Monte Carlo :: 2003 SS - Intake Manifold Gasket Replacement
Aug 16, 2011
I took my Monte in for the annual Missouri Safety Inspection. Note: I had no known problems with my 2003 Monte SS 117K Miles. After the inspection, which passed, I was informed of a variety of problems: Intake Manifold Gasket Replacement, Valve Cover Gasket w/Intake replacement, Thermostat w/Intake Removal, Fuel Injector O-Rings w/Intake Removal.
My question is should I have all of this done? It's not cheap..roughly 1000 bucks. I know very little about this and I don't want to just tell my mechanic to do it without some research. Are these common problems with Monte's of this age/mileage and just part of the cost of owning this car. I am the original owner and have avoiding costly repairs/maintenance..it's been a great car.
View 4 Replies
Advertisement
Turned the key on my 2002 MC SS, V6, 3.8L, and the Intake Manifold exploded.
Intake Manifold Exploding on a GM V6, 3.8L? It sounded like a 12ga shotgun. Fortunately no one was looking into the engine compartment at the time as they likely would have been killed given the amount of shrapnel from this explosion. Note that the explosion was powerful enough to blow off the oil cap, which is screwed on with very thick threads.
The vehicle was at my mechanics at time and in his forty years he's not seen an intake manifold explode save for those residing on Top Fuel or Funny Cars.
View 1 Replies
Replaced intake gaskets , used the rocker arm tool to take out push rods, put it all back together now, the check engine light came on and its telling me my timing is off.
View 7 Replies
I've got a 1997 F150 with the 4.2L V6. Before I got it last summer I did some research, but apparently missed the issue with the intake manifold gasket leaks on these early engines. It seems to be a very slow leak, but obviously I want to get it fixed. I called Ford to see if it had had the recall work done on it, but all they could tell me is that there wasn't an open recall on my truck (with the exception of the recent fuel tank strap recall). Their system apparently only goes back 10 years, so they couldn't even see the freakin' recall. So, I've got a few questions:
1) I know I didn't post much info, but does this seem like an intake manifold leak?
2) Are there any special tools needed to change out the gasket myself?
3) Can you all recommend any replacement gaskets? I found a few different manufacturers of gaskets, but I'm sure some are better than others.
4) Can this issue cause the computer to throw the loose gas cap code (P0455 if I recall correctly).
5) Would it be worth it to just get a new truck? I really wanted a diesel in the first place, but I also hate to give up on a nice truck with only 115,000 miles.
View 6 Replies
just got finished putting her back together from a blown intake manifold gasket and run for a few miles to get rid of any cob webs and then my battery light comes on. just replaced the battery last week. and I tested the alternator and it charging at 14.5 volts bat reads when disconnected 12.9 volts so I am not sure why my battery light will come on.
View 14 Replies
I have been having some issues with my 97 ford f150 4.6 liter, started out running rough, then hydrolocked with no serious damage, blown intake manifold gasket, fixed that, alternator over charging do to bad voltage regulator, fixed that. and airbag code 52, still working on that, as well as failure to connect when trying to do diagnostic scan. now I am wondering if the engine diagnostic is still even working. still running good just a very slight vibration when warms up. I am not getting any code. or my check engine light is not showing any codes. What I want to do is force a code. What would be the safest way to force a code or force engine light to give a code?
View 6 Replies
I am about to replace the intake manifold and gaskets. I know all of that process, but first question is if there is anything i should do whilst in there. Second question; what can I do with my intake to get more power? Mainly just kind of wondering before I get my parts ordered.
View 4 Replies
Well, I decided to take on the dreaded task of replacing the lower manifold intake gaskets and put in new isolator bolts. It was a major undertaking, and when I finally finished the oil change and fired up the car, it sounded fine. Then I checked under the hood.
I saw coolant spurting out the side of one of the hose connections that I had to take off and put back on. I thought the gasket on it looked pretty worn, but wasn't expecting this!
Unfortunately I don't know the name of the hose connection to pick up a gasket at the store ... it's the larger lower hose that is bolted on to the lower intake, not the hose slightly above it that has the plastic clips.
What is the name of this hose connection so I can try and find one at the store? It's a 2003 Windstar model.
View 3 Replies
I have a 98 f150 4.6 4x4 with 175.000 miles, I suspected the intake gasket is leaking, I'v never done this before. What is involved with this type of repair? Will the intake gasket leak bad enough to leak antifreeze on the floor? Is it okay to continue to drive with this problem? Bad weather is on the way.
View 7 Replies
I have a 2003 Explorer with the 4.0 K motor. It has a vacuum leak and the check engine light will come on from time to time. My work buddy has a high end computer and it showed that the driver side bank was running lean. The computer showed the O2 sensors to be working fine, and I replaced the PCV valve. All other vacuum line appear to be in good condition and I tried the spray test with the break cleaner with the motor running. This is leading me to believe the air intake gaskets where due for replacement. Here is my problem, I can not get the last bolt out of the plenum. The one on the driver side up against the fire wall. I tried to remove the cowl in order to get a straight shot at it but I can not get the seem seal to break free.
View 4 Replies
On a 1997 Nissan pickup 241,000 mile 2.4 liter. What are the signs of a bad manifold gasket. How can i test it.
View 6 Replies
The air coming out the right front vents is cold; but, the air coming out the left front vents (driver's side) is warm. Sliding left ac slider switch up and down did no good. Considered fuse, but both left and right AC controls run through same fuse. Suspect bad motor for left side plenum duct, or bad connection, or faulty vacuum at motor (if motor is vacuum actuated). Considering removing dash cover to see if I can find the motor, but not sure how to remove dash cover, or even if that's the way to find the motor.
View 7 Replies
The engine fan in my 2003 MC SS doesn't seem to be working and the car is starting to overheat. The other fan, which I think is the A/C fan seems to be working okay. I know nothing about cars and before I take this to a mechanic. I do not want to go somewhere and get totally ripped off. So it would be nice if I appear to know what I am talking about... when I take it to the mechanic.
View 2 Replies
Leaking intake manifold gaskets on General Motors 3.1L V6 engines? Mine is a 1998 Grand Am with low milage (40K) and I have been told I need to spend $900 to replace the intake manifold gasket because it is leaking antifreeze into the engine oil.
View 8 Replies
I have a fudged-up looking oil leak that my oil change guy says is probably a blown intake manifold gasket. Is this the same as a head gasket? I thought a head gasket was around the pistons. I see there is a product on the market that you can put into your radiator that plugs up leaks in the head gasket (Steel something). Is this an OK fix? It would cost $90 for a bottle of the stuff. And what is a reasonable, or low, rate to replace this gasket? And, how long can I drive the car with this condition? It has lost a quart of oil in the past month, driving about 600 miles.
View 3 Replies
I needed to replace the intake manifold gasket on my 2002 f250 v10. Tore everything apart put the new gasket in which was the same as the old one lyrics to notice something isn't right. I have been driving the truck for over 10 years like this. Is it OK to just continue bolting everything down and go on like this? I am guessing the prior owner 10 plus years ago put the wrong intake on. I keep looking up intakes but they all look just like the one I have. Also that port exposed is on the back passenger side.
View 3 Replies
Looking for any pictures or directions on replacing the intake manifold on the 2004 F150, 5.4. Got all the parts with the pulgs, and ignition coils.
View 6 Replies
Just today,when replacing the UIM on a naturally aspirated 95 Pontiac Bonneville 3.8 with a Dorman upgraded type from my local auto parts, I ran into an issue. When following specified torquing sequences and specs , be very careful with the 1 long stud (#7), as it will split your new manifold there if you try to torque to 89 in/lbs. Took 1st back for replacement ,and the second new one started to split at the same place. Was using a brand new Craftsman in/lb torque wrench set correctly and following instructions exactly. I've seen a lot of excellent info on this UIM issue with the GM 3.8 ltr 1995-2004 years, but never this issue with the replacement ones. If I have to change this again will definitely go with the aluminum one.
View 1 Replies
I have had a problem with my car idle hunting for about the past year. Last week my car threw a code and my code checker said that all 4 cylinders were misfiring. So I am still under warranty and took the car to the dealer. They said the intake manifold was leaking.
Two questions come to mind: Has to engine suffered any damage from leaking for over a year? and Do they automatically change the oil when changing out the intake manifold/gasket?
I did have an oil analysis last year (5/11) through Blackstone Labs and no antifreeze was present in the oil but the silicates were mildly high. Car is a 2005 toyota corolla with 102,xxx miles. The dealer also did the head gasket and a couple other engine gaskets 1 year ago.
View 15 Replies
I have a 1998 chevy silverado z/71 4x4. I had a water leak and had the intake manifold gaskets replaced. Ever since then, the check engine light comes on and it soots up the o2 sensors and the 4 plugs on the right bank. It may run good for a month or so and then it starts all over again.
View 1 Replies
I have a 95 Monte Carlo LS it has 53,000 miles and When I go to give it gas it hesitates and the rpm goes down and then I let off the gas and do it slowly and its fine. Why this is happening all of a sudden. And my check engine light is on.
View 1 Replies
