My 95 Nissan Maxima just failed smog because the MIL light would not come on Everything else passed. The light was working. I last noticed about 2 weeks ago after I had the car washed. I'm reading it can be a bulb or the computer? What can I expect in repair costs?
View 14 RepliesThe switch for CC works fine and will turn green and say 'on' when switched on, but it will not actually work (will decrease speed as soon as you let off gas, just as if it were not on). We replaced the whole gauge panel with one that had CC in working condition (exact same model) and this did not solve the problem.
View 3 RepliesI have a 1995 Nissan Maxima that dies after sitting and idling for around ten minutes. It also has been dying at stoplights, etc. It runs fine if I get the rpms above 1000. When it dies it restarts but often I have to push the pedal to the floor for a few seconds, then it seems to catch and run as long at the rpms are up. I have taken it to a place and due to it's age they couldn't do a diagnostic check on it. I've had the exhaust system replaced (it needed it), the spark plugs replaced, the coolant temperature sensor replaced but still no luck.
View 2 RepliesI have a 1995 Nissan Maxima. The starter will not engage (no noise at all) when the outside temperature is below 60 degrees. All of the electrical is functional, but when I turn on the starter, there is no click sound or any indication that the starter attempted to engage. The car is a manual transmission, so I push start the car, and there is no squeal when the car starts so the starter gear was not touching the flywheel. Above 60 degrees, everything works normally. I have replaced the starter motor and solenoid, replaced the battery, but the problem persists.
View 5 RepliesMy truck is a 91 sierra 2500 over 8600 gvw (8 lug) 5.7 4l80E. After my truck failed a Calif smog test I set about testing the different sensors that are attributed to the reason it failed (a few points high on HC's). All the smog equipment and sensors tested ok except for the 02.
I tested the one in the truck when it failed smog, it came out at 400 millivolts key on engine off as my Haynes manual and the Autozone website said it should, after running the truck for 10 minutes and running it at around 1200 RPM's for 2 min to get the O2 cycling it doesn't, best I have gotten was a slow rise of about 0.01 millivolt rise per second to about 0.590 MV where it seemed to level off, the problem is 2 seperate new sensors do the exact same thing, none cycle rapidly between 100-900 MV as the Haynes manual and the Autozone website say they should.
The 02 is pre-cat stock location, no changes to the exhaust since my last smog check. I don't even know if this is the reason I failed smog, it's just the only thing that didn't pass my testing. the truck does seem to be running a bit rich (per my ultra sensitive tailpipe sniff test).
I did do all the normal repairs after I failed the smog test, tune up, air filter, clean the TB run a can of cleaner through the gas tank, ETC, then I failed the re-test by 3 points worse. The truck does not run bad or blow a bunch of smoke, the truck is not throwing any codes.
I drive a 1990 240 with close to 300,000 miles on it. Haven’t had any troubles with it in the 1-2 years I’ve had it.
Recently went in to get my smog checked and failed two of the three tests: the functional and emissions. I've attached the VIR.
Mechanic said there might be a leak, so a buddy of mine checked the engine for a vacuum leak but couldn’t find anything.
What are the common sources for a failed smog check? I plan on getting a diagnostic later in the week/
smogcheckVIR.png ( 1.93MB )
i have a 2008 maxima with 30000+ miles. its service engine soon light came on recently. i disconnected the battery the light would go off, but would come back on again after a few days. it happened several times now. once i got a code P0011 from autozone while the light was on. the last time the light was on was a week ago and this time the light finally went off by itself yesterday. i took my car to a dealer today. a service advisor told me the reading on his code-reader is NO CODE and the car is fine!. so what have happened and what is wrong with it? could it be serious?
View 4 Replies1990 Maxima. Last night the car started shaking after pulling up to stop sign, it kept shaking the whole way home. Acceleration was slow and difficult. Car started up fine this morning, started to shake again at first stop sign...then it was OK for rest of the day.
View 2 RepliesI just purchased a 2000 Nissan Maxima GXE with 219,000 miles. I've had it less than two weeks, and the Service Engine Soon light just came on. I live somewhere that requires emissions testing in order to register the vehicle. My temporary plate will expire soon, so I need to get the car to pass emissions.
This is my first Japanese car and first non-American vehicle. I didn't know until after I had given the check to the guy selling the car that he used premium gas. He said that Nissan recommends it. I've never driven a car that required premium gas before and wasn't keen on the idea since here, it is 40¢ a gallon more expensive than regular unleaded.
I spoke with my landlord about it, as he is a certified Honda mechanic. He told me to first try getting half a tank of regular unleaded and putting it in with some fuel injector cleaner. He said if I didn't notice any decrease in performance or knocks, to then just add a bottle of of fuel injector cleaner to every other tank of gas.
I got a half tank of regular unleaded with a bottle of fuel injector cleaner and didn't have any issues. I then filled the tank with regular without any fuel injector cleaner. I used about ¾ of that tank when the service engine soon light came on. I took the car to Valvoline to get the codes read, and while they couldn't give me any code numbers, they said it was something to do with emissions.
Here are my questions:
Is it possible the light came on because I switched from premium to regular unleaded or perhaps because I would need to add fuel injector cleaner to every tank of gas I get and not every other tank as my landlord said he does with his car?
Should I try either adding fuel injector cleaner to every tank of gas or just switch back to premium? If I try either of those, and one of those was the problem, how long would it take for the Service Engine Soon light to turn off?
Fix one thing, something else goes wrong. I replaced the resistor or HVAC power module(nissan's term) on my maxima and fixed the problem. Easy job. Put everything back together and now the air bag light blinks constantly when car is running. I did disconnect an electrical connection for easier access to the resistor and plugged back in. I've read, I just need to reset. None of the reset procedures I find on line seem to work.
View 2 RepliesMy ABS light stayed on after driving home in slippery conditions last night. I also noticed a burning smell when I parked in the garage.
View 2 RepliesI recently bought a 2003 nissan maxima 134k and i bought it with the p0300 check engine light on a looked at the engine and though it was an air box problem because they had previously installed a K&n filter so I went to the junk yard and got a 2000 nissan maxima air box and new filter i changed the oil and checked the spark plugs they look new and the dates on the coils are 2012 and 2013 and still its misfiring. i bought it to a mechanic and he discovered a vacuum tank had previously broke and they glued back together so i replace that with a factory one today same problem still misfiring but it got better but now its a p0306 then i erased the code and p0304 came back i erased it then p0302 came back then i change the cam sensors, and the crankshaft sensor and now it get a p0300.
Symptoms:
*when sitting for a long time HARD TO START ( takes multiple cranks to start it ) but once i leave it off for short time like 30 min it starts right up no problem
* when stop at a stop light in drive i can feel small little explosions sounds like my car is beat boxing
*performance is strong good acceleration no problem on that i just don't want it misfiring
I keep failing my emissions because my check engine light keeps coming on. I was told that the problem was the catalytic converter rear and needed to buy one for both sides. The problem I am having that I don;t know which Catalytic Converter I should buy. I know without it is causing my car to stutter. Which I should get?
View 8 RepliesI have a 1998 Maxima with 57K miles on it. I just bought it about a month ago. Anyway, a week ago I noticed It felt very "choppy" when I shifted into Drive or Reverse. It felt like it was going to stall but it never did. The Service Engine Soon light has been on for about 3 weeks but now, when I go up hills especially, that light blinks. I can still drive it but I shift into Neutral at stoplights to avoid hearing the rough idle while in Drive. Went to Pep Boys yesterday - they had the car for about an hour and then informed me that they would need to keep the car for a full day because of the "complex issues involved" - especially concerning the codes. The codes they read were:
p0300 random misfire
p0325 knock sensor
p0440 evap emission
My car passed smog test abut 3 months ago. I can drive it OK it just is very choppy and so there's not a lot of power, especially going up hills.
1998 Nissan Maxima had a check engine light come on and started running very rough. I took it to get a code read and came up with P0320 and P0325. I'm not worried about the 0325 since that's a knock sensor. 0320 is a misfire on cylinder 2.
With the car idling, I pulled the power connector from coil pack 2 to see if it made a difference in the idle - nope. I did the same for the other cylinders, and each responded with a noticeable change in the idle, which was remedied when it was reconnected.
I moved the coil pack from #2 to #4 (swapping them) and the same problem existed - idle was rough and didn't make a difference when I pulled the power on 2, but it did on all other coil packs. So, it seems the coil pack ins't the problem since multiple packs don't seem to make 2 work, but they work on other 4 and 6.
I then pulled the spark plug from cylinder 2, it was very black and looked in bad shape. I replaced it. Still no love.
I then put a spare plug in the coil and was able to see spark as the engine ran, so it seems that the coil pack at 2 is getting juice.
So, I have gas (big odor when the car is running - seems super rich) I have spark. Still running very rough and the 0320 code remains.
2000 Maxima - I just changed the head gaskets, got it back together and no start, no spark, solid security light and linking error to ecu. 50 miles to a nissan dealer. I have 12v to the injectors but no ground, I just checked spark last night and have none. I tried all three keys, will no battery for a month or two cause key security issues? I hate to drag it to Nissan and have them tell me I need a new ecu for a few thousand dollars. Does a security issue cause a linking issue?
View 13 RepliesThe Malfunction Indicator Light on my 03 VW Passat 1.8T just came on last night. After doing some research online I noticed that there seems to be some issues with the coil packs on the 1.8's. Any other issues that this light is linked to?? And is the coil packs still very hard to get?
View 1 RepliesI've just bought a 2005 Santa Fe CRDI 2.0 Second hand, one owner from new, 60,000miles in 7 years. Just had it's 60,000 mile service. Until today perfect. Started car and no revs. but when I put in gear and moved the car, the revs kicked in and I was able to drive normally. Pulled over to side, into neutral, no revs FOR 1 2 or 3 SECONDS, then revved as normal, put in gear, and able to drive OK. Meanwhile, the MIL light came on and stayed on. I know what the hand book says but before I take it to our Hyundai dealer.
View 5 RepliesCar is running fine.. I cant tell any changes in the car at all. Going to the dealer to get fixed and also make them fix my darn headliner that has supposedly been on backorder for 3 months now.
View 2 RepliesMonth ago the malfunction indicator turned on. On checking it was found that wires over the engine were eaten by rats. Reconnection of wires solved the problem.
Today the malfunction indicator light is blinking. Could it be the same wires going loose?
I have a 2006 manual Hyundai accent with 82,000 kms. In the last couple of days the mil has illuminated so i took it to a mechanic who put it on the computer which he says it could be sucking air or bad fuel or many other things. He did cancel the light which stayed out for about 70 kms and its back on its not flashing just illuminated. Can this do any damage to the motor if still driving.
View 11 Replies