Mercury - Sable :: 2008 - Cutting Off After Valve Cover Replacement
Jan 24, 2016
I have an 2008 Mercury Sable Premiere with a 148 miles on it. Just got the Valve Cover gasket replaced and new water pump put on. The car is running very smooth as it always done,but now when coming to a stop,it either acts like it wants to cut off or sometimes it just shuts off. When it cuts off I immediately crank it back up and it starts, but why or what could be the problem? It also starts up a little slower than before and I know its not the battery because that's brand new.
View 6 Replies
Advertisement
5.4L 3v engine: The PCV is located in the drivers side valve cover. Tried to pull it out with no success and came to the conclusion that maybe it's threaded and a nut locks it in from the underside of the valve cover. Can this thing be replaced without taking off the valve cover?
View 4 Replies
So I'll be taking on a project to replace the valve cover gasket on my 2002 Camry V6. There's a bit of leakage through the gasket. And while I'm at it, I'll replace the spark plugs as well. I'm looking for a write up on this project. did a lot of searching but couldn't find anything.
View 14 Replies
How difficult is it to replace the valve cover gasket on a 2001 Santa Fe with a 2.7? Can I just do the 'front' valve cover? Are there any tutorials with plenty of pictures while doing this?
View 4 Replies
I have a 2006 Infiniti G35 base sedan. The dealer noticed oil on the engine and said that I needed to replace both valve covers and gaskets -- My question: Why is it necessary to replace the valve covers and not just the gaskets?
View 6 Replies
A few days ago I noticed some oil leaking from the left (front) valve cover area and I suspect it's the gasket. Fortunately, I didn't see any leaks from the back cover. It seemed like an easy job to replace the gasket, but as I started to disconnect the wiring, e.g., cam sensor, spark plugs, etc., I can't seem to find a way to remove the black plastic wiring harness 'housing' out of the way.
View 1 Replies
How to replace valve cover gaskets on 2002 430sc???
View 14 Replies
I did a valve cover gasket replacement. Changed all spark plugs and coilpacks. The car is still misfiring. I also just did the timing belt and water pump. Why it's still misfiring?? I'm new to this whole forum thing so bear with me lol. I'm wondering if it would be my cat, fuel pump, fuel filter. Or could it be a sensor?
View 2 Replies
A couple months ago I was hearing a hissing noise under the hood throwing the same code replaced the Valve cover, after there was no issues. Yesterday saw I had CEL and I was throwing P0174 code and there is a similar vacuum leak sound coming from under the hood but the Breather in the valve cover is not sucking in air. The Oil cap comes off but the engine starts to bog, what it could be now?
View 2 Replies
Replaced this gasket that seems to be leaking oil. Looks simple enough, is there anything i should do or know before taking on this job? It's a 2002 Accent GS 1.5L ....
View 8 Replies
I noticed the oil smell that can be associated with a leaking Cam Tensioner Adjustor Seal from my 2003 1.8T Passat a few months ago. The dealer confirmed that it was leaking and that it was covered by my extended warranty since my car was 5 years old and at 70K miles. I had the work done and after I picked up the car I noticed that the oil level was at the top of the hashes not at the top bend like it was when I took it in.
I don't know what caused it to drop to the hashes but I do know that the level has dropped to 3 visible hashes in the little over 1K that has been put on the car since then. I am concerned because in it's first 70K miles the car did not visibly lose a drop of oil.
Any logical cause for this annoying trend, the only thing that changed was that the Cam Tensioner and Valve Cover Gaskets were replaced. Is it possible something else was messed up during the repair?
View 1 Replies
In order to replace the valve cover do the spark plugs have to be taken off ?
View 12 Replies
I've got a 2004 Mazda 6 with the 3.0L V6 & a 5-speed, with about 128k miles.
The car runs fine, but was leaking oil onto the exhaust manifold and so I recently had the valve cover gaskets replaced. the mechanic could not get replacement gaskets from Mazda, and so changed the valve covers themselves also, and consequently needed to replace a couple of hoses that connect to the valve covers.
Since the repair, the car drives fine - acceleration seems normal, I don't notice any performance issues. The CEL is NOT lit.
1) When the car is in neutral, but rolling, the idle consistently bounces back and forth precisely between 1250 & 1500 rpm. This occurs always, and happens whether the gearshift is in neutral or the clutch is depressed. With the radio off I can hear the engine surging when this is going on. As soon as the car comes to a complete stop, the idle immediately drops to the a rock-steady position just below 1000 rpm, as it always has.
2) I assume related to the above, but since the repair my gas mileage has dropped from its usual 18-19mpg to 15.7-15.9mpg as recorded at two fill-ups, and my current tankful is looking to return equally low mileage.
I brought the car back to the shop and the mechanic took the car out for a drive with me, with his computer hooked up while we drove. He found nothing wrong, nothing out of whack, and saw no evidence of any air leaks.
1) Seems strange to me that the valve cover gasket couldn't be obtained, and new valve covers were needed. I want to believe the garage is being straight with me. Is this really plausible?
2) What could cause the idle to behave this way? I understand what a valve cover does (in my earlier years I changed the cylinder head on my old Saturn) and can't figure out how or why changing the valve covers would have an effect like this.
That leads me to conclude this is more likely caused by the new, slightly different hoses attached to the valve cover, but I don't know exactly what those hoses do or why they connect to the valve covers, so I'm stuck here.
View 9 Replies
Well I have a 2150 carb on my '82 truck, I looked in my parts and illustration guide and found what should be a fairly close overhaul kit for my truck based off it being a non high altitude truck and it has A/C and its a 302 with C6 transmission 2 wheel drive.
Down side is the power valve that came with my kit is a two stage power valve and I currently have a single stage power valve.
If I were to use this two stage power valve where would I buy a replacement two stage power valve cover?
Ive been looking but cant find any anywhere and I am to the point of figuring out what power valve my truck has currently so I don't have to put my only vehicle down for multiple days for a simple carb rebuild.
View 1 Replies
I have a 2002 F250 5.4with Air Conditioning. The valve covers are leaking and the gaskets need to be replaced. I am attempting the valve cover gaskets. I was able to get the drivers side cover off with some difficulty. For the passenger side valve cover. There is very little " no" room to get at the bolts. I read somewhere that I may have to drop the engine on that side. I will do that if I have to.
View 5 Replies
I recently acquired a 2003 Mercury Sable from a friend and there is a problem with the air conditioning. The car has digital controls. I select the Max AC button, turn the temperature all the way down (60) an the fan all the way up, but it only blows warm air. I can hear and see the AC compressor cycling fairly quickly. The clutch (I think) engages for about one second and it will reengage after about 5 seconds, but again, it only says engaged for about one second.
What could be the problem? I've read the AC system might not have enough pressure and needs to be recharged. Or... the orifice tube is clogged, bad AC pressure switch, or the actuator that closes the heater door might be disconnected.
How quickly should a properly functions AC compressor cycle? The car was not driven much over the past year or two as it was my friend's grandfathers. I may end up taking it to a shop but I don't want to get ripped off. How should I approach this?
View 7 Replies
Got a 2002 mercury Sable.. Always stalls out at lights.. Won't idle will stall if you don't give it gas... Also gas pedal cable broke and a spring is broke too.. What might be wrong with engine.
View 2 Replies
i have a 2001 mercury sable what im getting is its will not start but starts on occasion like today it started fine this morning did errands before work drove it turned it off short period and then started just fine and then drove to work after work it did not want to start tried every thing check engine light is not on and has not come on im am getting stumped i had to leave it in the parking lot at my work so my question is what could make it do this where it starts on occasion and then when sitting for a period of time will not start it cranks but just does not start
View 2 Replies
I have a '99 Mercury Sable with the 3.0 24 Valve DOHC V6. The car occasionally will not start. It only happens after the car has been driven and warmed up, shut off, and then an attempted restart. This problem has occurred in all sorts of temps. Sometimes it will start within 30 minutes, sometimes it takes overnight. But it will start. I have already replaced the fuel pump relay. Is the fuel pump needing to be replaced (b/c it is failing slowly), or is this problem located somewhere else?
View 12 Replies
Bought this car, drove it home, when I went to restart it nothing happened. Put in a new battery and still nothing. The starter will arc with a screwdriver but not engage. All the lights and and electrical work so I am thinking its either the neutral safety or the ignition. Is there a way to figure out which one it is with out buying both of them?
View 4 Replies
92 mercury sable 3.8so the car just started this on the 4th. it not able to turn off, switch the key to off pull it out car keeps running, been pulling the battery cable, but was told I'd hurt my alternator if kept doing it that way. just trying to fix it, so I tired switching out the ignition cylinder. that didn't fix it and also checked all my fuses they were all fine. My next idea is to change out the whole ignition switch instead of just the cylinder.
Now the second problem that i was trying to nail down before the other started was a issue with the car stalling at idle. it only happens if the car is up to temperature and it's a hot day. plus 75 Fahrenheit. just trying to go with cheapest parts and work my way up i change the air and fuel filters. then this other issue started and took priority.
View 6 Replies
