Passat (B5) :: 2001 With Airbag / Flashing Oil / Brake / ABS Lights And No Tach
Nov 6, 2011
So I have a 1.8 5spd wagon which flooded out the comfort control module. I got another CCM but I still have a flashing oil pressure light. a flashing brake warning, a solid ABS light and an airbag light. The tach doesn't work and the MFD only occasionally works. Before I replace the ABS module I would like to eliminate anything else that might be in common with all these systems, is there a hidden fuse anywhere or a relay?
I tried unplugging the ABS module and it didn't change anything, do I need to code the CCM it has the same numbers on it but even after replacement the power windows still don't work even though the door locks, mirrors, and dome light on all but the drivers door ( I assume the micro switch is bad)work now, also the car starts.
View 4 Replies
Advertisement
So my girlfriends passat is starting to have some problems. It looks like a light show on the dash. When driving it, every now and then (a lot more now) the tach goes dead, and the oil and brake light flash, and it starts beeping. The car also has a ABS light on but that has been on for a long time.
So far I've checked both the oil and brake fluid levels, and checked all the fuses. Everything is good there. It just seems funny that they all go at once. I figure maybe one of the plugs to the cluster is loose giving everything a zero reading? I need to buy a vag cable and software some time that's for sure.
View 6 Replies
I have a 99 passat that the oil light will flash and the tach is inop then out of the the blue it stars working. was wondering if any 1 has had this issue. I checked the wiring didn't find no bad wires and i tried another cluster same thing.
View 1 Replies
I have a 2002 Elantra and all of the TCM, ABS, AIR BAG and BRAKE lights come on as soon as I push the throtle and the car starts moving forward. I looked inside the owner's manual but all it says is that if all these lights come on at the same time and stay on the car needs to be taken to the dealership ASAP.
View 4 Replies
I have a 99 Passat; 5-speed V6. My tachometer would go out intermittently and at the same time the oil and brake light would start flashing and the ABS light would come on solid. There would be no noticeable difference in performance. When the tachometer would come back on line the lights would go go. Now the tachometer appears to be down permanently and the dash lights above are in the same state as above. Still no noticable difference in performance. What may be wrong?
View 3 Replies
I took my 2000 passat 1.8t to a couple of places and both say that my abs and brakes are fine even though there is a flashing light that says brake lights failure and abs light. The brake lights do work. Is there a way for me to clear the code?
View 4 Replies
My alternator went today, driving and the battery came on .. was concerned but was still on my way, abt 5 miles from my house the abs light and brake lights starting flashing and beeping .. and then caput .. the car shuts off .. figured it was the alternator, cuz thats whats logically made sense .. talk to vwvortex and if so how much do these type of jobs cost ??
View 18 Replies
Had a small brake fluid leak from my right-rear wheel, so I took it into a local place called Wheel Works. They said the right-rear caliper needed to be replaced, so I told them to go ahead.
Two days after I pick up the car, the ABS light and brake warning lights start flashing intermittently. They'd come on at random times, and then turn back off. After about 2 weeks of this, the warning lights are now on all the time.
I've read elsewhere on these forums that the ABS module on our cars can go bad and might need to be rebuilt. But is it possible that the mechanic caused this problem when he was working on the brakes to replace my caliper? Could it be something more minor than the ABS module? I now have reason to believe this mechanic is shady, so I'm hesitant to bring it back there.
View 6 Replies
Just bought 01 passat wagon 2.8 v6 and my abs light is on as well as the brake light.
View 8 Replies
2001 01 1.8t... Hoping this isn't a bad ABS module. When I bought the car, I was told it was a bad wheel sensor in the drivers side. But, the funny part about this is its not on all the time, sometimes it doesn't even come on and the dash is normal.
View 3 Replies
i have a 2001 Passat & my ABS & Brake warning lights have come on with no other symptoms. Brakes work fine - local mechanic can find nothing wrong!!
View 2 Replies
My new to me 2001 Prius has a slowly flashing Airbag light. Reading this handy forum I found that by jumping two pins on the OBD port I could read the codes generated by the flashing lights. I did that, and have a 3233 and 4448. The car runs and drives fine, fluids are all good etc. Can the codes be cleared and see if they return?
View 5 Replies
MY friends's 2001 Passat has an issue. Brake lights work fine when the headlight switch is turned off. When she turns the headlight switch ON, her brake lights are stuck on. Left, right, and center. What could this be? Seems like maybe a fuse or brake light switch.
View 2 Replies
My case involves a 2005 Prius with 55k miles on it with the problem of the master warning light (triangle with !), yellow brake light ( (!) ), airbag, and VSC lights coming on whilst driving. The car drives just perfectly fine without any discernible problems. Scan tool did not detect any codes. Tested the 12v auxiliary battery and it is strong with both voltage and amperage (even went as far as temporarily jury-rigging a fresh v12 battery in parallel with it to see if it would alleviate the problem). Inverter coolant pump runs well, coolant changed with appropriate Toyota Super Long Life coolant (50/50 mix) and system bled. Despite some drivers' concerns over disconnecting the 12v battery to reset the lights, this was done and the lights would go out, only to have them come on again after about 5-10 minutes of driving. Asides from the lights coming up, the car itself seems to be asymptomatic. Hybrid system appears to be running smooth and fine, SOC is good, asides from the lights the car drives very well.
View 9 Replies
I bought this prius and it runs and drives great, no issues until a couple weeks into ownership and the car refused to "ready" up. i figured out real quick it was the 12v battery....BUT instead of replacing it i was trying to be cheap and charged it to verify for sure, worked great for about a week until it wouldn't start the car again and gave me the "park on level ground" warning. i got passed it after a few presses of the start button but the master warning, VSC, Brake (!), and airbag lights came on. I replaced the 12v promptly and this did not remove the lights. 2 weeks later the lights are still there and I have tried resetting the brake/airbag lights via pins 4 and 13 and failed at getting the lights to go out. a scan tool will delete them for about 10 seconds.
The codes I was able to pull via blink were:
(!) 11
ABS 42
VSC 51 45
airbag 23
I cleared them with the "press brakes 8 times" method, lights remain and codes pop up
VSC 51
airbag 55 57 23
View 13 Replies
whenever i start my car the abs and airbag lights comes on and stays on at 1st it used to be the abs light only then sometimes while driving it would go off and then comes on back. but now its both the abs and air bag lights that comes and the abs goes off from time to time but not the air bag ...
View 2 Replies
I own a 2004 Toyota Camry. Its just under 100,000 miles. A few days ago the ABS and brake lights started flashing on and off at the same time. They stay on for a second and then go off. It doesn't happen every time I drive the car but it is happening more than it's not. The place my husband took it to said they can't diagnose the problem unless the lights stay on. Is it safe to drive the car?
View 3 Replies
So my brake light was flashing and my abs light and traction light came on...i got codes for a faulty abs module and G85 steering angle sensor. I replaced the module and I cleared the codes and they cleared except the steering angle sensor and now the traction light is stuck on? Do i have to zero point calibrate with a vagcom?
View 4 Replies
I went to a stereo shop to have all my doors covered with DynaMat. They did a great job there but now I have an airbag error. How do I reset this? I do have a VCDS cable. I know it was because the battery was not unplugged before the door trim was removed so I'm not that worried, just wondering if VCDS can take care of it or I MUST go to the dealer.
My other issue are the interior lights. I had them all replaced with LED bulbs and when I left the shop I turned the map lights on and all was good. I left the shop to put some fuel in and when I started the car again I had no lights. Now NONE of my interior lights go on. What Happened? I've seen plenty of people with LED bulbs in their cars so I didn't think anything could go wrong? Do I just go back to the stock bulbs?
View 17 Replies
so I just installed a set of sportline seats and after the fact I have a parking brake light (no auto hold) and airbag light on. After checking fault codes in vag, I have determined that both these lights are due to the air bags.
My question is this, can I add resistors to the airbag wires in the new seats to trick the car into thinking that these are the old airbags? Everything else except memory works on the seats, just these damn airbag/parking brake lights.
View 6 Replies
I have a stock '13 GTI with halogens and standard (non-LED) tails.
In VCDS, I coded the CECM to enable the brake light flashing under panic braking and also enabled the activation of hazard flashers under panic braking. Coding was accepted, no issues.
However when I did a driveby test yesterday with a friend watching, neither feature activated. I stomped on the brakes as hard as I could; ABS definitely engaged. So I was wondering a couple things:
Is there a minimum speed required before this will engage? I was probably going only about 35 mph when I hit the brakes.
Does this feature (at least the flashing brake light portion) require LED tails or will it work with the regular tails?
Looking on youtube videos of people who have activated this, it appears that they have both the flashing brake lights and flashing hazards activated at the same time so it would seem that's allowed by the CECM, yes?
Found a screen shot of the VCDS screen to show what I did:
I enabled BOTH bit 1 and bit 2. Some of the research I'm doing seems to hint that I should only be selecting one or the other?
View 6 Replies
