My cup holder sticks and will not come out like it should. I believe me brother had spilled some coke on accident. How to remove it. Or maybe give me a "how to" link they know about. I tried searching for this but, I could not find anything. I have a 2000 passat.
View 2 RepliesI'm trying to install an iPod dock inside the coin tray. How to remove the coin tray? The iPod dock fits in it perfectly width wise, but the length is a bit long so I need to remove it so I can drill a slot inside it.
View 4 RepliesI need to send my cup-holder cover and trash hook to Clay so he can color match my F650 dash and I can't figure out how to get the damn side clips on the cup-holder to let go!
I got the top clips and the bottom clip to let go but the side clips will not slip through the slots... I've been near the point of breaking them trying to slide them through...
What sort of trick do I need to perform in order to remove the cup holder that is on the front floor of my 2001 4-door Ranger. I'm hoping to be able to remove it without busting it to pieces.
View 4 RepliesI have a 2012 Prius V, and somehow A tin of Altoids has fallen behind the drawer, (hidden drawer) of the center console. How to remove the drawer to access behind it?
I can't see any catch or release to trigger releasing the drawer. I also think accessing it by opening up the whole console from the top is risky as the EV, ECO, and PWR mode buttons are wired into it.
I was wondering how do you remove the cup holder part of the console dose it just pop off or are there metal clips or screws hidden some how?
View 4 RepliesI'm doing an install on my son's 2000 passat V6 30 valve.
I have the front rad pulled out and there is plenty of room to work. How do I get off the viscous fan assembly. I removed the fan's 3-4 allen bolts, I now need to get the assembly out. I also removed one of the long allen bolts in the actual assembly. I have the fan ribbed pulley secured with an old serp belt and grip wrench. I am trying to losen the large nut behind he fan assembly. I have attached a photo to point of reference. I may have a manual next week yhat may explain all this.
I have recently inherited a 2000 Jetta. The car runs great however the plastic tube that holds the oil dipstick is broken in two or thee spots. It has been previously repaired with electrical/duct tape. Doesn't seem to leak but I'm wondering if I need to get a new one in there. Is this something I can do at home or does it need to go to a shop?
View 3 RepliesI'm sure that it comes to no one's surprise here that my clock on my 2001 Accent is not working properly. This seems to be a chronic problem with ALL Hyundais in the 2001-2004 era.
I have acquired a new clock, but I'm looking for some instructions on how to remove the centre dashboard on a 2001 Accent without breaking anything or accidentally disconnecting anything while removing it.
I see there are two screws in the pop out cup holder...once they are out what is the next best and safest procedure to work the dash off all the way to the top so I can replace the clock...and then get it all back together again?
2000 Volvo S70, 177K - This car is new to me, and shortly after purchasing it, I began having difficulty removing the ignition key when arriving at a destination. With the transmission in Park, and the engine shut off, the key just won't come out. Then again, sometimes there's no problem at all. Oddly, the problem seems to correlate with the cabin/engine temp. If I allow the car to cool off, then go back to it in a half hour, the key will usually come right out. Same thing with short trips. I'm fortunate so far that I've not been in any high crime areas where leaving the key would be risky; but I will need to solve this eventually.
I understand that there's a safety switch/sensor that ensures the vehicle is in Park before the key can be removed, and I've tried being a bit more "forceful" in shifting to P, but that doesn't seem to work. I'll be taking this to my mechanic anyway for a state safety inspection followup; are there any hints I can give him if I can't figure it out myself?
Is the temperature factor suggestive that the problem is in the transmission sensor? I'd prefer that the issue be a sensor or adjustment rather than in the ignition switch just to avoid the re-keying mess.
I need to replace the rotors and calipers on my 04 accent gl. I noticed there are 5 bolts on the back of the caliper. I know one is for the flex hose connection. Then there are 2 big hex bolts closest to the dust plate. Are those for the caliper mounting bracket? and if so will they need to be removed? Then the final two are on the outer edge, however the top one is rounded and rusted, is this normal? The one on the bottom is a hex. So what needs to be removed to change the rotors and pads? I also notice that there are two screw holes in the rotor, that I guess snug it in place against the hub, however the screws are missing. Is this bad? are they needed? and if so can I get new ones?
View 10 RepliesWithout vagcom?
View 8 RepliesHow to remove the air vents?? Center along with Drivers/passanger side. Bentley shows to use a trim tool/wedge and looks like they just pop out.
View 1 RepliesI wanted to know how to remove the shift knob from the 1.8t and yes its a 5 speed!..
View 2 RepliesRemoved the trnk emblem from passer sedan? I'm looking to spray it....
View 17 RepliesMy automatic door lock is making a buzzing noise when it locks the door. It does not make any noise when unlocking. I need to remove the door panel to take a look. How to remove the panel on the drivers door of a 2000 Dodge Grand Caravan?
View 4 RepliesWhat size socket is used to remove a lug nut on a 2000 F350 4X4?
View 6 RepliesI have to remove the outside door handle in order to make a repair on the door. I did remove the torx screw from the side of the door but still doesnt come out.
View 3 RepliesI have a 2004 1.8T 4Motion (automatic) that blew a CV joint boot. After inspection of the other side, I decided to replace both (just the outer boots). Got the axles out without much trouble but now I cannot drive the joints from the axles. I've tried both and neither is cooperating, I've knocked out off them with a mallet but they aren't budging. Is there something to do besides just driving them off?
Axles are tubes (hollow) p/n's 8D0 407 271 (& 272) ED.
First of all... do I need to remove both, the restraining bolt AND nut to remove the tie rod end... if yes, than this bolt seized, the nut is easy but even if I punch the bolt it wont move... ??
View 4 RepliesRemove or replace the tail lights on a B6 wagon? I'm changing mine out tomorrow with the new smoked tail lights and was wondering if there's anything I should know ahead of time. Or even a step by step order to removing them.
View 4 Replies