This is a 2000 Passat GLS 1.8 turbo that is in great shape and loaded. It recently had all new tires, brakes, belts, and tune up 98,000 miles. Now the not so good, after died while driving it was taken to the garage and the mechanic told us it needed a new camshaft and timing chain. I didn't have the money to start dumping into the car so I am stuck in limbo.
View 9 RepliesCan you change the tensioners and guides without removing the chains or getting the cam lock tools ? Doing a in truck repair to fix a squeal sorta noise at start up without the belt on coming from passenger side valve cover that lasts for about 5 sec. oh fyi CRC new freeze off works wonders compared to jb blaster for my tear down so far!
View 6 RepliesI posted my passat to sell/part out last week. So I talked to the mechanic today and he hasn't looked in the engine. He just says that when the timing chain goes it wrecks the valves and pistons (needs rebuild). HE WAS TRYING TO SAVE ME MONEY THOUGH...FAMILY FRIEND. My sister got lucky on her passat and only messed up the valves. But she was sitting still....I was doing 80mph on 95 going to work. Should I have the engine looked at or sell it.....what are the odds I got lucky??? I found a lot of posts/blogs about how everyones engine blew, but no one said they got lucky.
View 9 RepliesI was thinking about checking out the above vehicle at my local dealer (Chevrolet). They're asking 15.9k and it has 57k miles. I need to know if it has a timing belt or a timing chain and how reliable is the engine/transmission.
View 1 RepliesOK, so yesterday I changed my timing belt and all new components. I started the car before completely reassembling everything (bumpers, etc.) and it ran a little rough at first, then smoothed out. But this only lasted a few seconds and then it died out. I thought not much about it and finished my reassembly. Afterwards, the car would crank and crank and finally start. However, it would never idle smooth and it stalled out only after 1-2 seconds.
I did some investigation, and found the plugs all had wet oil on them. Changed them out and tried to start car with same results. Looked again at the plugs and they weren't as oily, but on their way. I looked all over for a source of this problem and found a broken "pipe" on the passenger side of the engine. It is black and sits behind a heat shield, directly under a larger black pipe. They both run from front to back. I think the broken one might be a vacuum line of some type, although when I plug it, nothing happens.
My fear is that I botched the timing belt job and subsequently, bent a mess of valves. But, I'm holding out hope for another cause of this dilemma. What is the smaller black tube/pipe on the side of the intake? The broken piece comes off a 90 degree elbow pointing to the ground. I'm guessing it was broken before the timing belt job, but who knows? Perhaps I broke it when I moved the radiator into service mode. Could it be part of the turbo? I thought that might cause the rough idle and stalling.
Oh, one other thing. When I last tried to start the car, I got a flashing "STOP" on the instrument panel, followed by something about the oil. The oil words only appeared for a split second before going away. Not even long enough for me to read the whole sentence.
I know this isn't the usual ticking of the injectors and I believe it's to fast to be a lifter tapping. I believe it's the camshaft chain hitting against the valve cover. I took the valve cover off and the chain is still tensioned tightly so it makes me wonder what this could be..
View 1 RepliesI brought my 2004 VW Touareg V6(83k miles) to the dealer for a recall on the ignition call and much to my surprise, was presented with a diagnosis of a $6,000 problem! The dealer told me that the computer read some codes which say that the timing chain is stretched and needs to be replaced. They said it will take 4-5 days and should be done asap so it doesn't "go out", because if it does, it's an even more expensive problem. I took the car to another VW repair shop and they asked me if I heard any noised when I start it cold (like pebbles in a bucket). I have not had any problems like that at all, so they said I shouldn't worry until I start getting symptoms. They also said there is no recommended point (like 90,000 miles) when VW recommends the change, so it really shouldn't be a common problem. I want to do the right thing, but I don't want to rush into an expensive repair if it isn't necessary.
View 1 RepliesMy 2k Passat has 130k on it. I have done regular oil changes and had the timing belt done 6 months ago. It is in Las vegas right now, as it wouldnt start, and I was informed that it needs a new engine. It ended up starting when the guys at the shop squirted tranny fluid down a plug hole...but has been smoking. I was told this means I have a blown head and the engine would have to be torn apart to check out the bottom half.
I am almost inclined to continue paying to store the car until I pay off the 5k that I still owe on it, just to turn around and junk it...but I feel like maybe that would be rash.
I have a 01 Elantra and my daughter has a 02. Both cars have the camshaft sensor at the front (timing belt) end of the engine. My daughters car is a early model with a 01 engine in it. My understanding is that later 02 engines moved the camshaft sensor to the ignition coil end of the cylinder head. My question is did the timing remain the same so that if I put a 01 engine in a late 02 body and spliced the sensor in would it work correctly?
View 8 RepliesI have a 04 jetta bbw model engine with timing belt failure. while trying to replace and get camshaft back in time i cannot find a timing mark on camshaft gear as usual.
View 7 RepliesOn Feb 2015 I had this oil leak developing around the timing chain cover/ oil pressure plug and so i replaced the oil pressure sensor and clean the area and though problem solved...
Fast forward today and the weeping has redeveloped and has gotten larger than last time , its only a weeping issue no visible oil droplet leaks, anyways I took a mirror and when probing around and found the leak origin from the rusty looking timing chain tensioner...that what i think it is.
My question is should I just remove and replace the Rubber O-ring on it or should I just replace the entire timing tensioner unit with a new one, my original timing chain tensioner is sitting at 85k miles. The O-ring is free (i have a kit) and i can do it right now or a New Timing chain tensioner w/ new O-ring is around $20 bucks but i cannot verify the part number ...
I have an '09 Tiguan that recently began to start hard. Two days ago, it refused to start and hasn't started since. It cranks and cranks but to no avail. I disconnected the fuel line at the first hard piece on the front side of the head. The primer pump when activated pours gas out of the line for about 5-8 seconds.
I also pulled the coil packs off and verified there is spark on them. I scanned the car with vcds and came up with nothing other than a couple voltage codes (battery is low at this point from cranking and is bulged and showing yellow in the spot window).
Tonight I borrowed the perfectly fine battery from my B6 and attempted to start it. No codes whatsoever and yet it still refused to run.
I read for a few second at start up ok . Have it checked : [URL] ...
I will be opening up the case in next few days. Chain still on holding by a few teeth. Metal wedge between teeth and chain.
I have a 2006 Honda CRV with 145,000 miles on it. It has been giving me warning lights for about 10 weeks. My mechanic discovered that it is burning oil, which he says all old cars do. But the lights continued. He put the computer on it and says that I need a new timing chain and it will cots $1,100.00. He also says he's not 100% sure that this will stop the lights. I don't want to sink that kind of money into the car if it won't correct the problem. The lights that come on are the check engine light, the VSA light and the triangle light. They do not come on all of the time. Maybe 3 time a week but they go off if I stop the car and re start it.
View 19 RepliesMy neighbor have a neglected 1995 Dodge Ram with the 3.9L V6. This engine is called a "Magnum" but I have to say it is pretty gutless overall. Anyway, it has the famous clatter caused by the timing chain tapping against the timing cover. Every one of these from this time period sounds like this and I understand it is a common problem. Is this a critical problem or not? I understand it can be fixed by replacing it with a newer style timing set with a tensioner. If this won't cause damage, I say leave it alone as the noise is just a minor annoyance. I was just in as far as the water pump and was tempted to tackle it but figured it could wait.
View 10 Repliesmy car timing chain jumps up and down wen i try to start it.befor that i hard alot of clinking sound coming from the motor now the car wont start
View 7 RepliesJust purchased a 2002 Camry for my son to drive to school. The car has 275,000 highway miles on it The car was well maintained by the previous owner. I have heard that the timing chain should last about 300,000 miles. However, the owner's manual does not mention any replacement interval. Since the cars mileage is approaching 300k, I'm wondering if the chain needs to be replaced. The engine runs great. However, I do hear a bit of a rattle from the timing chain pully area. I replaced the valve cover gasket and inspected the chain but didn't notice anything unusual. I have mainly driven import cars with timing belts and not sure if this rattling noise is normal for a Toyota with a chain or an early sign of needing replacement.
View 5 RepliesExperiencing a really bad rattle after changing the oil? It sounds like the chain tensioners are losing pressure during the oil change.
View 11 RepliesI just replaced the timing chain and water pump on my 1999 K1500 5.7L. After spending several evenings and a few early mornings working on it, I get everything back together and go to start it up. It starts then immediately dies. After double checking that the CKP sensor, two plugs on breather, and a/c and alternator wires (these are all that I unplugged) are connected I try in one more time before coming in to work today.
Timing chain was installed with No. 1 at TDC and mark on cam at 12 o'clock position as stated in the Haynes manual for the truck. I did not remove or even touch the distributor since replacing the intake gaskets ~3 years ago. Will check to see if any codes are showing in the morning when I have my laptop at home.
Changing timing chain tensioner? Mine is making the rattling noise on startup. Tried searching one internet for any DIY's out there. Haven't really found any good ones.
View 7 RepliesMy 2007 3.3l SF timing chain cover is leaking.It has 93,000Kms and is still covered by warranty.The Dealer said it was a 17hr break down job to do.
I am wondering if there are things I should get done/replaced when they open the engine up. I had asked at the dealer if there were other parts that should be replaced at this time, but was told that there was not.