My daughters passat will not shift gears. Does'nt shift up when taking off. Does'nt slip or make noise. I have a 87 and 88 Cabriolet, one auto, the other manual 5 speed. Both have problems but, with the search key I have located and made repairs.
View 1 Replies2 wheel drive. No problems shifting until a few weeks ago when I put a chip in the truck. Then became a funny sort of half shift in between 1st and 2nd. Kind of a half shift and then a final hard shift into the next gear.
I have only driven the truck with the chip setting in economy by Gearhead which is 40hp. Well, all day driving in an economy but I have played hard with all the settings, smoking my tires and what not but never actually driven it into anything other than the economy.
Tonight it's done. Starting in the normal drive from a red light it was in between that funny shift and then it just fell back all the way with a hard thunk followed by it wouldn't shift at all out of first gear. Took it out of tunes, same difference. Found out when I take off in drive it won't shift on its own out of first but when I put it in second from the tree it shifts into second as normal, coming from the drive. Then when I start getting up into the rpm range that she normally should shift past second I put her back in drive and she shifts into third (and fourth?) normally. If I remove the overdrive it still immediately downshifts. When I turn it back on it shifts back up normally.
But again, starting from drive I have to put it into second and then into drive for it to shift. I still have reverse and it still kicks directly into first from the park and takes off, just doesn't shift from first to second on it's own.
I checked the tranny fluid, it's seemingly fine. Great red color and full. Does not smell burnt at all. No flashing light or anything anywhere either. No blinking on the overdrive light on the stick or no warning lights anywhere else.
This is what’s wrong with my 1998 Honda CR-V manual transmission. When it’s off, the gear stick works normally. However, when I start the car, the gear stick gets stuck and won’t move to change gears. It happened before a couple times and if I warmed the car up for about 10 minutes it worked normally again, and normally the next time I drove it. However, this morning, the gear shift would not work even after warming it up, except when the car was turned off.
View 5 RepliesI have a 1997 chevy s10. Speedometer stopped working..abs lights come on once in awhile and wont shift into other gears. I have replace speed sensor, computer, wheel sensor and ignition switch assembly.
View 7 RepliesI have a 98 passat v6. I was changing some fuses today and i restarted the car after that and i noticed the gear selector is solid so i looked in manual and it says car has electrical malfunction, how to get the car out of this mode i have had no problems until I touched the fuses ...
View 3 RepliesAfter driving around hard for a couple minutes I got home and the car smelled like something is burnt then I went out to drive normally to get the smell out but didn't work. Then I realized my gears were hard to move into especially 1st, 2nd, 3rd. Its hard to change into those gears now. what could be the reason? What do i need to do for my gears to move smoothly again? I just got this car, my first.
View 5 RepliesA few days ago when it was real cold my car would not shift into any gears. I shut it off and started it in neutral and was able to get it to shift, but after leaving it for a day or two it now will not go into gear. I have tried starting it in neutral and park, but it still will not let me push in the little thing to allow me to shift into reverse or drive. Why this might be happening or had this happen to them?? I'm thinking it might be related to the really cold weather. It's a 97 passat...Automatic....
View 1 Replies1997 2.3 5 Speed. My poor truck is having a hard time shifting into gears. I have bled the master off the truck with the correct method, bled it on the truck with the hose on the slave method while pushing the pedal and multiple times with no bubbles coming out at all, no leaks, etc.
Here's the breakdown -
- Clutch, slave cylinder and shifter bushings replaced about 3 years ago (everything has less than 7000 miles on it)
- While driving and pushing in the clutch, it clearly disengages, although quite a ways down.
- Only shifts hard while running. If I sit with it off with the clutch in, I can shift through all the gears with no effort whatsoever. At times while driving, it gets so hard to shift that it may become dangerous.
- Only things I haven't replaced are the master cylinder and the flywheel.
Should I just assume a bad master and just replace it? It's the original with 188,200 miles on it.
Forgot to mention there are times that when I am at a standstill trying to go into reverse, it grinds like the transmission is still engaged.
I've just bought a 2002 Passat, v6 5 speed manual with 119,000 km on it. When I shift through the first two gears the rpm are not dropping immediately... about a 1 second lag. I haven't had a clear answer about what it is I have called two dealerships and two independent mechanics except. They say that it could be a variety of things that might be wrong with the throttle body.
View 6 RepliesHow to fix a gear shift that tends to get stuck once in awhile. What about WD, and how would you apply it? I have a '97 Monte Carlo.
View 2 RepliesI have a '97 F150 Lariat Ext cab, 5.4, 2Wd, 175K, a bit rusty but for the most part functional. Unit is parked for long periods of time.
3 - 4 years back the gear shift did not want to go into PARK and and the gear indicator was out of register. Unit would not start and I had to move shift lever to N to start. Fixed the two screws on shift plate/column per this site. Then 18 months ago same thing begin to occur but this time I used blue thread lock to hold screws in place. Still had to throw into park to get it to stay.
6 months ago shifter became very difficult to move and near impossible to get into PARK. When in PARK the interlock must have not been engaged so had to move to N or push lever hard into PARK to start.
Tired of this so I cruised the site and found several posts on taking dash apart, repairing a broken shift tube and or replacing bushings.
Battery disconnected, dash apart, cluster out, steering wheel still on and steering column still in position. Shift tube appears OK, i.e. not broken as in one post, bushings appears OK as there is no play or slop evident, but I cannot get the shift lever to move from PARK, period.
When the shift lever is pulled toward the wheel, a pawl on the tube causes a plastic or nylon arm to move about 90 degrees. It must be a stop or safety of some sort. I have not dug deep enough to see the shift plate with the two screws. At 75 I find it difficult to lay upside down to reach and hope I can get to them from the top.
Questions:
1. How do I get it out of PARK to check all things on shift tube and gear selector units?
2. Does the battery need to be connected for the interlocks to function?
3. Do I need to drop the column to check on shift tube items?
4. With a rusty trans, can the shift cable to trans connection be the problem?
5. What to look for, how to repair. etc.
having problem w/ 98 f-150. first truck stuck in park. figured out how to get around that (turn key 1 position, shift to neutral, start vehicle, then engage transmission). but no brake lights! I have turn signals, driving lights, hazards, etc in rear. I disconnected harness from brake light switch. there are 2 leads, 1 hot, 1 not. i jumped them and no brake lights. i tested the switch and it functions properly (it's reconnected now). i changed my bulbs in tail lights. I unplugged the solenoid (which is impossibly located behind/beside steering column). this allowed me to shift like an old truck (without having to brake first), but doesn't solve my lack of brake lights (i've reattached the solenoid harness to remind me of my problems).
i am putting my money on a broken wire somewhere between the brake light switch (b/c that was good) and the solenoid (i am not hearing that faint click when i step on brake). but a broken wire should work by accident some of the time (unless cut cleanly and completely). there is a green wire with red stripe leaving the brake light switch and 3 wires at the solenoid harness (1 green and maybe a smaller gauge than those at the switch and 2 others which i don't recall their colors). Ford service manager doesn't think it's the solenoid but wasn't otherwise useful except to say, "hey, why don't you bring it in to me." What to look for before i plunk down for someone to perform what I already have before completing the job!
can i splice a wire from something (? brake light switch?) to something (?wire in solenoid harness?) or does that "electronic signal" get processed somewhere else first?
This is a car i am working on. 01 4motion passat. automatic. Tree fell on it. We put a new roof, quarter, door seats. Last night we moved it outside to clean the shop and went to move it back in. Won't shift out of park. Next tried turning ignition on the backing it off a little and cant get to neutral. Check fuses.
Brake light switch has been previously replaced by someone. and it works. Light next to gear selector working. brake lights fine. I have taken the center console out as much as I can. I can't get it completely out. But everything in there seems ok. When I press the brake in I don't hear any click or anything near the selector.
The other day i was parking the car at my work place. The parking spot was on a hill maybe 10-15 degrees. As I was reversing parking onto the hill the car suddenly stopped and went and stopped and went(about a foot in between). like a manual when you don't give enough gas as you let go of the clutch. When i couldn't reverse in because it kept stopping, i drove forward and it happened again. i ended up letting the car roll forward down a bit and parked in a flat spot. I have always parked at this spot with no problems and i always use my hand brake. Was it because i wasn't giving it enough gas? Should i be worried? It never happened before in the 10k i drove it.
View 10 RepliesI have an 08 R32 and when i come off the the highway ramp and go down a gear the car seems dead or just stuck in between gears when I get back on the gas. I have no power for 2-3 seconds. That hiccup that every one is talking about, when I am in traffic in 1st gear the car just wants to surge off and on??? Is that the hiccup?
View 16 RepliesGears won't shift from park. What's wrong? Is it the neutral safety switch?
View 5 RepliesWe are having issues shifting the car it is hard to shift into gears. I have replaced the transmission and the clutch, trans mount is still good all mounts for that matter are still in great condition its getting tiring to have to slam the car into gear all the time.
View 1 RepliesSo my 2010 Camry LE with manual transmission has developed what I figure will be an expensive problem. It oftentimes grinds when I shift from 1-2. If I pause between the two it's fine, but if i just go straight to 2nd it grinds about 75% of the time so that I have to go back to neutral, let out the clutch, reengage and THEN go into 2nd gear. What could cause this? I'm stumped. There's no issues with any other gears and it does the same thing if I got from 3-2 also. It's to the point where I try to just skip using that gear. It's got about 135k miles.
View 7 Replies2009 Kia Sorento. The Transmission was replaced twice last week and the week before. For the same problem. 50K miles. Auto Transmission...
I have a hard shift between 3rd & 4th gears, I have had the transmission replaced twice. Could it be something else?
I gotta 93 f150 XL it has a 4.9L and a T18 borg Werner trans. I replaced the clutch,throw out bearing, pressure plate and pilot bearing and after reinstalling trans I am unable to go through my gears.
If truck is off I can shift into some gears sometimes but not without a lot of resistance. Also some gears will let me in easy, then fight me as I try to back into neutral.
Truck starts right up but if I start in neutral I can't shift into any gears and get a lot of grinding when I try to put it in gear.
If I start in gear it drives in the gear but I have to force back into neutral. And then I'm stuck in neutral again.
It is a hydraulic clutch and fluid is full and there are no visible leaks. I am 100% sure clutch disc is facing correct way as I triple checked it while installing.
Huge problem. Everything was fine the first couple of times I drove today.
Tonight, when I was getting in the car, it turned on. I tried to change it from Park, but it just stuck and wouldn't move and let me change at all, even down to reverse. It's just stuck in park.
What is wrong with it? What's stuck, and what can I do to get it unstuck? Or else, I'd have to get it towed because it won't budge from park