swap out the shift boot of my 2004 (B5.5) Passat 1.8T 4Motion and running into trouble. According to the instructions from the new Red Line shift boot, I should be able to separate the two collars that hold the boot to the knob. However, the white post that's part of the knob assembly has a piece that's bigger than the lower black collar, preventing it from being removed. Is there something I'm missing? How can I remove the boot without damaging the existing knob assembly?
View 7 Replies
Advertisement
How to release the shift knob and boot from the transmission stalk on a B6 Passat automatic?
View 1 Replies
How to remove the stick shift knob on a 5 speed 99 passat .
View 3 Replies
I'm repainting my peeling shifter trim plate and replacing the shift boot with a new one. Lots of support available on removing the shifter and disassembling the trim plate, but no clear instructions on how to remove the boot from the knob. It looks like this inside:
How do I separate the boot from the knob to install a new boot? The only instructions I found showed a metal collar which is not the case in our cars.
View 1 Replies
I have a 2011 elantra a 6 speed manual and im trying to take off the shift knob and can't seem to do it....
View 33 Replies
How Do You Remove Gear Shift Knob For Replacement ?? On My 07 Azera
View 2 Replies
How do you remove the shift knob in a 2013 Elantra GLS? I didn't see a pin or anything.
View 3 Replies
I have a 2004 1.8T 4Motion (automatic) that blew a CV joint boot. After inspection of the other side, I decided to replace both (just the outer boots). Got the axles out without much trouble but now I cannot drive the joints from the axles. I've tried both and neither is cooperating, I've knocked out off them with a mallet but they aren't budging. Is there something to do besides just driving them off?
Axles are tubes (hollow) p/n's 8D0 407 271 (& 272) ED.
View 10 Replies
I've got a 2001.5 v6 passat w/ auto and my shift knob has this cool burl veneer on it. I think it's real wood but it's pretty thin and it's got cracks on the front and the back. I can't see any simple way to remove the stick so that I can try to glue it. How to do that. But it's a standard tiprtonic shifter ... probably the standard on that model.
View 3 Replies
I am trying to remove the shift knob and the steps are entirely different than the DSG knobs from the GTI; You take just the boot off (not the assembly) then underneath is a hose clamp which needs to be removed. (this is not on the GTI version); I cannot figure out how to get this clamp off; I guess you need hose clamp pliers? And then do you need a new hose clamp? Won't it ruin the clamp?
View 24 Replies
how to change an automatic shift knob. Im interested in getting a momo automatic shift knob.
View 4 Replies
I need the PASSAT B5 shift knob part number...
View 1 Replies
Where I can find information on how to swap out the shift know on an automatic transmission in my 2003 Passat GLX? I bought a new knob but don't know how to get the old one off.
View 1 Replies
I've read a few posts of people trying and they say the cant be removed but I just don't believe it! I cut off some of the rubber on the with a knife and its all white plastic underneath.. I just don't believe that its actually impossible to remove this.
View 3 Replies
I tried searching and googling but came to no results, unless its like similar trucks. How do the 4x4 shift remove? I have an 04 F250 and someone decided to put the shift on sideways so the 4HI and etc read upside down before I purchased the truck. Do I just rip the thing off?
View 1 Replies
This car is an Australian 2014 Elantra SE
The existing manuals do not work, they show a knob previous to this one and don't apply.
Hyundai Elantra: Console. Repair procedures - Interior - Body (Interior and Exterior) - Hyundai Elantra MD 2010-2016 Service manual
Shows an earlier one and I can't find any other info.
View 19 Replies
I have a '98 F150 front 60/40 seat going into a '77 shortbox F100. I've searched and found a lot of info on repairing a lumbar support but nobody seems to mention how to get the stupid off. I don't want to break anything but I can't see any screws or clips. Does it just pull off with force?
View 1 Replies
First the wife crushes the underbody on a huge rock cutting a corner. Now she spilled a whole pop down the shift lever, and its glued shut - it will hardly move. I know how to get the console off, but How do I take just the 'shift knob' off? I need to get the flexible piece underneath it off so we can wash all the parts.. I have the upper console part off.
View 11 Replies
The other day the plastic top piece of my shift knob broke off (that had the shift pattern painted on it) and it made me once again want to replace the stock shift knob. I was considering buying one, but other than TWM I can't find any that I really like, so I want to machine one myself. My biggest problem in planning right now is what metal to use, SS is nice but expensive, and how to attach it to the leather and the stick. The only way I can think of attaching it to the stick is with set screws which would be hard to drill.
View 1 Replies
This has been bothering since the day I got my R. When im in 6th gear and let off the throttle I notice my shifter jolt a bit. Is this normal?
View 12 Replies
I went to the golf ball, but I am thinking of going back to OEM. Looking for a heads-up about the process?
View 6 Replies