Mitsubishi - Mirage :: Hesitation Accompanied By CEL Coming On And Then Going Out
Aug 31, 2014
Got a 1997 Mitsubishi Mirage with this code 0420. Only had car a while. It has always had a hesitation accompanied by the CEL coming on and then going out. Might happen twice a trip and then not occur for weeks. Previous owner said they failed an emissions because he cleared a set code(not told to me). The car dives fine and gas mileage seems to be fine. Car does use about a quart of oil over a 3000 mile oil change. It also has/had a rattle similar to an exhaust baffle...the rattle is not an every trip occurrence either.
Had Autozone check for code and was told catalytic converter needed to be replaced. There are no emissions in my state but I would like to know any opinions on my problem and any issues with driving car without repair. I think I want to clear code by disconnecting battery cable and see if it returns but not that would be a good idea. Also considered buying a scan tool with live data to see if there is another issue that might not involve replacing the catalytic converter. Previous owner also mentioned a hissing when removing gas cap and he bought another cap but the I still notice the hissing.
View 4 Replies
Advertisement
This car has the 1.5 liter 12 valve motor and a five speed transmission. Ran pretty good until a few days ago when it died. the next day it started up and ran ok for about a half a block and then I had to pump the gas to keep it running. I had bought gas at a dinky budget station that I had never been to before so I suspected bad gas and I put in a new fuel filter which did not work. I then put some Seafoam additive in. After I got it started I revved it up a bit to try and clear things out and then let it idle for an hour or so.
The engine smoothed right out and didn't idle rough but did not start after I turned it off. I pulled a plug wire, put in a bolt and tested for spark against the valve cover. Not even a weak spark, nothing. I looked for the coil but there is no coil and I am told that the coil is in the distributor. I also saw a reference online about the crankshaft sensor possibly being the culprit. What a crankshaft sensor looks like and the engine compartment is so crowded with hoses, wires and all kinds of things it is real hard to see anything from above.
I am wondering if the coil is bad do you have to get a whole distributor ( I was quoted a price of $269 for a new one) or can you take it out of the distributor and replace just the coil.I have a brand new 154 piece Craftsman tool kit, but I am 62 years old and back when I learned how to work on cars it was a lot simpler. Now when I open a hood about half the stuff there is unfamiliar to me. My other vehicle (Chevy C20 van) is not running that great and gets awful gas mileage. The battery is new and I have never ran out of gas with this car, so they are not suspect.
View 1 Replies
91 Mirage starts and runs ok but usually will not start again after warming up. What are the possible causes and how do I check to eliminate dead end cures.
View 3 Replies
My 2000 Mirage (with 145,000 miles) no longer stays in 2nd gear. Due to the age of the car I do not want to replace the transmission but I would like to get a few more months out of the car. For now I am just shifting from 1st to 3rd. My questions are;
(1) Is there anything I can do short or replacing the transmission to get 2nd gear back,
(2) if I don't do anything to fix the transmission is there any reason I should not continue skipping 2nd gear until something else breaks and
(3) is there anything I should do like flush the transmission to try to extend its life?
View 3 Replies
I can not resolve a rough idle in gear when engine is warm problem. I've replaced plugs, wires, mounts, isc, o2 sensor, ecu, have no codes.
View 17 Replies
I have a 2000 Mitsubishi Mirage. I've been having issues with judder. I first mentioned it to a mechanic late last spring, but they said the rotors and pads were fine, so I let it be, and the judder got gradually worse, until I brought it in again a couple weeks ago and got new front rotors (the rotors were warped at that point, and barely within spec). But as I left the mechanic's, I realized that the judder had not gone away, it had just changed, and become more pronounced. (Yes, I should have gone right back in to the mechanic, but I was peeved that the problem was still there, and sleep deprived from working 3rd shift.)
The judder is most noticeable when I am stopping in town. The car behaves as if I'm stomping on the brake repeatedly; the brakes are grabbing and releasing, grabbing and releasing. Until the past week, this has meant that my head bobs front and back a bit as I stop. In the past week though, it feels like there is a tiny bit of side-to-side movement developing, too. The steering wheel does not shake, and I can't feel anything unusual in the pedal.(Also, if it matters, the tires were rotated about a week before the rotors were replaced.)
What could the issue be here? Should I take it back to the shop and ask them to undo and redo the lug nuts by hand, since I've read that overtightening, or tightening in the wrong order, could be an issue? Should I ask them if they test run-out when they install rotors? Should I go to a different mechanic? The mechanic I went to is a local large operation with a decent reputation, but... I've gotten some conflicting information from them, depending on who I talk to. Also, should the pads have been replaced along with the rotors? They're at around 70%.
View 9 Replies
I'm sure this popping sound coming from both sides of the front wheels is a serious problem because it happened to my dad's car before. The only thing is that i want to fix it before it gets serious and pops off one day while I'm driving.When ever i turn, about 95% if not 100% of the time, i would hear the popping sound from one side of the front wheel. I want to know how much it usually takes to fix and if its possible for me to fix it myself with almost no knowledge of fixing cars.
View 8 Replies
Details. I was driving my car yesterday. It stop as i gave it fuel to go around a corner.Its a 95 mitsubishi mirage s manufacture october 94 in japan. Its a manual turned the key. Nothing but cranking and flooding. My friend came to take a look at it. no spark.I smelled fuel and have still almost half a tank which mean its pumping but no spark came from the ignition wire.I have replaced the rotor and am waiting on new ignition wires and distro cap. When i took off the distro cap I didn't see any visible cracks.
View 9 Replies
My 2015 Mitsubishi Mirage had a strange little incident the other day. I have posted this on the forum for these cars and as far as the people on that site know, I am the first to experience this exact issue. I also called the Mitsubishi dealer and they said this would be under warranty if it happened again. They said they had never experienced an issue like this in the Mirage either. Whatever this is isn't a common problem which is good and bad.
I was pulling out into traffic and then there was a sudden momentary loss of power and then power returned. The check engine and traction control light were on. I pulled into another parking lot and when I came out, the check engine light was on but the traction light was off. I put the car in reverse to backup and it stalled. There was an Autozone across the street so I took it over there and had the code read. The P0068 appears to be a mismatch in input from the MAF, MAP, or TPS sensors.
I was low on gas but not that low so I went across the street to a gas station. While the car was filling up opened the hood and unplugged/replugged any wiring connectors going to sensors around the intake and manifold, wondering if it was a bad connection. The car took about 7.5 gallon of gas. These hold like 9.2 gallons or something.
I got in and started the car and there was no more check engine light. I hadn't cleared the code so that wasn't why. Anyway, I have been driving the car like normal the past 3 days with no repeats of the behavior.
I figure that a connector might have been loose from the factory or after the repairs from when I hit a deer a few months back. The car sustained front end and side damage so maybe something wasn't plugged in snug enough after the work.
I guess I could have had a bad tank of gas and was starting to suck moisture or something. I would have thought that would have triggered a misfire or something so my guess leans to a loose connection. The CEL went away immediately when I started the car. The new tank of gas would have at least taken several seconds to have any impact.
View 5 Replies
I'm writing to ask a question about my 1997 Mitsubishi Mirage. It has 98,000 miles on it. I had my transmission fluid changed at my regular shop about six months (2,000 miles) ago.
For the past six to eight weeks, I have noticed that a light grinding sound comes from the bottom of the engine compartment. This sound happens briefly, for about 0.5 to 1.0 seconds, when the transmission shifts from first to second. I can try to find previous maintenance records if it's relevant.
My question is, is it worth it to change the transmission fluid again? Is it possible that will take care of this? Are there any homeopathic cures?
I will note that the owner's manual calls for "Mitsubishi Diamond ATF SP-II." The shop didn't have it, so I recommended a Valvoline ATF designed for imports, based on some searching?
So a second question is, would it be worth it to take this to the Mitsubishi dealer to get the official fluid?
View 1 Replies
I just bought a used automatic MM with 137k miles. Engine and interior super clean. I did test drive and it seemed to pull back a bit and rev harder when I was starting out from a stop or in intermittent traffic where I was slowing down and speeding up with flow of traffic. It also does it worse on hills. The guy from the car lot said it was the way I was driving the car...hmmmm...I'm not a lead foot. I let the car ease into higher speeds, I don't punch it. Ever.
Yesterday I took a longer drive and had other people in the car with me who also noticed the rough transitions between low gears and asked if that was "normal." NOT being a car mechanic I get alarmed when others are pointing something I too thought could be at issue. I bought the car "as is" after doing some online research and finding out that these car's even at this age get 4.5 to 5 star ratings from people who have them.
I took it to Auto Zone and they put the little code reader on the car but no codes came up. His suggestion was to have all the fluids changed in case someone put the wrong weight of transmission fluid in the car. I did check the fluid at the car lot and it was bright pink and at correct levels. Not sure that's what it is. He also suggested the possibility of it being a "shift cellinoid"?
I don't know what that is but he said it shouldn't be expensive to fix. He also suggested getting the transmission serviced to see if that might solve it. Someone else suggested "clean the IAC hole and throttle plate with choke cleaner..." don't know what that is? Someone else said to consider a vacuum leak in the fresh air tube between the air filter box and the throttle body...these are all just guesses.
View 1 Replies
I own a 1998 Mitsubishi Mirage with about 190,000 miles on it. The engine light has started coming on and I get three codes:
P0170 Fuel Trim Bank 1P0136 Oxygen Sensor Bank 1 Sensor 2P0301 Cylinder 1 misfire
Read more: [URL] ....
View 1 Replies
When driving, no matter what the speed we get intermittent hesitation from the engine. Usually lasts less than 30 seconds. Today lasted 7 miles. Doesn't matter how long I've been driving. Does it whether the car is cold or warmed up. Was told the engine air filter needs cleaning. What this could be?
View 3 Replies
My 98 Mitsubishi Carisma (similar to a Lancer) has a problem when engine cold, the engine seems to hesitate and sputter, and if I try to put it in gear it will only go very slowly. Once the engine is warmed up enough the problem goes away, whats causing this? Its an old car and I don't want to spend a lot to repair it.
View 2 Replies
Recently I installed a GTA bluetooth system (about 4 months ago) and recently there is a squeaking noise coming from the passenger side. It almost sounds like an AC compressor issue (had the same problem with my F-250) but there is also an accompanying "gurgling" sound as well. AC problems with the Gen 2 after 160,000 miles?
View 7 Replies
I have a ticking noise coming from my engine, its the loudest when cold, it only happens at about 1800 rpm and up, and it only happens when I'm pressing on the gas pedal. I looked around my engine, and the noise seemed like it was coming from my fuel injectors, however, the noise doesn't change speed. Can it still be my fuel injectors? or is it something else?
The car is a 1996 Mitsubishi 3000 GT Base (non-turbo), 5-speed manual.
View 6 Replies
I own a Lancer Evolution X and I've been having a strange issue where, when accelerating around 2500-3500 rpm a thick cloud of blueish smoke starts pouring from the exhaust for about a second or two accompanied by a loss in power. The smoke stops quickly and then it runs like normal. This only happens once in a while for a second or two. When idling there is no smoke. Or at Wot. There is no coolant mixing with oil. The oil was recently changed with the proper oil. and it still happens once in a while. I checked the turbo and there is no shaft play or oil inside of it. There is no loss of boost. Although I did see a tiny pool of oil near the turbo inlet and some more oil coating the inside of the intake pipe. is it possible that the turbo just sucks up some oil that collects at the end of the intake? the PCV line which connects to the intake appears to be letting some oil into the intake.
View 7 Replies
I've got a 2008 Mitsubishi lancer. I've noticed a gradual vibration coming from the front suspension. At first I could just hear it, but now I can feel it in my steering wheel and a little in my pedals. It doesn't vibrate when I accelerate, nor does it vibrate (too badly) when I brake, but when I'm holding the speed consistent, or letting off the accelerator is when I really feel it. I also feel it when I turn the wheel slightly to the left, but once I get past this (maybe 5 degree turn) threshold it stops vibrating. I was thinking a wheel bearing or CV joint, but wanted to confirm.
View 3 Replies
My car was starting to over heat and I wasn't getting any heat thru the vents. Thermostat was replaced and so was the radiator cap. The coolant reservoir is still topped off, and doesn't seem to be getting sucked thru to the radiator. If I pour coolant directly into the radiator, car temp stays even, and heat eventually does come thru vents, better while driving. But, I still get steam/smoke coming from radiator cap. I cannot be buying and pouring coolant into the radiator everyday. I have a 99 Mitsubishi Eclipse with approx 140xxx miles...
View 19 Replies
there's a noise that sounds like a seagull coming from under the hood near the steering wheel. Turns out it's the vacuum brake accumulator & there was a recall on this. Unfortunately I had the part replaced back in 02, so Montero won't fix it a second time. I only use the vehicle on the weekends & didn't see any reduction in the brake performance so I put the repair off. That was over a year ago. How important is it to fix this? Other than the really odd noise there doesn't seem to be an issue.... I'm just trying to decide the future of my truck since the transfer case is gone & I can't use 4wd or AWD and more. That's been broken & flashing about a year too.. On top of that the AC is broken & now there's a light tapping noise whenever the car is in gear, but not in park.. I really love my truck but am losing hope. Everyone says it's not worth fixing. 140,000 miles.
View 19 Replies
I've had my Galant since mid-May. I bought it in a rush as a replacement vehicle after a car accident. Soon after I noticed a damp/musty smell coming from the A/C. I read that changing the cabin air filter would fix the problem, but since the Galant doesn't have a cabin air filter, I had a dealer use a foaming cleaning agent that was supposed kill off any mold that may have been present in the A/C system, the cleaner seems to have fixed the damp smell.
Right before I had this done I noticed that the floorboards on the front passenger side were consistently damp. It's been that way for about a month, and the A/C continues to leak. Now I've noticed that for the past few days when I'm trying to defog the windshield on my morning commute, the heater is blowing cold air even thought the A/C is switched off. Are these these two problems related? Also, would I be able to repair them at home?
View 6 Replies