a 2004 passat 1.8t 5spd came to the shop, cranks but does not
fire/run..i through the vas 5051 on there - p0688 - open circ. main relay...located this power supply relay and tested it - she had an open winding...replaced it runs excellent
1999 Passat turbo with a little over 100K miles. Car ran fine last night. This morning, the engine/starter cranks well, but no fire. And it has gas in the tank.
View 1 RepliesOk.... So I took my car for a drive to see my friend, started normally....... After an hour or so I left and this time the car cranks but will not fire........ This same problem happened in the dead of winter...... So I remove the key and let the car sit for 15 minutes and then boom it starts as it normally would.........
View 1 RepliesMy hyundai accent 2004 standard doesn't start. The engine crank, but there's no fire. I change the camshaft and crankshaft sensor. Also change my timing belt, my alternator, my starter, my control box and my computer. But if I pull the car with my pickup, it runs. While the engine is running, the computer doesn't give me any diagnostic code. I also check my fuse, relay,... Even jump start the starter to check if it was the switch.
View 4 RepliesI just finished putting in aftermarket A/C in the 2004 Ranger my dad gave my son. It's a 2.3L, STD transmission. It was running GREAT before the project started. I installed new battery as part of the project. When I started it back up it ran for 2 or 3 seconds then died. I now cranks, but does not fire at all.
I have tried one of the key reprogramming sequences (turn key to "ON" 8 times) with no success. Would it crank at all if it were a key security issue? Is there anything I need to reset anywhere else, like in the air intake system?
It's either not getting spark or not getting air. The fact that it ran for a couple of seconds has me confused. Would it run at ALL if there was a key security problem?
I had to remove and reinstall the air filter housing and ducting. Is there anything else I need to do to with the air intake system?
I just bought an 04 Ford F250 diesel 6.0 with 92k miles. Previous owner installed a UNGO alarm with remote start. Last week, after work, I started it using remote start. I got in the truck and realized I had forgotten something, so I exit the truck and leave the keys on the seat. Truck is still running. The doors lock. I reached in through the cracked window and pushed the unlock button. Here's the problem.. the truck died immediately won't start.. mechanic says it's the high pressure oil pump. I'm thinking it's the anti theft system but no luck.
View 1 Replies2004 ford ranger 3.0 ... So here it goes I am pretty mechanically incline for the most part i would say until this last week i got a rod knock. So i replaced all my push rods put everything back together and now my car cranks but just wont start up where did i go wrong. I cant afford to get another truck i just want my baby back up and running ...
View 14 RepliesThe car died randomly and now it won't fire. I know it is getting fuel, none of the relays or fuses are bad. I am pretty sure it is not getting spark. The spark plugs that were in it were pretty much gone, put some brand new ones in and while testing I didn't see it spark. The wire resistance tested fine with my multimeter. I just checked the resistance on the coil pack. High side (set to 200k ohms) was ~15.6 on either bank, low side was 0.060-0.062 (set to 2k ohms, my meter doesn't go lower).
View 2 RepliesTo start I was driving home the other night, car just stalled out and would not start back up, at all. Just cranks over and over. Things I have checked
- I am getting a spark from the plugs
- Fuel pump primes when key is turned on
- Fuel comes out of lines, even more so when key is switched over so pressure should be ok, I have not checked exact pressure due to not having a gauge.
- I have checked all relays under the steering wheel (just visual) some had brownish on the connectors and I cleaned all that off.
- All fuses are good and not blown (voltage meter also showed power coming to a few key fuses I checked.
I am down to a few things that I have read could be possible causes
- Camshaft Position Sensor
- Crankshaft Position Sensor
- Not sure what else to really check
I have a stock 1994 Celica GT with the 5sfe M/T .... I do have a headgasket leaking, and I am having another motor rebuilt and put in next month. I just need to nurse this one along for now. Right now it cranks but will not start. does not even fire up at all.
Code 12 - so I got another dizzy from the salvage yard, the pickup coils ohm out like they should as does the ignition coil. and I bought a brand new condenser for it as the old one tested bad. and when I first got the dizzy i put it in and it fired right up and ran for a couple days, then began doing it again. I went back to the salvage yard and grabbed another one that tested good, and when I put it in it fired up the first time but then shut off and has not started since.
But is it possible for the distributor to still be the problem even though the coils test ok? the shaft doesn't have any play in it, and the air gaps are within spec. I can barely get a .2mm between them. I also grabbed a couple of igniters while I was there. When I get it to run it may die when its cold and give me a code 14.
So from there I'm down to testing the distributor circuit, and the starter signal circuit, and the ECU. What is the best way to go about testing this to be Certain of what I need to go buy instead of just replacing stuff.
I have been checking on the automotive forums for Suburban no start problems and have tried some of the solutions, but my vehicle still doesn't start. Here is where I'm at: I have spark, fuel pressure at the throttle body, the fuel pump in the tank is working, new cap, rotor, coil, module, fuel filter, and ECM.
I just ran the truck 2 days ago for 10 minutes to flush the radiator, turned it off to install a new t/stat, then it wouldn't start again. I have tried starting fluid, gasoline, it cranks but no fire, not even a sputter. The pump has been replaced probably 9 years ago. The only other thing not replaced is the pickup coil in the distributor, although the distributor was rebuilt about 10 to 12 years ago. This vehicle just sits until needed, can't afford to drive it daily. The truck is a 1987 Suburban 1/2 ton 350K engine, automatic, 4wd.
96 sebring 2.5l v6 non-convertibleRan terribly for 12 blocks when I bought it, then died and wouldn't start.Bought it because friend said that mechanic had told him it just needed the head gasket changedReplaced the head gasket then it would crank but not start
checked, getting spark and compression on all 6 cylindersreplaced:-ecm-crank position sensor-combination distributor/camshaft position sensor/coil-flushed fuel system and replaced gas. checked everywhere for possibly misconnected wires and possible misconnected vacuum tubes, they are all triple checked ok. Checked the timing about a dozen times. Checked for misaligned timing sprockets, all ok, no sheared keyways, valves open and close at appropriate times / correct order and crankshaft timing mark matches cyl 1 position.
Fuel pressure is great.Turns over but doesn't fire at all.
About a month ago my 2002 accent started intermittently turning on. The car cranks nice and strong when it doesn't start-(until the battery loses too much power from repeated cranking). When it does start, it happens instantaneous, no issues no hard start.
I have talked to multiple people with varying amounts of automotive experience, who have given many things to try.
Things I've replaced or tested, hoping they were an issue:
-Starter and relay
-Fuel pump and filter, as well as relay for pump.
-Battery, post connectors and wires to starter
-Alternator and belt
-Multimeter tested fuel injectors and ran fuel system cleaner for last 3 fill ups
-Replaced spark plugs and wires
-Ran fuel line antifreeze every 2 tanks or so
Things I've been told might contribute to the intermittent starting, but haven't looked into
-Inconsistent fuel pressure
-water in the fuel tank
-Bad ignition switch
-MAF sensor
I live in area, currently in the icy grip of winter. I thought the cold would be a huge contributing factor, but alas, when the car has fired up the temperature has ranged from 1 to -32 degrees and has no issues starting in the deep cold.
Having an issue with my 2007 Santa Fe 3.3L. When the engine is cold, been sitting for a few hours not when the temp outside is cold, it takes about 5 to 8 cranks before the engine will fire. I can then shut it off immediately and start it again and it will fire right up.
I currently have the P0464, P0463 and P2068 check engine error codes for the fuel level sensor units. I don't really know if these are directly related as I've had them for about 6 months and the starting issue has just shown up the last month or so. Plus, I would assume these should only be related to sending fuel level information to the fuel gauge. Either way, I'm still leaning toward a fuel delivery issue since it only has a hard time starting when the car has been sitting for a few hours. I don't know if maybe it's the fuel pump or a electrical component. If it's the fuel pump, I'd like to do that when I take care of the sending units so I don't have to go back in. I've tried turning the car to the 'on" position for about 10 seconds without starting it to see if I could get the pump to load the line, if that's the issue, but it doesn't seem to make a difference.
The battery is good. It tested 12.5v after sitting over night.
I have a 2001 mustang convertible in good cond. A 6cly that I have had very little trouble with over the past year. I put in a new battery then, just after I bought it from a dealer. The dealer had gone over it with fluids etc. and I had a friend look it over when I bought it. He said it was very clean and a good buy. So, last week I started having trouble starting it in the morning. It would crank but would not fire. I turned the key off, and then tried again, Same result, cranks but doesn't start. I turned it off again and being worried about draining the battery, I turned everything off, radio, heat and fan, lights. Then I tried to start it again and, it started. I'm thinking I need new plugs, but I ignored the problem and went to work.
A couple days later I was leaving the grocery store, turned the key and same thing again, cranks but doesn't fire. I knew what to do. Turned off everything and tried it again, it started. Ok, so now some repair, possible plugs, is on my priority list. I need to get this fixed before the bad winter weather comes. Yesterday, after a long day at work, I was ready to go home and I it happened again. This time it's terminal. No matter what I did I couldn't get it to fire. This morning it's sitting in the office parking lot and I need to deal with this today.
Could be plugs, could be the fuel pump. Before I call the dealer and pay 4x what I should for this, what do you think it could be? 3.8 6cly. The car is sitting on a slight incline, in the parking lot. Gravity pulls fuel from the engine to the gas tank, if a fuel pump is going bad this could be why I can't get it to start. I'm going to roll it to a level area and hit it with starting fluid to determine if the pump is bad. I'll also pull a couple plugs.
Have starting problems some times, cranks over real good but will not fire . When this happens i have no fuel pres. But after it starts then it will run good This problem usually happens first thing in the morning. Is there a fuel pump relay in this system or do i have a bad pump . I only have 85,000 miles on this truck.
View 6 RepliesMy 95 Honda accord 4 cy. vtech, will turn over but not will start, you can try unlimited times and it just cranks, but no fire or start.... UNLESS I wait about 30 seconds first. In this time what happens is, for 15 seconds the usual dash lights are on, including check engine light, at 16 seconds the D4 green transmission light starts to flash rapidly. At 30 seconds the main relay can be heard to finally click in, and the fuel pump whirs and primes the fuel system for 1.5 seconds and immediately the check engine light turns off, the D4 light turns off, and the fuel pump also stops whirring. AT this point, at any time from here on out, (until you turn the car off again) you can turn the key the rest of the way to start, and the engine cranks over and now immediately starts right up!
Sometimes all the above happens just as described, but the D4 transmission position light does not start to flash. Everything else happens the same way and timing and after 30 seconds the car will start. NOTES: a. The obd trouble codes do not flash any codes when the jumper is put in place to read the codes. b. I have removed and checked the main relay, looked ok, and just in case I re-soldered all connections on the main relay board. c.the car drives and shifts fine. d. The time frames are exactly the same every time. Electronically perfectly the same, like the computer finally decides, OK go ahead and work now. Or like the car is attempting by some programmed response to say that something is wrong and needs attention.
I have a 03 xc90 t6 came out of work the other day and it wouldn't start replaced spark plugs, both cam sensors, crank sensor. After doing all that it sounds like it wants to fire now but doesnt.
View 1 RepliesHere is what happened. Pulled into gas station and car just died. Tried to restart and no fire. Cranks but no fire. Flat bed trip home and started to diagnose. Thought it was a bad fuel pump so I pulled and tested with a direct power and functions fine. Checked all fuses and relays, all seemed fine. checked for power at pump and nothing. Reset cut off switch and still nothing. Thought maybe ECM relay in the under hood fuse box was bad I borrowed the one out of a friends car. Nothing. Thinking ECM was bad put theirs in my car and got power to pump. So I put their car back together thinking mine was the ECM, then theirs won't start. The ECM relay i took from there car and put in mine blew when i tried to start my car. Got another ECM for my car and put in. Still no power at the pump. Here is the info about the car. 2001 Santa fe 2.4L auto. 80,000 miles. Timing belt, tensioner and all Idler wheels changed along with water pump at 71,000 miles. This car has been very reliable up till this point. No check engine light came on at any time..
View 8 RepliesMy father in law has a 98 4wd, 4.0L that cranks but doesn't fire. We pulled a plug to check for spark....no spark. Possibly coil pack, or crank position sensor?
View 5 RepliesI have a 1995 ranger with a 4.0 it cranks just fine wont fire has alot of fuel spark it will crank and crack then it stop and acts like it is going to fire up and stops cranking... This thing has 253k on it...
View 4 Replies