Metro :: 1996 Geo - Ignition Fuse Keeps Blowing The Instant Key Is Turned
May 28, 2004
I have a 1996 geo metro that I have been working on for the last couple days. The problem that I have been running into is the ignition fuse keeps blowing the instant that the key is turned.
This kills the power to the fuel pump as well as the power to the ECM. (killing all the idiot lights). The engine still cranks over and all the accessories still work.
I have tried disconnecting the fuel pump wires as well as the ECM and the ignition module to try and narrow down the problem but the fuse still blows about 2 seconds after I turn the key.
View 4 Replies
Advertisement
My 96 Metro for some reason is popping the 15 amp ignition fuse randomly. First time it happened I disconnected the alternator and replaced the fuse and it got me home. Pulled the alternator and had it tested and it tested fine. Put it back in and everything worked for about a month. It popped the fuse again while driving down the road. I disconnected the alternator again but this time the fuse still blew. I disconnected the coil replaced the fuse turned on the key and the fuse did not pop. I reconnected everything and it worked fine. Hasn't repeated itself in a week. I think there is a short somewhere. Just can't find it.
View 1 Replies
I have a '96 Dodge Stratus that keeps blowing fuse #20, which is for the fuel pump and the ignition. How to isolate the problem? This happens as soon as the key is turned on. The car has 140,000 miles and runs excellent otherwise.
View 3 Replies
I have a 2004 Hyundai Sante Fe 2.4L that keeps blowing the ECU fuse under the hood when the ignition is turned on. We have replace the fuel pump and the inertia switch. I have tested the relay, ignition failure sensor, both coils and O2 sensor wiring.
View 10 Replies
Every time you engage the car in drive it blows a fuse. I have checked through the wiring but cannot see what the cause is.
View 14 Replies
I have an electrical problem with the rear brake lights on my 03 Camry. The fuse keeps blowing the instant I step on the brake. I replace it and it blows immediately. So now i can't drive it because I have no brake lights. I'm thinking there is a short somewhere, where to start my troubleshooting?
View 4 Replies
I have had this car for sum yrs never had any problem a couple months back while driving it would just shut off. Well come to find out my ign fuse would be blowing. I would replace it and it would start up and run just fine. Since then my daughter owns the car and it happened again and she replaced the fuse and it started up fine but while out of town it just shut off and now even if you replace the fuse it just blows. Just as you turn the key, it blows. So i did sum research and replaced the ignition switch. Tryed to start it and it still blows so im at my wits end. If I knew what every component that fuse ran , i could figure it out by process of elimination. I have the Chilton book but i still can't seem to find what all components that one ign fuse runs. It is a 94 grand am 3.1 v6....
View 7 Replies
Looking for a wiring diagram for a 96 model with 3.4 engine? The horn fuse keeps blowing and I don't know what else is on that circuit to check. The horn works when the fuse is replaced but the fuse blows at some time afterwards.
View 5 Replies
My 1996 Ford Ranger's Fuel Pump- Fuse keeps on blowing... (Fuel pump is new)... We need to find where the short is coming from!
View 2 Replies
I have a 06 Mercury Mariner and this past week fuse #26 keeps blowing turning the HVAC blower motor off. I replaced the blower motor since i had one already in the garage and same thing is happening. The AC will run for awhile and in about 10/15 mins the fuse will blow. Fuse #26 is the Climate control system mode switch, are these known to go bad? Is this the part I should replace or look for other problems IE compressor?
View 2 Replies
I have a 1996 Geo Metro LSI 1.3L, automatic trans.
ISSUE #1
The airbag light will not go off. I replaced the air bag control module under the shifter console and the front impact sensor near the hood latch. No effect. What is my next step? I was thinking of replacing the steering column sensor/module.
ISSUE #2
Note: I also replace the ECU to no avail. I did this because the check engine light keeps coming on. I clear the code, but "low emission threshhold) code keep returing. Does this mean my catalytic converter is gone, or could it be the O2 sensors?
View 5 Replies
Geo Metro loose head bolts... I have a 96 Metro, and for some reason the head bolts loosen by themselves, leading to over heating and planing head ... well you know.I had a farm for 20 years and took care of all equipment myself, have rebuilt numerous motors, but this geo is the first I have seen where the bolts loosen. This is the third time. I know they are tightened right , because I have the tools and experience, but not with this. Other than jb weld in the bolt holes.
View 7 Replies
I bought a 95 geo metro it ran for a few days then stop running. i have replaced about everything, new plugs, spark plug wires, sensors carborator etc. it seems like maybe it could be the timing but timing seems on. it wont turn over.
View 2 Replies
FUSE 38 Keeps blowing...it controls the fans and dealer is not sure why. Coolant fan control (FC) control Module.....
View 6 Replies
What would cause the air bag fuse to blow as soon as I turn on the ignition?
Have tried replacing the fuse and this happens (fuse blows out) each time.
95 3.8L... nearly fully rebuilt.
View 2 Replies
I have a 91 celica st and my efi fuse keeps blowing. i would like to know what the efi fuse controls, or what to check first.
View 3 Replies
2007 FJ Cruiser, 4WD, 65K Miles. I replaced the 120 AMP Fuse. Starts, everything seems to work, but the 40 AMP Fuse (ABS Motor) is blown. New fuses blow as soon as I place them in. Brakes pedal has little resistance and can barely stop the vehicle at slow speeds.
What will stop the 40 amp ABS fuse from blowing?
View 3 Replies
My 2000 Passat 1.8T is being evil again. Fuse 15 keeps blowing and I can't seem to find where the short is... however, its stuck at my work. Its a pretty big short, the fuse sparks as soon as I put the fuse near it. BIG SPARKS. Any way to start it without that fuse in?
View 1 Replies
Every time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are the aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, these lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
View 5 Replies
I have an 87 ST. Recently the turn signal fuse keeps blowing out. This only happens when I use the right turn signal. It will cycle about 5 or 6 times then the fuse blows out. Hazards are fine, left turn signal is fine, all bulbs, contacts, and wires are fine. I'm guessing it could be either the turn signal switch itself, or the relay.
View 1 Replies
My R32's Fuel Pump Fuse keeps blowing. This started after driving my car in a bad rainstorm. I think water may have gotten in the door which could be causing the short, but I am not sure. This car has two fuel pumps as it's been modified. I know for a fact the main fuel pump works as it did prime after replacing the fuse (then letting the car sit over night then opening the door). Right after the fuel pump primed though, the fuse blew. I decided to replace the fuse and start the car. The car started and ran for maybe a second or two before the fuse blew. I took a look at this thread in regards to the fuel pump not working as I thought the fuel pump was dead till today. I was wondering what are the possible problems that could be causing the fuse to blow? Could it be the relay? Could it be the switch in the door shorting? Also, where would I find the relay? I know it's under the dash, but is it under the panel on the passenger side or driver side?
View 1 Replies
