Nissan :: 2000 - Belts Change Caused The Power Loss
Dec 27, 2012
I have a 2000 Nissan Xterra 3.3L, at 114,000 miles I changed all the belts two days ago these being 3 serpentine accessory belts and the timing belt with tensioner. I do believe that the engine did not move (cams & crank) while replacing timing belt and even made sure the timing marks all lined up on the cams and the crank upon installation. The belt tension on timing belt was done to Chilton Spec. as well. I did not tighten the serpentines to spec. , but just to best judgment. Between idle -to- 3000 the engine does not seem as strong especially up hill. It idles smooth, does not overheat and there is no tapping/knocking or a check engine light. I was told that that with new belts (especially the timing belt) the motor may have to wear to the belts or vice versa and there may be some power loss till all wears in together do to now tighter tolerances. I was going to relieve some tension on the serpentines to see if maybe that would make a difference in regaining power.
View 14 Replies
Advertisement
My Nissan Maxima GLE 2000 is showing CEL with code of P1320 ONLY, and the car is running rough/or loss of power. The shop that checked for the code advised that it could be something related to Ignition, and also provided me with the system generated list of reasons for the code. Before I decide to do anything, I wanted to check what option I have to address this in a most cost effective manner:
1) Is there a quick way to check which coil would have gone bad ?
2) Is it advisable to change 1 LH and 1RH at a time, and see if it fixes the problem ?
3) Could it be cam shaft sensor that could have gone bad ? Are there any symptoms of cam shaft sensor failure to isolate it to one way or the other ?
View 1 Replies
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
View 4 Replies
I had my oil changed at 40,000. I am at 42,500 right now . My " change oil soon light " . Seem like a little soon ! Plus I am 5 hours from home on a ski trip. I have checked oil level it fine. Will I be fine to drive it home 5 hours back to my local dealership for oil change? Or should I find a place up here? What would cause the light to come on so soon ? I am new to this truck . My old 7.3 did not have all the BS that this truck has .
View 6 Replies
I have a Nissan pulsar n16 (almera) auto. About 8 months ago I was driving on freeway, had loss of power at high speed and felt like it was going to stall. When I accelerated it jerked a bit and kept losing more power each time I pushed the accelerator. Actually felt like I was braking slightly. There was also a large cloud of smoke that came out. Since then I have kept taking back to mechanic and each time something replaced to fix problem but still occurring as well as oil consumption, previously NEVER used oil. So far I've had replaced:
Fuel pump
Starter motor
Finally motor rebuild a month ago due to to broken piston ring, which was meant to be the cause of all the problems.I am still having the same problems and just noticed again oil was nearly empty. What else it could be?Catalytic converter? Ignition leads?If my motor was rebuilt could it be something else using the oil? Or are these symptoms of a other underlying problem that is causing all these?When my motor was pulled apart I was told was in very good condition apart from broken ring.
View 19 Replies
My 1994 Nissan Altima is a great little car with an unknown number of miles, though my best estimate is around 150k. Every time the air conditioner compressor kicks in it drags the engine down significantly when at idle, and often causes the belt to squeal. The squeal is most notable while accelerating. My question is, since the belt is relatively new do I have a tensioner problem, a compressor problem, or something else?
View 4 Replies
Truck has been running like a champ the entire time I had it. Took it in yesterday for an oil change. They also changed the fuel and air filters.
Drove off the lot and noticed some loss of power. This morning truck still feels sluggish but it is also blowing out black smoke pretty much every time I touch the gas pedal. I am even being super gentle with it. Starting from a stop, I hit 1500rpm and it's blowing thick black smoke as if I was flooring it. Same thing while rolling to get a bit more speed to pass.
View 13 Replies
'04 Nissan Pathfinder 3.5L ~150k: P0011 and P0021
Friend's vehicle. OBD-II codes indicate Intake Valve Timing Control Bank1 and Bank2. Vehicle drives OK most of the time, but then has lapses of lost power where you step on the gas and the vehicle doesn't accelerate accordingly. RPMs rise, but tranny doesn't seem to shift at the right time. Overdrive button OFF doesn't seem to have any affect. Codes have been erased and returned the next day.
Is this Camshaft-related, as in Camshaft Position sensor? I had this issue with my '97 Taurus, but in that case it threw the code explicitly for the CMP sensor.
View 1 Replies
The timing belt broke on my aveo, destroying the engine. I replaced the engine with a used one. Now I get the car back on the road and the automatic transmission won't shift from 3rd gear into 4th. Is it possible this problem was caused when the new engine was installed, or the transmission was damaged when the timing belt broke?
View 4 Replies
I have a F350 that has intermittent power loss.
View 14 Replies
I pulled with my 2000 F250 7.3 for the first time yesterday pulling a 12,500 5th wheel and then again today with an 18 ft ski boat weighting around 3500 for both the trailer and boat. I had this same issue pulling both.
Today when pulling the boat/trailer i was behind a slow moving truck and when we hit a hill with a passing lane i merged over and wanted to start passing him. We started off at around 45 mph up the hill and as I started pushing the pedal I wasn't gaining any speed and my rpm's didn't even get over 1500. It felt like a stall and continued that at around 45-50 mph up the hill (about a 65 degree slope). When I'm not towing the truck runs great, plenty of power and averaging around 16 1/2 mpg.
Only mods i have is a 6647 Napa filter, muffler delete and it's running the same 4 position TS tuner from the original owner. During normal operation I run it at the 75hp gain and when towing i use the 50hp gain.
In both instances i could see black smoke coming from exhaust when pushing the pedal but my rpm's wouldn't go up and truck maintained the slow speed going up the hill. Once at the top it drove normal and picked up speed without any problems.
View 14 Replies
I've got a 2000 F-250 with a 7.3. The other day I was driving down the road and it lost power and my foot almost went to the floor. I was at the bottom of a hill when it did this and I was running 60 mph. By the time I got to the top I was running 20 mph and had the truck to the floor. When I was driving it home it was tacking around 1800 rpm and my egts were only at 125 degrees. I know I'm not getting fuel. I thought it could be the fuel filter so I changed it. Still no luck. It'll start back up but it dies if I take my foot off the accelerator. It shook terrible when I was driving it home too. Is it injectors, uvch, hpop, or something else?
View 14 Replies
My son has a 2000 S10 that runs alright as long as he only drives it about 20 miles one way, the problem seems to occur after he goes on longer trips, closer to a 45 or 60 mile drive, and it seems to happen when he comes to a stop, at a red light, or stop sign, the other day I drove it to my daughters house which is a 45 minute drive, we stopped several times, before I made it to her house, just when I though we were going to make it with no problems, I come to a stop at a red light, when I start to pull off the truck becomes so sluggish, that the truck motor can barely keep running, when I let off of the gas it seemed to pick up power, but every time I pressed the gas it would bog back down, I barely made it across the intersection, trying to get to a parking lot, when the power is just to low to pull any more, so I leave it running, but put it in park, so my wife can get behind the wheel, thinking, that if she presses the gas, while I push it, we can make it to the parking lot.
Well as soon as I got behind the truck, I tell her to put it in gear, and press the gas, while I push, well the truck takes off and she drives it in the parking lot, I walk on up to were she had parked, there was a burned rubbery, or oil smell coming from the truck, not should which, I’m checking everything out, when I take the power steering cap off, it releases air out of it, like there was press build up in it, after that I crank the truck back up, and drive it to my daughters house, and back home with no more problems, the check engine light came on when this happen, but has now gone back out, now, like nothing is wrong, what could cause this? I have check everything maintenance wise and everything is in good working order it doesn't run hot, it has the right oil pressure and amount of oil in it, has the right amount of transmission fluid and power steering fluid, I took it to a mechanic, but he said he didn't find anything wrong with it, and told me to just drive it, till what ever was causing this tore up.
View 4 Replies
Mine broke on the throttle body end, I think the cruise control motion caused the throttle cable to bind up as it pulled to accelerate probably over a long period of time. It is a 2000 Mountaineer V8 part is not obsolete from Ford other than a JY what other new sources are there? I was informed only 99-00 are the same from Dealer and have searched via Google. I already fixed it with new 1/8 steel cable and swedged ends, I want a new one just in case liner is gone south.
View 1 Replies
I have a 2000 gmc jimmy 300.000 km 4.3 vortec .starts ok, even when cold idle smooth but when I accelerate past 2000 rpm it has a complete loss of power. I bought a fuel pressure tester key on 2 seconds 60 psi when I start the vehicle and running 55 psi. I took it on a road test it stays at 55 psi and has a hard acceleration and will go to 60 psi ,and then starts to break up my first question is how can I block off the return line to the tank, there's no rubber hose in any of the connections just steel lines and hard plastic with push connectors, is there a plug that you can buy or how I can block off the return to see if the pump will build pressure to 75 psi to 80 psi will this will tell me whether the pressure regulator is faulty or the fuel pump needs to be replaced.
I have a manual its a Haynes for chevy blazer gmc from 95 to 2004 it says with central sequential fuel injections (csefi) key on engine not running it should be approx 55-61 psi the engines running at idle it should decrease through 3 to 10 psi according to this manual i am within range but i have read on other posts that it should be 60-65 would you say that my 55 psi reading is okay? or should it be 60-65? also when i blocked the return line should i get a reading of 75 or higher? if the reading goes up does that mean that the fuel regulator is faulty? and if it doesn't go up does that confirm that the fuel pump is the issue?
View 3 Replies
So, I have a 2000 Hyundai Accent that has had the CEL light on ever since I have owned it (about 7 months). I was told it was the O2 sensor and did not have it scanned. Occasionally, it would lose power and the CEL would blink. After I would take my foot off of the pedal and baby it for a sec it would usually go solid again and drive okay. About 2 weeks ago it started blinking constantly and it sputters and drives like sh*t. Now, I know that I should take it to Autozone or someplace so that they can tell me which cylinder is misfiring and all, but it is really sketchy to drive. I put NGK spark plugs in it today with no change. I ordered plug wires and a coil pack to see if that straightens out the problem. If it doesn't then I am going to lean towards intake gasket or perhaps a missing or bad o-ring at an injector. So, does this sound like a reasonable plan of attack to get rid of the blinking CEL (misfire) and restore my Accent back to all of its craptastic glory?
View 2 Replies
I have an 05 accent and about 6 months ago I started to notice a clicking sound coming from the belts area ( it sounds exactly like a BBQ grill igniter when it's pressed), the sound starts as soon as I start the car and stays pretty much the whole time, I had the car lifted by my mechanic and he discovered the problem in one of the belts ( not sure what is called but it's the one at the very bottom of the belts, the first one you see when you lift the car ), the spark is seen at the edge of the pulley or where the belt sits on the pulley. The mechanic was puzzled about this, he recommended replacing the crank sensor as a first step, the car runs fine and there is no other symptoms or issues
View 2 Replies
The wife was stopped at a light in her 2006 S60 and when the light changed and she accelerated the car stalled and died. It would not start and thus I had it flatbedded back to the house. Id been told at the dealer during a service trip ($$$) that the alternator might be going bad as it was making a whirring noise and was given an estimate to replace it, the serperntine, pulley, etc.. of $1300. At the time it wasnt a driveability problem and being a working stiff I didnt have the 1300 to spend so I decided against doing the work. Thus, when the car stalled I figured it would be the alternator causing the problem and draining the battery.
I recharged the battery overnight figuring I could get the car turned on then remove one of the battery terminals to verify faulty alternator. However, car would not turn over, Id only get what sounded like a click from the starter. Fine, I figured, the alt killed the battery so I went and purchased a new one and installed it. Car would still not start and Id still get the click from what I believe is the starter. Tried the old bang the starter with a hammer and still nothing. Checked the connectors to the starter and all seemed ok.
At this point, the dreaded "my wife seized the engine" thought popped in my head. I then tugged a bit on the serpentine and noticed the crank turn slightly so Im pretty sure she didnt seize the engine. (fingers still crossed on that one).
View 2 Replies
My wife's 2000 grand am 2.4L engine is acting really funny. this is the first problem we've had with it. i was driving it to pick up my kids from school. on the way i stopped and got some gas from the marathon then drove about 5minutes and it started running really ruff lose of power wouldn't go above 30mph seemed like the transmission took longer to shifter to.
i made it to the school as i was about 2 1/2 blocks away. got my kids check the oil and it was really low so i got 2 quarts as it was a gas station in walking distance. i thought it was a lil better but i started driving it and it had the same results. i got it home about a 10minute trip regularly and parked it.
the next day day it ran then stumbled hard. and every time i tried to start it got the same think was like a lock up. it did crank but when it tried to start it stumbled or locked up. i pulled the plugs had some wet threads oil was on the first on and the threads and around the spark plug b4 i pulled it out.
2 of the other plugs had red stuff on them not on the threads though. here are some pictures also i will show a vid of what its doing. i did a compression test and here are the numbers starting with the first one with oil on threads.
190-194-200-190+ compression test with cold engine.
Also smoked puffed up not sure from where yet..
View 19 Replies
I've got my sister's 1995 Dodge Neon with the 2.0L SOHC. While driving it recently I heard a horrible squeaking noise then a ZZZZZZzzzzzz sound. I immediately pulled over. The check engine light came on, and I shut the car off. Coolant was all over the place leading me to believe the water pump failed. I had it towed to my house, and now I will have it towed to the shop to get fixed. I would like to have them repair the timing belt and water pump. However, I am afraid that the valves were beaten to a pulp and now I will need a new engine. I was only going 35 mph when it happened. What are the odds that my valves were smashed up, and is there anything I can do to check them before I pay for a timing belt/water pump repair?
View 19 Replies
I have a 2000 Dodge Caravan SE 3.3L. The timing chain recently broke. So I replaced the timing set, cover, water pump, camshaft sensor, and oil pan. The timing is all aligned. It starts right up, but then stalls. Unplugged the front three spark plugs to see if one of those were the problem, and then it ran better and didn't stall out.
View 3 Replies
