I have a 2000 Passat 1.8T 5spd that today started stalling out. I start it up and it idles fine but when I go to give it gas, it stalls out at around 1600 RPM. My guess is that the Fuel pump may be bad, or i have got bad plugs or coils. It was running fine this morning but it just started doing this around an hour ago.
View 7 RepliesI am having trouble with my car hesitating when it sits between 1600 and 2000 rpm. My car does a rapid shake that is felt throughout the car. It lasts for 2 seconds and then disappears. It has been happening for a month now and it seems to be increasing in frequency. My husband doesn't believe it is a major problem and that it can wait.
View 2 Replies2012 Camry SE 4 cyl, 56K miles ... Happens in all gears, in normal and sport mode “under light acceleration” at 1600-2000 rpm.
Sitting in driver’s seat I hear a drone which sounds similar to the engine lugging we hear briefly at around 1000 RPM. In the 1600-2000 RPM range it is very annoying because this is the cruising range on highways. Sometime when going up a slight incline it can be felt through the accelerator.
When seating in back seat on passenger’s side, it sounds similar to a bad muffler/resonator and is very audible. Spring loaded exhaust couplings in front of muffler and between front pipe and converter are not seized. All rubber hangers are there. Installed “B-quiet” sound absorber in trunk going from spare tire well over top of muffler and up rear quarter panel which did not work. Nothing is touching the exhaust under the car.
When idling the exhaust produces a noticeable putt-putt sound. Toyota rep (not dealer) went for a ride with me and feels it is typical of a car “for this mileage” (same as dealer told me). I stated it did not do it before and was told cars wear in and after a while characteristics change.
I have a 00 Passat GLS.
When i accelerate, whether it's hot/cold/wet/dry outside, the car almost stalls. I have not had it stall yet, usually out of pure fear, i drop the pedal to the floor, and i catches up. I have had this happen at very inopportune times, like joining traffic. The car does a sort of stutter step.
I know little about new cars, but i feel like the fuel or air aren't making it through nicely.
I just bought a 2000 VW passat GLS 1.8T, and I'm having a very odd problem with it... I have trouble starting it, almost like the starter is going out, then it starts and runs fine, then I'll be driving and the screen on the gauge cluster will say stop and I'll start getting a beep, if I don't stop the car dies, if I do then it just sort of putters for a second and then goes back to normal, when it dies it loses all power completely everything shuts off then it resets. At first I thought it was the starter, then it started doing this.
View 2 RepliesI have a 2001 Camry LE, 4 cyl, 2.2 liter, automatic transmission, 163Kmiles on it.
I'm hearing what sounds to me rather like a grindy sound at around 1400-1600 RPM. Initially the Camry seemed to do it only after getting into 2nd gear at about 10MPH, but now i see that it is associated with RPM and not the gear so much (the noise is less frequent and less loud in 2nd and 3rd gear- not noticing it ever at above that). I should say that the Camry has been making lots of noises since a new exhaust was put in by a cheap Bosnian shop.
It seems to only make that particular grindy noise when starting from a dead stop, but not if i was already coasting at all. So far as i can tell it seems to only happen about half the time- if I'm accelerating very slowly it doesn't seem to happen much. If i start climbing a hill after a dead stop it seems to come on fairly reliably.
It does not seem to make the noise when passing down through 1600 RPM while slowing down or revving down.
When i started the Camry up today, the noise cropped up well before i got to 8MPH (where it typically shifts into 2nd gear). Which is to say the noise appeared before it even started to shift out of 1st gear.
If i stay in Drive or Reverse and apply the brake so as to not go anywhere, the noise generally starts around 1600RPM. Since the car isn't moving, i think this might rule out the transmission. I hope.
However when in Neutral or Park and i bring the engine up to 1600RPM and beyond, the noise does not appear. So that's perhaps not so good. Of course my car idles a lot better/smoother in N and P than it does in D or R. It's rather rough idling in D and R.
I'm hoping maybe it's a vibration issue- something like harmonic amplification- where something only rattles in a certain frequency range. I pulled up next to a brick wall, kept on the brake, went into D and got up near 1600RPM and the reflected noise does strike me more now as maybe being less a grindy noise and more of a rattly vibration.
The Bosnian shop who fixed up my exhaust were too quick to dismiss the noises i heard after they worked on it. I think maybe something is loose. I hope. (I could feel air leaving the flexpipe's woven area itself but don't know if this is normal.)
Going up hills increases the likelihood of the noise appearing (so i take this to be suggestive that it IS the transmission).
However on a flat road if i hit the gas to quickly get up to 1600RPM before I'm any where near auto shifting out of 1st gear, the noise also usually appears (so i take this to be suggestive that this is not the transmission). I've also gotten the noise to not appear until well into 2nd gear.
The fairly-repeatable noise appearing in the 1600RPM zone regardless of my gear position gives me some hope that the xmission is not the source of the noise. So on balance, i think there's some indication it's the transmission, but there's also evidence that the source is other than the transmission.
The noise does not occur in Neutral or Park while revving up to 1600RPM. But then too, the engine, exhaust and vibrations always seem considerably less in N or P, as opposed to being in Drive (or Reverse). Why my Camry is quieter and more smooth in N and P as opposed to D or R? In the latter two modes, i imagine the transmission is engaged? And that the transmission is unengaged in P and N? And would that make the car louder or vibrate more, at least under certain conditions? Is the engine under less load in P and N?
And are noises at certain RPMs in D or R, but not in P or N indicative of Transmission problems? I notice the shop overfilled the transmission fluid every time i've had it changed.
I have about 80K miles on my 2002 F-250 P/S. My AC will cool big time when I first turn it on. But, after I have been on the road for a while (20-50 miles), the AC turns hot. I noticed that the compressor clutch disengages when the engine goes over 1500-1600 RPM and when the engine slows back down, the clutch re-engages. I have had:
1. Bugs cleaned from the front.
2. Evacuated and recharged (3 times).
3. Cycling switch replaced.
All these were done by an authorized Ford dealer. But the system still gets cantankerous at cruising speed (1900-2000 RPM).
I got a 87 Toyota Celica 1600 GT, with a TVIS 4A-GE engine in.
My problem: when i just start the engine cold, it revs to 2500 RPM, and stays there for 1-2 minuttes and then falling to about 1500 RPM, and when the engine is completely warm my idle is about 1000 RPM.
first i think that 2500 RPM cold is a bit to much, and i dont know what to do with it. but my biggest problem is when the engine is fully warmed up, and i rev it to lets say 3000 RPM and then lets the gas of, the engine falls to about 500 RPM sometimes it stalls but if it not stalls then it would slowly gain some RPM and then it goes up to 1000 RPM again.
How can i prevent the engine falling that much when i let the gas off? it's quite annoying when i drive the car and comes to a stop it sometimes stall.
My 2005 F150 makes a diesel sound when I accelerate. It only does it between 1600 to 1800 RPM and stops. It only does it in overdrive. Its a 5.4 liter with about 95000 miles on it. What this could be? I cant tell if the noise is coming from the tranny or engine.
View 1 RepliesMy 2012 F250 6.2L (Gas) engine developed a noticeable drone/vibration when in drive between 1600 - 1800rpm. RPMs above and below that range is fine. But when accelerating, as soon as the RPMs reach 1600, you can feel a slight vibration through the gas pedal and a noticeable sharp draon/moan up till about 1800 or 1900 rpm, then its normal.
I took it to my ford dealer and took the service manager out for a test drive. He said that there is a drone and slight vibration withing that RPM range. He thought that the engine mounts may be loose. But aside all that, he felt something was off and wrote up the service order.
When to pick up the truck and now the service manager changes his tune and said that the drone is normal and happens on all 6.2L super duties.
To be honest, I have the feeling he is pulling my chain.
I have a 2000 hyundai accent. I shut it off in my driveway earlier and went in long enough to use the bathroom and when i came back the car would not start. I squirted gas in the intake and it fired right up. A little later i was in town and it stalled and would not re-start. I had to walk to the store and get some ether to get it started back up. I have noticed since the first time that it will cut out every now and then for just a second and then go again while running down the road at around sixty mph... im at a loss as the local mechanic's computer wont hook up to it and there is no place to check the fuel pressure as i had wondered if maybe that was the problem having had another car do that before. the check engine light is not on either
View 2 RepliesI have a 2000 Nissan Xterra. About a month ago it stalled while I was backing out of a parking spot. When I turned the key, the engine turned over but wouldn't start. A few minutes later it started and I drove it on a long road trip. It was fine until today when it stalled when my husband was going around a corner. He waited a few minutes then it started. Now tonight he started it, drove down the block and it stalled again. This time it won't restart.
View 1 RepliesAny way, my 2000 Pontiac Sunfire will randomly not accelerate while I am driving. I was initially rolling up to a red light so took my foot of the gas at about 20 mph, then the light turned green so I tried to hit the gas but nothing happened for about 5-7 seconds. So I was just coasting, but then I hit the gas and everything was fine. It did this a second time on the way home. Two days later I went to start my car and it wouldn't start. Nothing was happening--no noises, nothing. So I got my battery tested--Autozone tested it and said it was bad, but after replacing the battery nothing happened still.
Then a "mobile mechanic" came and stuck a screw driver into the starter to short circuit it so it made a sound like it was trying to start, but didn't. Then after a few minutes he looked and my radio was on and it started with the key. Since then it has not started only one time when I used a screw driver to start it myself, but when I was on a steep incline last night it kept not accelerating if I made it work too hard. I would be at ~65 mph and it would just quit so I'd pull off the side of the road and it would drop to ~40 mph for ~5-7 seconds, then I'd hit the gas again and it would go just fine. It did this about 3-4 times. One time all the lights on the dashboard flashed on when it wouldn't go. One time it just completely stalled on me when I was driving. I pulled off the side of the road and started it again and it was fine.
I have an automatic 2000 Accent.. It stalls after a short distance. I changed the wires, spark plugs, and today I changed the fuel filter and put some injector cleaner but no change.. right after the filter change, it seemed to be OK but I drove about 10 minutes on highway and it stalled again.
If I wait about 10 minutes it starts again but not for long.. According to this, what else can it be?
My camry with 87,00 miles stalls when I take my foot off the break at stoplights. Three certified Toyota mechanics say they can't fix it until it happens again. No one is interested in checking for clogged sensors.
View 2 RepliesI have a 2000 honda v7 coupe and recently I've been having problems starting it. Generally when I drive to work in the morning it's fine. However if I am running errands and make many stops then it isn't. After stopping at one place I start my car like usual, then the RPMs rise, the car rumble, and then it stops. However if i pump the gas then it is fine. When I am driving then I have no issues and the car runs smoothly. I recently had a major maintenance and also told them about this problem. They said that they couldn't diagnose it since I didn't bring it in with the problem.
View 1 RepliesI have a 2000 Mazda 626, V6, 5-speed with 157,000 miles. The car cuts out (as if it's loosing fuel) and stalls intermittently. This has been happening for 3-4 weeks and neither my regular mechanic nor the Mazda dealer can figure out what's wrong. Here's what they've tried: new fuel pump (replaced 3 times to make sure parts not faulty), new wires and plugs, new alternator belt, replaced fuel pressure regulator, replaced mass air sensor, cleaned/checked fuel & air filters, replaced coil/distributor (2 times to make sure part not faulty), checked for vacuum leaks, checked ignition/sensors (CAM and others).
It has been stalling intermittently for 3-4 weeks, though for a while would not do it when with the mechanic. Also, the check engine light would never come on, so there were no codes to check into. Sometimes after it would stall, it would not start up again until the engine was cold. Recently, it stalled when the mechanic was test driving it. He pulled off the mass air sensor and it started right up. He replaced that part and the car was driving OK for several days. I even took it on a couple 2.5 hour round trips. Today, however, I could not get it started. It would turn over, but not fire and it seems to me that it wasn't getting enough fuel.
I own a 2000 nissan altima GXE, and recently i have had a lot of problems, it would stall out randomly and OBD2 scanners said knock senor, EGR, and thermostat. I changed the knock sensor, cleaned the EGR valve and the EGR valve gasket, and haven't touched the thermostat. I changed other things like the crankshaft sensor, fuel filter, fuel pump is fine, alternator, valve cover gasket, and spark plugs. It started stalling all the time after I changed the rotor in the distributor cap, it stalled before but less than after we changed the rotor.
The car would stall randomly when the RPMs would go below 1000. I took it to my friends dad who is a mechanic and he was the one who changed the PCV valve and the EGR valve gasket and cleaned the EGR, he also cleaned the intake and changed the knock sensor. The SES light finally went away but the car would stutter when i would be stopped with the A/C on and i go to press on the gas. once the RPM hit 1000 it would stutter. It didn't stall until a week and a half later. I was told it could MAYBE be throttle position sensor, computer, thermostat, oil loss from valve cover gasket, and idle speed control.
2000 sunfire SE 2.2 L engine. Firstly, I should mention the present temperature out here is -37 C.
So here is the issue I am experiencing. The car does not idle smoothly. In fact I find it idles a lot lower then my fiances 2005 sunfire (hers idles at about 1000 RPM). My car idles around 750 RPM. and I've noticed for last couple months when just idling its not very smooth. The RPM will idle at 750 and then drop down a bit and back up again. It never has been a big problem till now.
While driving it yesterday, whenever I would let go of the accelerator the RPM would drop right down to 500RPM, and you would hear as the heater (air blowing) would completely drop down, and lights would dim significantly, and then within a split second, RPM would jump back up to 750 and blower and lights would return to normal. It almost feels as if the RPM is too low for Alternator?? That it's not able to produce enough power for electrical devices. As well, while braking if the ABS kicks in again I see this drop in RPM along with lights dim and blower airflow drop. Once again only for a split second though.
Here is the big problem. the drop in RPM and amount of disruption it causes actually had my car stall when I let go of gas and hit brake and had ABS kick in.
I am not sure if this is a problem with having the idle set too low, spark plug problem or something do with alternator?
I have a 2000 Ford Focus Wagon with 114,00o miles on it. I'm having a problem determining why it is stalling in reverse and also sometimes while it is idling. I've had the idle speed motor replaced, hoses checked, etc. After we had these things done the car seemed a little better but I could still feel the car hinting at wanting to stall.
I also noticed it usually stalls in reverse when I'm turning the steering wheel but not if I'm backing up in a straight line. It also feels like it wants to stall when it sits at a long traffic light. Before I had the idle speed motor replaced it stalled more often - several times a week. However, now it stalls a little less.
On another note, the car seems to idle a little rough. It almost sounds like a diesel engine. It seems to simmer down some once the engine is warm. I had a new water pump installed and a timing belt put in and now I can hear a squeaking sound coming from that area of the engine. I'm not sure if any of these symptoms are related.
My girlfriend has a 2000 Alero 4 door. This car is basically our only mode of transport. I'm disabled and I'm trying to keep the car running as best I can. Just recently the car would stutter at complete stops. Then it went to stalls. This doesn't happen when it's cold only when it's warm and within operating temps.
I replaced the TPS but the stuttering and stalling is still happening. I'm ready to go through the car to find the problem... but I don't know where to go from here. I've cleared the computer to clear any dash lights and hoping it would reset the TPS. This didn't work.