Nissan - Frontier :: 2005 - Manual Transmission Shift Shudder After Towing
Mar 19, 2012
I have a 2005 Nissan Frontier with a manual transmission (~6500 pound towing capacity). I rented a large wood chipper this weekend. On the ride home from the rental pickup, the transmission started shuddering when shifting. It is most noticeable when shifting into first gear from a standstill, and less noticeable on each successive shift. Once the gear is fully engaged, there is no shudder - it is only when letting out the clutch that there is the shudder. The truck only has 50k miles on it.
View 14 Replies
Advertisement
My wife and I recently moved to Panama and we bought a 4 wheel drive 2007 Nissan Frontera diesel pick-up. Great little truck so far, 27 miles per/gal! However, the 5 speed manual transmission has started making a loud whine or growl under power. Down hill, gas pedal up, no noise. Clutch in, no noise. Gas pedal down, growling .Growl is related to ground speed as it stays the same when I shift gears.
View 3 Replies
I have a 2005 Nissan Frontier that recently had a new transmission and radiator installed due to a defect where coolant leaks into the transmission and destroys Nissan transmissions. After I got my truck back it ran fine for about 2 days, then on the third day I started it and the gauges all started going up and down at a speed of about 72 bpm. I shut it off let sit for a few minutes started it and it did this again. I repeated that about 4 times. I let it sit for about 4 hours started it and it was fine for a very short drive (1/2 mile). After about another 2 hours of sitting I tried to start and the battery was dead, my friend jumped it and it drove fine. So it sat for a few days until I had my brother jump it so I could drive to get a new battery. Once it was jumped the moving of the gauges started again.
As I was driving, the gauges kept coming on the going off. I got it to advanced auto and they replaced the battery, it started up drove it for a matter of minutes, then the gauges died and it wouldn’t drive faster than 1 MPH, then engine would rev when I hit the gas. I got it to a parking lot shut it off tried starting it the gauges would come on but as soon as I hit the gas pedal it would rev up but instantly the gauges would shut off and the engine would rev anymore. So I was stuck, got it towed to where the transmission was put in. They couldn't fix it but had to jump it to start it, so the new battery was dead. They towed it to a Nissan dealer and the mechanics are now saying it’s just a bad battery, but this just doesn't make any sense to me.
View 4 Replies
I have a 2004 Nissan Frontier with V6 non-supercharged engine, 4x4, with manual transmission, 150k miles. For approximately the last 30k miles, I have had a persistent shuddering in the cab when I apply the brakes slowing from about 15 to 0 MPH. It is accompanied by a low humming noise that decreases in pitch as the truck slows down. It only happens when the brakes are warm; about 70+ degrees outside or after I've been slowing down a lot. It does not seem to correspond to engine temperature, only my perceived temperature of the brakes. There is no pedal feedback, and it does not shudder when I stop using only the parking brake. It does not seem to affect stopping distance.
I first tried to fix it by doing a very thorough front/rear brake job - new pads/shoes, new rotors/drums, and repacked front wheel bearings. That had no effect on the problem. I tried rotating the tires and that had no effect. I then did a complete front end job and replaced all the bushings and balljoints via brand new pre-assembled control arm assemblies. I also replaced the tie rod assemblies, sway bar bushings/end links, and had an alignment done. That had no effect.
Based on the repairs I've done, I would assume that it is having to do with the front brakes, but is not warped rotors or anything in the front suspension.
View 9 Replies
My 2005 Nissan frontier reeks badly.
Has new air filters and new cabin filters. Only seems to smell when driving at 55mph for about 20 minutes, the funk comes from the vents and in all heat/AC and fan modes seems to be less stinky in the winter.
Nothing is dead in the heater box because it does not stink in when driving around town and I have poured gallons of Lysol down the air intake during recic, open vent, etc, Smells like a mix of eggs, oil, and funk.
Dealership says it is not the catalytic converters as they "check out fine" Nissan dealership says it's bad gas, which is unlikely as when I drive away from home and I use other gas, it still smells.so what is it? What is it?
View 7 Replies
I've got a 2005 Nissan Frontier that has a roar and vibration that keeps getting worse over time. It happens as long as the car is rolling, but is the loudest at around 35 and 65 mph. From the driver seat is does sound like it's coming from the front passenger side. A few months ago I was driving across a curvy road and when I got home I could smell hot brakes. I checked, and the front passenger side caliper was stuck. I rebuilt the caliper, and that seemed to free up the wheel, but didn't fix the roar. I drove a couple more weeks and found the caliper stuck again. So this time I replaced it. The wheel has been fine since, but the roar is still present. After a while I figured it was a bad wheel bearing and replaced that too. But, that didn't work. I've also taken it to a shop and had them check the alignment, to which they said it was fine. I'm still racking my brain trying to figure this out.
View 5 Replies
My 1997 Saturn SL2 with 5 speed manual transmission won't shift into first or second gear. When I shift into the location where first would be the car is in third gear. It shifts into 4th, 5th and reverse just fine, though the shifter is in the wrong position for those gears. I can wiggle the shifter in neutral and get it to move into the position where 5th and reverse are normally found, but it is stiff and makes a clunking noise when I move the shifter over to the far right side.
I have removed the center console and the bushing appears to be intact. Both cables are in their proper positions inside the vehicle and at the engine. One of the cables (the top one in the engine) has some wear and tear on the boot, but does not appear to be binding. Other than the stiffness and the clunking noise, the shifter seems to be working fine too.
View 8 Replies
I have a 2003 Passat 1.8L with a M/T and 70K miles. For the last 6 months or so, I've found it hard to shift into 1st or 2nd gear when the car is in motion, even at slow speeds. When completely stopped, there is no problem shifting into any gear. I even had difficulty shifting into 2nd from 1st. Where to start troubleshooting?
View 1 Replies
Long time listener first time poster. My wife has a 2009 Vw jetta 2.5 with a manual transmission that is very hard to shift. It has 80,000 on it and has had the clutch replaced once. She told me that she never had any problems shifting until she let it sit for two weeks while she went to cape cod. I have driven it myself and can confirm that there is an issue. Sometimes it just will not go into gear. No grinding noise at all and very very stiff when moving the stick shift laterally from first to fifth. Not actually shifting from 1-5 just moving the stick across the range it feels like cement. I have already changed the transmission fluid and used the Vw oem oil. I also removed the shift boot and lubed all the moving parts with a high quality grease. Tomorrow I am going to bleed the clutch slave and have a good look at the shift linkage. Is their something I am missing?
View 5 Replies
I have a 2010 accent blue model with stick shift. been fine for 50k miles. Lately i have noticed an issue where i am in first gear and then when i push clutch in to go into second, the lever won't budge. it does eventually go in but it just isn't like it used to be. it happens say about 25% of the time. Since at higher rpms it won't do it but normal rpms it will.
Also, i just had a new short block installed, perhaps something is binding? If I sit in the car, stopped, i can shift into and out of all the gears perfectly. Maybe my 1st gear synchros are going?
View 2 Replies
I have a 2004 manual transmission Santa Fe. I've maintained it very well since new.
About 6 months ago I noticed it was getting difficult to manually shift gears. It wasn't grinding or anything, just "hard" to get it to go into the various gears while driving. Before, I could shift into any gear with just 2 fingers on the gearshift and it was smooth as silk.
I went in and had the gear oil changed. This was something I didn't even know needed to be changed and the guy said most people never do. They showed me the oil they took out and it looked more like black water than oil and smelled kinda funky. They changed the gear oil out, but still no difference, and in fact it's getting worse.
The best way to describe it is the only way I can really shift gears now is to find that "sweet spot speed" where the gears will change on their own (so to speak). I find it particularly difficult going from 1st to 2nd, such as when starting from a stop light. People almost rear-end me now as it takes me longer to get it into 2nd gear.
Once in gear it runs perfectly, no problems. The clutch seems to be working normally, except perhaps while stopped in 1st gear, it sometime seems to jerk a bit, and I find this most noticeable if I'm stuck in very slow moving heavy traffic with the constant stopping and then moving forward slightly and such.
It is almost impossible to "gear down" into a lower gear unless I'm at the speed where it would normally go into that lower gear on it's own. The best way to describe it is how it is possible to drive a standard transmission car WITHOUT a clutch if you shift at just the right time/speed. But I DO use my clutch, but if I'm not close to "that speed" it's really, really difficult to force it into another gear, and the few times I do try and force it, I'll often get a bit of grinding.
View 4 Replies
I went on vacation for a week and left my car at my parents house. I came back and now it has become extremely difficult to shift between gears. It's nearly impossible to get the car into reverse, extremely difficult to get it into first, makes a thud when pulling it out of first, is semi difficult to get into 2nd, but only a mild nuisance to get into 3rd through 6th.
For more information, the car is a 2012 Volkswagen GLI with just shy of 40,000 miles. The car ran just fine before I went on vacation and the car was not moved while I was on vacation. I did notice that a little ticking kind of sound when I had the car in neutral with no clutch. So the throw out bearing was starting to wear, but it was a very slight. But I haven't had any other problems.
View 13 Replies
I'm trying to diagnose a problem with my dad's 93 F250 7.3 diesel 4x4 with a ZF S5-42 5 speed manual transmission. It seems to not want to shift back into gear once the truck has warmed up, with 1st, 2nd and reverse being the toughest gears to get into. We've done a transmission fluid change with the required dextron/mercon substitute but the problem existed before the change and the change didn't seem to solve the problem any.
This problem didn't exist until I did a couple hundred miles of towing with it, some of which was done in 5th gear (overdrive?), so I'm hoping the 5th gear towing didn't ruin the transmission. From a cold start the transmission has no trouble shifting into any gear as well as with the engine off when either warm or cold, but with the engine idling and the truck at operating temperature it can be difficult to impossible to shift into gear, especially reverse.
I think heat has something to do with the problem because the shifts were worse a when its driven longer and during the tow/driving that was done in the last part of summer. It sat most of the time since then but we took it out today to test some things. Hot or cold the external hydraulic slave had roughly the same range of movement, but the drive line seems to jerk more noticeably like power is applied to it during a shift when its warm.
This all makes me think, even though the clutch hydraulic system is working like I think it should, that the clutch is not fully disengaging when at temp. I'm not a transmission guy so before I start throwing parts/labor at a problem.
View 8 Replies
I am experiencing a very frustrating shift anomaly. 2003 T and C . Under certain throttle conditions ( usually light ) from a dead start I am feeling a bump/violent shudder between the 1-2 transmission shift. If I let off the gas, I can get the shudder to quit and then by continuing to accelerate , successfully complete the 1-2 shift.
Does not happen all the time and never under straight ahead med-hard acceleration. By nature , happens most of the time under light acceleration when turning a corner from a dead stop. Sort of feels like a loss of traction or something funky happening with the torque convertor. Have serviced the trans with new fluid and filter, new TPS, new plugs, wires, and coil pack.
View 1 Replies
On a manual car, I know it's not the best thing to go from neutral, completely bypass 1st gear, and shift to 2nd gear. As well as 3rd to 5th bypassing 4th. However, is it the same for downshifting into neutral or another gear? Will it hurt the transmission to go from 3rd to neutral (bypassing 1st and 2nd) when coming to a stop? I do know that shifting from 4th to 2nd gear and bypassing 3rd will harm your tranny. I just want to double check if I'm right...
View 24 Replies
Ok so my transmission feels loose, too much play between the coast and drive side of the gears. Makes enough noise now that my wife complained about it so I'm looking into taking it to the dealer. I pretty much expect them to pass this off and do nothing, but its getting worse especially in the last couple of months.
Noticed a lot of play in there gearbox? Can you hear the gears make noise as they shift from coast to drive side?
View 13 Replies
My 2001 altima wont shift to high gear. driving around town seems to be ok, will driving on the highway be dangerous?
View 5 Replies
My wife and I purchased our 2005 Chrysler 300 Limited in May 2004.Our 300 has over 117,00 miles as of May 2011. It has been a rather dependable automobile.I have enjoyed it almost as much as my HD. We have performed maintenance as close to the schedule as possible.
I failed to drive the car as often as our second car is an used 2002 S430 which had been my primary auto until about two months. My niece and nephew reported to my wife that the car was not "doing something right". No one could really explain, so I had drove the vehicle myself to determine the issue. The transmission had the feel that it was being "slammed" into the next gear without any clutch. Once the car was warmed up, it appeared that when it shifted at 38-40 mph or 48-50 mph, the car shudders. It almost resembles the feeling you get when you run a car across those strips in the road.
I took the car to the dealership where I have had it serviced locally. They replaced a module which had Technical Service Bulletin from Chrysler for noted similar problems. The first module replaced did not resolve the problem. I took it back and they tried again with the end result being same as before I took the 300 into the shop, transmission appeared to shudder when shifting at the midrange gears.
The dealership as another option recommended that the transmission be replaced. I was not confident with their assessment as I had the distinct feeling they were not clear on the real issue.
I took the car to another service shop which I had more confidence in their work. I asked that they check the car for the problem with the transmission as I wanted their assessment. At this point, I had pretty much decided that I would get rid of the car, but did not want to give anybody else the troubled vehicle nor did I want to have to rush to decide on an automobile to purchase.
The second shop recommended the transmission be replaced, as well several other items be checked as there appeared to be oil leaks. The CAM plugs had been replaced as part of the service the dealer performed though the engine area had not been cleaned of the previous oil. That news was alarming, as the price estimate for a replacement engine was around 6500-7000 smackeroos, way outside of my comfort for repair on the car.
I was able to locate a used transmission with only 86k on it through a very gratuitous turn of fate. I digress, however, as the source for the used transmission was available only to licensed shops.
Two shops had referenced a transmission repair shop as one of the best in our small county. I left the car with the transmission shop for their testing, and it came back with their recommendation that the problem existed in either the coil or spark or an area related there.
I again took the car to the second shop and asked that they check the engine thoroughly for any issues with the spark plugs, wires or similarly related issues. The shop reported that the motor compression was at 190 across all six cylinder and the spark plugs and wires were new and there were no issues with the coils.
I am most happy that the engine is in excellent condition. I have planned to take the car back to the tranny shop as I reported the findings to him of the other shop. I am concerned about the transmission, though I am driving it about 60 miles round trip to work about 2-3 days each week. It still convulses at the mid-range shifting but otherwise runs pretty good after that. The car body is in very good shape as is the interior.
View 2 Replies
I have a '99 Nissan Frontier 4cyl. p'up and the air conditioner kept going off. The truck has three drivebelts, all inline. The first is Crankshaft to the Power steering pump , the second goes from Crankshaft to the water-pump & the alternator and the third one goes to the air-conditioning compressor; the one that keeps coming off my truck & shutting down the A.C. I replaced it three times and the last time it went off within a couple of miles. I know the crankshaft and the A.C. compressor pulley's are out of line and believe that's my problem. A mechanic friend of mine looked at it and said he thought it was something called a belt-leveler that keeps all the belts from slipping off.
View 2 Replies
It's a 2000 Frontier V6 4x4 CC with 104k miles. It just randomly dies going down the road. Sometimes it restarts. Sometimes it doesn't. Sometimes I just get a small blip (loss of spark or fuel - unsure which) when going down the road then it's fine again. It seems seems like a loose connection somewhere to me but I have checked and repaired everything I can find.
A little history of problems...
Fall 2014 - Fuel Sending Unit; I had similar problems a little over a year ago and I replaced this at ~90k miles. The stock one was corroded and the fuel pump wasn't getting power. Got the part from Nissan directly. Truck ran great for a year then started having same issues in fall of 2015. I am thinking this couldn't have gone bad again in only a year, but who knows? No engine codes at the time.
December 2015 - Distributor #1; I replaced it with one from Auto Zone. Had the same problems that day. Returned that and replaced with one from Napa Distributor #2 (New - house brand - supposedly made by Altrom - which is supposedly comparable to OEM) This seemed to fix it for a little while. At the same time I did the timing belt, spark plugs, wires, valve cover gaskets, a bunch of suspension work, etc. so I had the harness off. Did I knock something loose? I feel like I have checked it up and down.... doesn't seem that way.
January 2016 Bad Wire?; Same issues. Wiggling the harness into the distributor seemed to have an effect on restarting so I pulled the harness apart from the dist to the main and found a small cut on the casing of one of the ground wires. The wire was not damaged, just casing. Fixed that with a double layer of shrink tube and it ran fine again for a couple weeks. In this same period my catalytic converters also went bad. My exhaust manifolds cracked, next thing I knew I had catalytic converter codes on both sides of the engine. Ran it like this for a few months.
April 2016 Distrbutor #3 Same problem. Randomly dies. Gets progressively worse over a couple day period. I gave up and took it to a shop (Downing St. Garage in Denver, CO) They diagnosed it as a bad distributor so I had it replaced AGAIN (they were nice enough to use the Napa part I bought and get a free warranty part)
June 2016 Distributor #4 Same problem again. Still have not replaced cats - did not want to spend the money when the ignition problem seems un-related. Replaced distributor with another warranty part from NAPA. This time the one that I took off made a crunching sound when you turned it by hand.
August 2016 Finally replaced cats. CEL codes were gone for an afternoon then the truck started sputtering down the road again... CEL P1320 and CEL P0325 BACK AGAIN!
I am at a loss on what to do. I have read that the MAF sensor can get dirty... but this doesn't seem to explain the P1320. Anyway, I ordered some cleaner, a new knock sensor and another distributor (this time Nissan brand but re-manufactured... they no longer sell new ones.)
View 4 Replies
Our mechanic is stumped. The Frontier runs hot when idling. The clutch fan and thermostat have been replaced. The radiator has been flushed. When you are driving or you turn off the A/C, the temp goes down. The next suggestion is to replace the radiator, but I'm already hundreds into this so I hate to do anything else unless I'm pretty sure it is going to fix it.
We do know that the catalytic converter needs replacing. Could this have anything to do with it?
View 5 Replies
