Passat (B5) :: 2003 - Engine Stalls Won't Run
Jul 17, 2011
I had this issue about two months back when I first got my 2003 Passat 1.8T and haven't had it since. Basically, when I start the car, it'll turn on fine, then it will idle out and die. Or, it will rev up a little and fluctuate for a couple seconds before finally dying. This has happened only at night for the past two weeks. It would run perfectly fine otherwise. This morning, I try starting it and it would die right after. I tried starting it a few different times, and it would finally stay on, but as soon as I put it in Drive, it would die. The engine sounds quieter than normal.
I can go record a video of exactly what it's doing if it's worth your time. I really need to get this working as I have a million things I need done today. I have a VAG-COM and the only codes are for intermittent misfires on Cyl 2,3,4. I've replaced all four spark plugs recently and just had the oil changed as well as the air filter.
Also, one more thing, I used to be able to remove the black plastic tubing that goes from the grill to the air filter and it would run fine for a while, but that's not fixing the issue now.
View 3 Replies
Advertisement
One of my friends recently asked me to change the timing belt on his 2004 Passat 1.8T. I put on everything as instructed by the manual that the parts department gave me. However, when I start the engine, it runs perfectly for about three seconds, then starts rattling, and stalls out. I took the belt off and put it back on three times and yet, it still continues. This rattling seems to be coming somewhere from within the exhaust system near the engine and sounds like a back-fire. The check engine light also appears when this begins happening. I replaced everything, water pump, pully, tensioner, and etc. Note, I am a professional mechanic and have worked on several Volkswagen cars, including my own, but I never encountered a problem like this one.
View 7 Replies
Passat B6, 2009 TDI CR, 140 bhp, DSG.
Having an issue that's bugging me. all cold starts are fine. However, if I drive a short distance then try to restart the engine cranks, sounds like it catches but stalls.
It takes 2-4 retries to get it going, i'm not releasing the key too early as this happens even when I hold the key in.
I've not been able to get a VAG-COM on it yet but would like to know whether this is likely to be something simple or, if it's time to sell the car?
View 2 Replies
When I am slowing to a stop, my engine idle gets really low (like 500rpm or less) and sometime stalls. At the same time, the oil light comes on. It does this all the time, and yes I've had my oil changed recently and actually I just checked it the other day and it was fine (along with all other fluids).
I've had the mechanic take a look at this three times and every time something gets fixed but this problem remains. They now say it's a ghost. It is not the air intake (I've had all of the hoses checked and a bad one replaced). It's not the electrical (I've had the spark plugs and cables replaced about a year and a half ago).
I've pretty much had everything that a car of a certain age needs done fixed/replaced in the past year or so, and I still can't figure out what could be causing this. A recent show had a similar problem, but the gal didn't mention the low idle/stalling. In that show they mentioned that she should have the oil pressure gauge checked or replaced, but would that cause the low idle/stalling? I don't know what to do and I'm very reluctant to go to a dealer.
View 19 Replies
have had many problems with my 2003 Accent. I am not a mechanic, but I suspect the problems are related. My engine sometimes stalls when I sit at a red light. I drive about twenty miles to work. On a good day it will just sputter occasionally. On a bad day it will stall as many as three times. It also frequently "skips" a little while driving. It's like a split second hiccup in engine power.
I also used to have a really hard time filling the gas tank. It would take about fifteen minutes when close to empty. I have had it worked on three times over the past three weeks. First they replaced the timing belt (which I already knew needed to be replaced). Then they replaced something called a charcoal canister and blew out all the vapor vents(?) ( Again, I am not a mechanic). After that the car ran ok for about two days, and I can now fill the tank in about two minutes. But, it began stalling again, just as bad as before. So, they replaced something called a MAP sensor (MAFF?).
It has been a couple of days and the car hasn't stalled . . . yet. However, it still skips occasionally while driving, and my engine light has come on again. The mechanic says the code has something to do with a barometric pressure problem. what might be wrong with it?
View 2 Replies
I've got a 1997 F250 with a transmission problem that I've been trying to diagnose. The problem is I can't grab any codes from the truck. I took her to the transmission shop and they described to me the same problem I was having. Whenever I try reading codes with the engine off it fails, when I try reading codes with the engine on it stalls the engine. The transmission shop referred me to another shop that might be able to figure my problem out, but I'd like to leave that as a last resort. I've checked all fuses and relays and I have a new engine computer on order right now. However, I'd like to know if there are any other possibilities.
View 1 Replies
2003 NISSAN Xterra
Problem started a couple of days ago. While driving the car normally it suddenly stopped. I was able to restart it but it turned off again 60 seconds later. This has gone on with the engine running from 10 minutes to 10 seconds. The battery terminals and all cables are clean. Distributor cap and rotors have been cleaned. Fuel pump replaced last night. I still get the problem. Error codes listed were: P0328 - Pre Detonation (knock sensor) Bank 1 causes could be restricted fuel - over temp engine. Now this error has been coming up for five years and I've replaced the sensor numerous times. P0732 - Gear 2 Incorrect RatioP0102 - Mass Air Flow Low InputP1148 - Closed Loop Control Function, BANK 1P0420 - Catalytic Convertor, BANK 1P0134 - O2 Sensor No Activity, BANK 1
Regarding Fuel Starvation - NOPE, Engine Too Hot (it wasn't), Second Gear Not Within Ratio (never had gear problems), Knock Sensor and most error codes have been related to bank one. Error codes on car computer were erased and engine is still hesitating slightly and stopping. Just checked Mass Airflow Sensor and it looks clean.
View 8 Replies
I have a 2002 F250 7.3 4WD automatic with 313,000 miles. A week ago it started stalling after it idled for 10 minutes. It acted like it wasn't getting fuel. It would sputter a few times then just quit. I changed the fuel filter and the truck ran fine the rest of the day. Since that day, it has acted the same way every morning at 1st startup. It idles fine for 10-20 minutes (depending on how cold it is outside), then hesitates a little, then stops. After going through 3 new fuel filters (thinking I had bad fuel), I stopped putting in a new filter every morning, and found that if I just waited 4 or 5 minutes, it would start and run fine after that. It then runs fine the rest of the day.
After it stalls, it will not start right away. I need to wait a few minutes. I've tried draining the fuel filter bowl also. No luck. I tried a new Cam Positioning Sensor. It seems to be related to temperature. It's been getting down to 30 degrees Fahrenheit the past few mornings. It starts fine and idles fine until the temp gauge just starts to move. Then, the stall happens. My fill-up just prior to this happening was with B20 Bio Diesel. I suspected that for a while. But, I've ran all that fuel through plus 4 or 5 regular diesel tanks through, so I no longer think it was related to that. It do see the check engine light when it stalls. I had a shop read my codes and the only code was bad KAM memory. The mechanic said that code shows up all the time on these engines and not to worry about it.
View 14 Replies
As the title says, I have an 02 Supercrew with the 5.4. The engine starts when cold and runs fine but sometimes when I start it hot after running for a bit, it will stall out unless I keep my foot on the gas pedal. This seems to only happen on hot days. It was about 90 F here yesterday and I drove it to a shopping mall after supper - maybe 5 miles. It sat for maybe 20 minutes and when I re-started it, it stalled out.
The tach needle just drops slowly to zero and the engine stops. It will re-start without any problem but will only keep running if I keep my foot on the gas and keep the revs up a bit. It has done this a few times in the past few years and only on hot days after it has been running and then sat for a few minutes.
What I should look at? It does not throw any codes and generally runs ok after a few minutes. For example, last night I managed to keep it going by shifting into neutral when required until I got back on the road. I drove 2 or 3 miles and at the next light, it acted like nothing happened.
View 1 Replies
I recently purchased this 2003 F350 DRW with the 7.3L, automatic trans. Truck has 140k on it. Three times now while the truck has been idling, the engine just died. The first time was a couple of weeks ago when I was pulling out of the driveway. Then again yesterday twice, once while just sitting at a stop sign. Each time it has started right up and ran fine.What is going on here?
View 1 Replies
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
View 14 Replies
I have a 2001 Ford Excursion Limited 7.3l with 199,980 miles on it.
It has a TS-6. My first problem is that when I come to a stop or slow down to a crawl then press the accelerator the engine stalls and dies. I have looked and looked at threads and can not find this example anywhere. There is no pressing the pedal and it remains at idle. It dies, shuts off, quiets. I have thought icp, tps, ivs
Second problem is that a/c is blowing hot. Other than being out of Freon, what could be other things to check. It does sometime go to default, but has done so in awhile. It does not blow cold in rear and hot in front. They both blow hot. I have replaced the pvh sensor.
View 1 Replies
2006, 2G, 43000K. This has happened twice now. Both times on an extended trip of 3+ hours in hot weather: Cruising along at about 70 MPH, the engine just quits. RED Triangle; check engine light; and vcs light. Turned everything off. Car would not restart right away, but after waiting 15 minutes or so, the car restarts and runs fine. All warning lights off except check engine light.
Immediately drove to a Toyota dealership where the following codes were found: P0AOF info 204 (Engine failed to start); and P3190 (poor engine power). The Tech checked the EFI relay; checked for oil puddled in intake; and checked for a contaminated MAF sensor. "No problems found"!
View 7 Replies
I have a 2000 Passat 1.8T 5spd that today started stalling out. I start it up and it idles fine but when I go to give it gas, it stalls out at around 1600 RPM. My guess is that the Fuel pump may be bad, or i have got bad plugs or coils. It was running fine this morning but it just started doing this around an hour ago.
View 7 Replies
I have a 00 Passat GLS.
When i accelerate, whether it's hot/cold/wet/dry outside, the car almost stalls. I have not had it stall yet, usually out of pure fear, i drop the pedal to the floor, and i catches up. I have had this happen at very inopportune times, like joining traffic. The car does a sort of stutter step.
I know little about new cars, but i feel like the fuel or air aren't making it through nicely.
View 4 Replies
I own a 2002 Passat 1.8T and have had a check engine light for the past month or so. I was finally able to get it to one of my local mechanics who specializes in german made cars. He showed me where one of my vacuum lines had split open, then proceeded to splice the line with a t-fitting and a new length of hose and then reset the check engine light.
Well, the engine light has stayed off, but now when I start the car, it almost stalls out right after startup, then proceeds to idle and run fine. The mechanic thinks that since the car was running for so long with that vacuum leak that the ECU needs to to "reset" itself to the different pressure.
View 1 Replies
So I washed my car today at one of those do it your self washes, about 1/2 mile down the road my car stalls, and wouldn't start back up until maybe the 6th or 7th try, my thought was I got something wet...
View 3 Replies
I've had this intermittent issue for a while where the car won't start properly. What seems to happen to me is that it starts properly, but then immediately stalls. Normally during a start it will start at about 1200rpm then quickly idle back to under 1000 and then slowly reduce some more. Now at about the same time as I would expect it to idle back to 1000rpm it stalls. After this happens, it seems like I can keep reproducing the failed start over and over again if I try to start the car again. If I wait 30 seconds or so and then try to start it, it usually works.
On two or three occasions I got a warning on the dash about faulty steering lock. Checking in VAG the only errors shown are related to those, no other codes. This has happened many times over the course of perhaps two months. It's been colder during this period, but generally it seems the error happens more often when its a little warmer weather and not really cold. Lately I've been inserting the key part way, waiting a few instants for things to initialize and then starting and it seems to work every time.
View 2 Replies
Car has 6600 miles on it and is back in the shop for 2nd time to determine what is wrong. Basically, the car starts and then stalls out after a few seconds. It will not start again (at least with me). Course, the dealer can get it started after the tow to them.It began in April after an oil change at the dealer. A week after the change, it started up and then a message SHUT DOWN appeared on the dash.
The car stalled and would not restart. When it was towed to the dealer, it had no oil. Per the dealer, there was no leak and it was assumed the tech forgot to put oil in it, They indicated it was not a problem since there was some oil remaining but the car would still not start. They kept it a few days and replaced the relay for the fuel modulator, electronic fuel pump, fuel unit, fuel pump control unit, e-control unit and of course the battery. Note: this was a cold start.
About a month later, I had driven the car for about 30 minutes, left it for an hour and came back to the car.....it stalled again right after start up and would not restart. After being on hold with roadside assistance for awhile, I tried it again and it started without issue. .
A week later (today), used it for a half hour, came back to use it 3 hours later and same story. Started, then stalled, no restart. Towed it to the dealer and the tech got it started but no codes telling him what is wrong.
View 5 Replies
I bought a 2003 Passat used from a after market dealer when it came off lease. Within a few days the engine light came on. I took it back to the dealer's mechanic, and he just hooked it up to the diagnostic meter and cleared the code and the light when off. He told me not to worry about it - I probably didn't close the gas tank cap right.
Sure enough two days later - it came back on - and I took it back. The mechanic had it in his shop for 6 hours. I picked it up, and now there is no light at all. Its the only light that has been affected.
The engine light does not even come on when you first turn the key in the ignition. I think the mechanic has purposefully did something to either the fuses or the wiring. [URL]
View 4 Replies
Just purchased a 99 passat v6 and it has a low idle surge and stalls when coming to a stop.It runs fine until it heats up about 15 min. then it surges up and down and stalls.
View 1 Replies
