Passat (B5) :: 1999 - Dipstick Funnel Broken
Sep 20, 2005
I bought a 1999 Passat 1.8T a few days ago. I noticed before I bought it that the dipstick funnel was broke but I knew it was only a $2 part. Today I bought the part at a local dealer and went home to install it. Problem is the old one is actually broke in half. One half remains on the dipstick the other half on the tube. I can't for the life of me get that thing off the tube. I have a inspection scheduled at the dealer tomorrow so if I can't get it off I will probably just have them do it.
View 1 Replies
Advertisement
I was checking the oil this morning before getting ready to drive (for an hour) to the in-laws for Christmas, and the Effing orange plastic dipstick tube broke about halfway down. Now I'm afraid to drive for an hour at highway speeds, for fear that a lot of oil might come out of that compromised Effing orange plastic dipstick tube part -- would you all agree that I should not drive the car? Figures this would happen on Christmas Eve when nothing is open.
Effing orange plastic dipstick tube!
View 6 Replies
I have a broken dipstick sleeve for my 2003 Passat 1.8-liter.
I bought a new sleeve from the dealership, but not sure how to uninstall the old one and put in the new one.The oil sleeve is in a tight spot. I can't understand how to remove it without taking apart other engine parts.
View 4 Replies
I just finished putting a 7.3 back in one of our f450 plow trucks today, so then i moved onto our 2001 F250 5.4 plow truck. The dipstick tube was rusted in half so i pulled on the remaining half to get it out and put in the new dipstick. However, it broke off at the block. So now i cannot see how to get the rest out with out doing a lot more work. I haven't removed the splash guard yet but will i have to remove the manifold , the oil filter base, or both?
View 14 Replies
I want to have my oil cap sit close to the valve cover rather then have that long funnel.
I want to go from this:
To this:
View 7 Replies
I went to check the oil today. For the second time the end of the dip stick is broken off.
View 24 Replies
When having an oil change at Valvoline, the mechanic informed me that the tip of the transmission dip stick was broken off. If this tip is floating around could this piece of metal damage my transmission?
View 4 Replies
I have recently inherited a 2000 Jetta. The car runs great however the plastic tube that holds the oil dipstick is broken in two or thee spots. It has been previously repaired with electrical/duct tape. Doesn't seem to leak but I'm wondering if I need to get a new one in there. Is this something I can do at home or does it need to go to a shop?
View 3 Replies
It's really not relevant what brought up this question but do you think a broken dipstick tube can cause an engine to run lean and why do you answer that way?
View 3 Replies
I went to check my oil this morning even thought its only been roughly 2000 miles since the last change/filter(Napa Gold and Mobil One 0w40). I noticed that the dipstick had just a tad of yellowish snot stuff on it. I know it mean water in the oil but I cleaned it off and recheck, put a hair more in and it was all clean no more snotty yellow gunk.
My question is because it is cold and my dad moves it almost every morning before work could it be condensation? I know with my 1998 Chevrolet Tahoe with roughly 153,000 miles used to get the same yellow snot stuff in the oil fill neck but never on the dipstick. The passats oil filler cap/neck were both free of any snotty stuff.
If its still like this tomorrow I'm taking it to the dealer. Also there's still coolant and I couldn't be sure if there was any less as if it was a leaky head gasket but the rest of the oil is clean and not milkshake like.
View 5 Replies
Just finished changing my oil and noticed that the dipstick was cracked. Upon further inspection I noticed the end which mates with the plastic tube was cracked and there were missing chips. I can only imagine where they ended up, in the oil. My question is, what to do? Since this is a plastic component, I assume that it will not harm the interior engine parts, but not 100% sure.
View 5 Replies
am i supose to read it when the car is warm or when the car is cold? cause when it is cold it says i dont have enough oil but when the car is warm it says i am a little above
View 7 Replies
I have the above passat with the AWM motor. There is signs of moisture in the dipstick tube, but not on the oil fill cap. Now today the plastic dipstick funnel snapped due to being frozen to the dipstick.
Now the dipstick had what looks like lithium grease on it. The car has been slowely loosing coolant. But exhaust is clear, no signs of steam or coolant burning through exhaust.
But if the lithium grease like substance on the dipstick was a oil/coolant mix WHY did it freeze . I use a 50/50 mix of pentofrost SF. According to their lable should be good down to below zero. It has not gotten that cold here yet, even at night.
Why or how I could be getting moisture into the motor? And why is it only visible on/in the dipstick funnel and nowhere else.
View 6 Replies
I was checking the oil this morning before getting ready to drive (for an hour) to the in-laws for Christmas, and the Effing orange plastic dipstick tube broke about halfway down. Now I'm afraid to drive for an hour at highway speeds, for fear that a lot of oil might come out of that compromised Effing orange plastic dipstick tube part -- would you all agree that I should not drive the car? Figures this would happen on Christmas Eve when nothing is open.
View 6 Replies
Car is burning through a higher than usual amount of oil? I just went to the dealer to do an oil change because the oil was so low I could barely get a reading on the dipstick, no leaks were found, and the car does not smoke.
View 6 Replies
We just past 1000 miles on our new 08 2.0T wagon and there is '0' oil consumption. The dipstick reads completely full. And...it is noticeably cleaner than our 06 2.0T after 1000 miles (after oil changes).
View 6 Replies
Pulled my dipstick out to repair the flange seal where the tube goes into the pan. Now it sticks out about 2 inches. Ive tried putting it in both ways. Now it was sitting in my truck over the front seats with the center armrest down, so it may have gotten bent the wrong way? I read a few tricks online Ill try after lunch here. I did have some vice grips on the tube to try to get it off of the flange, but I took my fingers and felt the entirety of the tube and didnt feel and dents or irregular bends. Right now the tube is held by zipties, as I had to cut the bracket off, its a long story. . . So is that something that would make it stop short? Does this truck have a 2nd tube that sticks into the oil pan or is it just the one?
View 13 Replies
Heading back up to get the last load of antique tractors from the show and something seemed funny. 2 miles later turn into a side Road less power. Pull over. Oil everywhere. Shut it down. Nut completely unthreaded.
Get it on and tighten as best I could with a pair of channel locks one size too small. Dump in a gallon of oil. Now it is just on the stick. Start it and sounds good. Still leaking.
Called a buddy to see if he can get me. Yep sure but his wife is not happy. Something about him going to Texas at 7 am for work for a week..... Give him directions hoping he makes it since he has no sense of direction.
Obs 7.3 stops. Talk to him. He doesn't have anything better for tools on him but lives a mile down the road. Drop the trailer on the side of the road. Drive to his farm and got some better fitting pliers. Either I got too heavy handed or I cross threaded it. Stripped the nut. The flange threads look good.
Drive back to the trailer and sit intersection so my buddy doesn't miss it. Hook my trailer to his truck and get mine loaded. In the end it turned out as best as it probably could have. Pictures to follow when the sun comes up. Time to read up on the dipstick flange. Hoping a new nut and o-rings will fix it.
View 14 Replies
Just did a drop an refill of my trans fluid. Put in a little under 8 qts.
My question is where should the fluid read ? Is half way between full and E good or should it be right up to the line ?
Obviously I'm reading it while trans is warm and in nuetral, engine running
View 2 Replies
The dipstick tube on my 5.4 snap and ive ordered a new one. it looks like it may not be to hard to replace.
View 4 Replies
04 f250, 5.4 ,90,000mi. Checked my oil today and saw this white flaky crap on the dipstick its salt, probably from a broken dipstick tube, probably broken at the manifold right where there was a huge deposit salt right on top. The manifold is leaking anyway I was hoping to wait till spring when everything dries out and warms up a little bit, but with salt getting into the engine I think I have to do it now. Is there any way to deflect moisture off the road away from the exhaust manifolds?
View 4 Replies
