Passat (B5) :: 2002 - Engine Cut Out And Car Is Dead - Cranked Sensor
Jan 20, 2008
My 2000 2.5 V6 TDI Passat has just died.. was doing 60-70 and went to change gear and the engine cut out, tried to restart and its just cranking over and over. Did have a message on the display and the glow plug light on when i was coasting something about management but didn't get the whole message, wasn't on for long.
The recovery guy reckons it might be the crank sensor.
The cambelt should have loads of miles and time left before it goes.
I'd like to sort this myself or at least be sure of what the problem is before i take it anywhere, so what to check for?
There's fuel in the filter and it turns over fine (it could be my paranoia but maybe cranking a little fast)
i just changed a CV joint to fix one problem yesterday, this is the last thing i need!
View 7 Replies
Advertisement
This 2005 LeSabre with a 3.8 v-6 ran fine but had a marginal battery. Then the key got left on overnight leaving the battery totally dead. After jumping the battery and letting it charge, the engine cranked fine but refused to start. Haven't had a chance to check for fuel or spark. Why would a dead battery trigger this no start condition?
View 2 Replies
I have a 2000 Silverado Z71 with a 4.8 and Auto Trans. Here lately if the truck sits for more than a day with out being cranked the battery is dead. Put a new battery in last July. When i put a meter on it the Alt. shows 14 volts out put. once it is cranked it will start every time with no problem.
View 1 Replies
Well it looks like the passenger side door sensor is dead since the MFD shows the door wide open.
Where the actual sensor is since I don't really see anything around the door.
View 1 Replies
After a long hour working day, B6 could not start in company's parking lot. The temperature is not cold, the battery is not dead, has plenty gas in the tank. The starter cranked but couldn't start the engine. What should I try? Change the starter? if i need parts, I will grab from store and try to fix it in parking lot. if not, I have to tow it to dealer tomorrow.
View 13 Replies
My 2009 Camry check engine light is on. Dealer said the two O2 sensor both are dead and need to replace. After dealer reset the check engine light I have driven two days for 50 miles and the check engine light doesn't come back. If the O2 sensor is bad how long does it take for check engine light on again? Is it possible the check engine report on by mistake since two O2 sensors got bad at the exact same time is really rare.
View 13 Replies
My daugther 2002 Volvo V50 blow an engine because of the time belt slipped She had only had less than 75000 and was relgious about her mx checkups timely and by only Volvo Mechanics. She is a Service member in Gemany and the Germany dealer say there is nothing she can do. How to get this engine replaced or even credit for a new volvo. The Engine is gone and the mechanic said 7000 Euro. The car blue book at 9500 Euro.
View 10 Replies
Got in the car today, 2002 SC430, turned the key, car cranked and cranked but no start. I'm guessing I'm not getting fuel. How do I troubleshoot?
View 6 Replies
I have a 2002 GLX Wagon 2.8 30v, and was getting Cat warm up threshold low code, on the driver side due to the cat being bad. As a temp fix I decided to use spark plug haulers to gap the sensor. When I removed the O2 sensor I wiped the dirt off with a paper towel, which was clean and dry. I put the sensor back on, but now I am getting 4 codes which won't go away. p0036 p0056 p0141 p0161. These are O2 heater circuit codes both bank 1 and 2. I did not touch bank 2 so I don't know how I could have caused this error. I tried to take off bank 2 sensor but it is really stuck on there.
View 3 Replies
So a letter history about the car and this car is a friends car. They owned the car and drove without changing the timing belt when the car hit 109k. So the timing belt snapped and they went out and bought a timing belt and also the timing belt kit with the pulleys and all. They installed it.. didnt turn over or what so ever.
They towed the car to us which we own an auto repair shop. We knew the valves was bent and so we tore off the heads send them off to have them put new valves and etc etc.. We put the car back together for them and now the car runs fine. They pick it up and about a few days later they brought it back due to a check engine. It threw the code:
16711 - Knock sensor 1-G61 Signal too low. (p0327)
now we replaced both knock sensors and when they came and got the car... the check engine light came back one showing the same code. We cleared it out and the next day it came back on showing the same code Again! So now we don't have a clue why that code keeps coming up because we replaced both sensors with a new one. Any clue why the code keeps popping back up?
View 1 Replies
Got the CEL Bank 1 Sensor 2 heater circuit fault. Is that the rear right post-cat oxygen sensor? What is correct part number or possibly a link? 2002 2.8l Passat V6...
View 3 Replies
The dealer recently replaced the front and side motor supports. Since then I've noticed that the car idles high when first cranked and I smelled excessive exhaust fumes. One time it idled really high and would not idle down when I hit the gas. Then it started idling up and down when my foot was not on the gas. Could there be any connection between this and the motor support installation? Could linkage to the gas pedal have been bent during installation? 2002 6 cylinder Honda Accord EX.....
View 3 Replies
Went out to the garage to move the car ('03 GLS V6)...cranked over, almost started then died. When i tried to start again, the engine seems to crank over too easily...like NO COMPRESSION, and it is puffing smoke out the tailpipe. Did the timing belt just let go? The car has 68K.
View 4 Replies
2002 Subaru Forester I took my car to the Auto Zone to read a check engine code. It came back as being a "knock sensor". Besides that I needed a battery, and when the guy was putting it in he said my engine was moving too much and that I probably needed motor mounts.
I was looking at a discussion back in 2010 and the Subaru specialist told the person needing motor mounts is rare for a Subaru, is that true? I'm taking it to a mechanic, what should I expect? how many motor mounts does a subaru have?
View 7 Replies
I had a problem recently with my '11 SE. It only did it once and hasn't done it since. I pushed the START button and the engine cranked over but it never started. I let it crank for about 5 seconds before I pushed the switch again to make it stop. The next time I pushed the START button the engine started.
View 5 Replies
I had a check engine light pop up and I went and got it checked out. Comes to be its a IAT sensor or bad connection with this sensor. I change the sensor and made sure the wires on it is all good. The question is, I still have the check engine light up, does the code need to be deleted? And what happens if the code gets deleted and problem is not fixed?
View 3 Replies
2002 ford sport trac.I have been having an ongoing issue that started with the engine cranking but would not turn over until an hour passed. After replacing multiple parts (cam shaft sensor, crankshaft sensor, ignition pack) I am now down to poor fuel economy as the last of the issues (roughly 12 in the city and 15 highway). I was told the issue may be the engine coolant temperature sensor going bad so I decided to replace it. I found this was very difficult due to it being a plug and locking pin design and in a very tight spot in the engine.
I tried to purchase a replacement and the parts store kept trying to insist on selling me a part with threading. I finally found someone that figured out the issue and found the part for the 2001 sport trac had the same plug style with clip that did fit but was shaped a little different on the sensor end which I assume was due to being aftermarket. I noticed that there were two plugs side by side and the one easiest to access was on the left and I was told the one on the right was the sensor that gave the temperature reading to the gauge.
After installing the engine coolant temperature sensor I found the temperature gauge on the dash now will not respond and is sitting below the cold end of the gauge completely off. Is it possible this is because the part was for a 2001? Is the sensor on the left (passenger side) the engine coolant sensor?I would hate to put the old sensor back in just to test if that's the issue due how difficult it was to put that locking pin back on. What to check that could resolve the gauge issue before pulling this sensor back out?
View 3 Replies
Been having issues lately. Like I open the door and lights inside won't come on until the engine is cranked. Clock on dash resets. Then just yesterday I go to start it and get nothing. Checked battery connection and they are tight. What it could be. It's at the dealer being checked out. Probably will get the dreaded couldn't reproduce the problem.
View 1 Replies
I got this problem for 10 days and by the time to take my car to the auto shop it turned out that now I cannot start the engine at all. I started to hear that the starter is still running for a second or two after I switch on the engine but I was busy and was not able to leave the car for a check. Well, this morning the car gave up and refused to start at all.
Before I blame the starter I was thinking about the ignition lock although I didn't noticed anything problematic with it. I think that the battery is OK since I didn't lost the radio and I still can operate the windows as well.
View 9 Replies
Had an odd situation earlier tonight. The starter cranked normally but the engine wouldn't actually start. I let it go for 10 seconds and hit the button again to make it stop in order to protect the battery. A few seconds later, I tried and it fired right up without a hitch. The MIL never came on so no codes most likely.
Car has 17k on it. 2013 2.0
View 6 Replies
I am currently hearing the engine noise. Recently I have replaced my front O2 sensor which I don't think would cause this ticking noise but I figure I should include that info. I already had my cams replaced due to a bad follower. I had my belts and water pump done at 80k I'm currently at 130k. I threw a coolant system code a few days ago, which is odd to me, my temp gauge stays at the same temp it's always shown.
View 6 Replies
