Mazda :: Check Engine Light Blinking And Idling Rough Almost Cutting Out
Jan 12, 2013
Today I went to the gas station and after I gased up and turned the car on my car started idling rough, almost to the point of cutting out. I started out on the road and my check engine light started blinking. After some time it stopped and just stayed on. The whole front end shakes pretty bad when at idle. The car has trouble accelerating till roughly 35-40 mph then seems to ride ok. I'm not very car knowledgeable, but I do take care of my car. I know I need to replace some of my hoses and spark plugs soon, but am worried that it may be more serious.
What I would like to know is: 1. What could possibly cause these issues and 2.
2003 Mazda Protege
View 2 Replies
Advertisement
The check engine light is blinking on my 98 Mazda Protege. I'd like to purchase one of those little hand held computers so that I can diagnose the problem myself. Should I leave it up to the professionals?
View 19 Replies
Our R32 has 2428 miles- and today the check engine light came on and it started to run pretty rough, babied it home and the the light was blinking when I turned into the driveway.. I know that booklet 3.2 in the owners manual is diagnosing catalytic converter issues...I have always used super unleaded, it hasn't even reached the halfway point of the first service.
View 10 Replies
Our 05 mercury monterey is riding rough and the check engine light is blinking all of a sudden. Two days back while driving home it was raining and we accidentally drove through a puddle, did not notice due to night time. After that it suddenly the light started to blink and engine felt rough. Checked the code yesterday morning and it showed cylinder 3 misfiring, no other codes came up. No one was available to check it yesterday and today. Have not started it again. Anything can be done before taking to the mechanic? I believe the number 3 cylinder is at the back side and not accessible easily. What could have happened?
View 19 Replies
Weird problem on my Passat today. First the engine light came on...followed by rough idling. It smooths out when moving, but rough again when stopped. Noticed that turning ON the AC makes it a little smoother...but when you turn off the AC, resumes the rough idle.
Already made an appt with the dealer tomorrow...but wanted to see if this problem is familiar to other owners. Either way, I will update once the dealer finishes diagnosing the problem.
The car has been perfect up to 30k miles...now 2 problems in the last month.
View 1 Replies
I drive a 1992 Mazda Protege. Recently had an oil change and put in new air filter. Recently the check engine light has been coming on. Sometimes it will run rough and sputter a bit when the light flips on and then runs normal after the light flips off, sometimes it seems to run fine when the light comes on, but the light does go off and the car runs fine after it has been running for a few minutes. Shortly before I had my air filter and oil changed I did have an incident at a stop light where the car died and did not restart for a full five minutes, at which point it sputtered for a bit and then got me home.
I took into the local mazda service center and dealer (they were the only ones who had the right kind of connector to pull the error of a car this old), and they said the only code coming up was a p69 which indicated a bad thermoswitch. I have already paid for it but the parts won't be in until Saturday. I have until then to cancel the repair and just pay restock and the original diagnostic fees. Should I go through with this repair, or do the symptoms described indicate something else?
View 2 Replies
2001 with the 3.1 6cyl. First thing that started this nightmare is I was noticing a bit of a hiccup after driving for a couple miles. We've only had the car a few months and not sure what maintenance was done so we thought maybe it needed a tune up. Before I got the parts the check engine light came on so I went to parts store to get it read, it was P0302.
Did the wires and plugs and it got worse, the code wasn't p0302 now its just p0300. But after the plugs it also started idling really rough and would be slow to shift. Once it tacked up high and wasn't speeding up. That was only once tho. Also now it has no power its like driving a 2cyl ...
Anyway we decided since the first code said 2 we replaced coil 2, no luck..ok, fuel filter and fuel injector 2, no luck. Also has cleaned various things Im not sure of the technical name for..sensors and air filters and other things.
None of this has worked the car still idles very bad and doesn't have the power it should have. Also cleaned things on fuel rail(?). He is in the process of replacing the crank sensor as someone said if it was all the way bad it would throw a different code but it may just be faulty.
View 10 Replies
I replaced the heater core in my truck this weekend. The only thing I was worried about was pulling the dash. The truck is a 1998 f150 with the 5.4.. Everything went fairy well and decided to replace the AT Shift cable as well. Got everything put back. Truck runs, no leaks, no antifreeze smell. After running about 20 minutes, it started idling a little rough and my check engine light came on.
The codes are p0136, p0156, p1131, and p1151. I know these are related to the OS sensors. My question is could it be as simple as I miss an electrical connection when putting the dash back in? Was thinking possibly somewhere on the passenger side under the kick plate or possibly something while hooking up the heater hoses? Maybe even a ground that didn't get connected back when putting the das back in?
View 1 Replies
This problem has been getting worse over the last 2 years. When the car starts it idles fine at about 1000 RPM. As soon as it warms up, it starts to idle rough, between 500 and 750 RPM. It almost quits running. As soon as you give the car some gas it runs just fine. About 3 weeks ago I got a "Engine Lean" check engine light error. I reset the system and have not gotten the error again. Since then I have: changed the MAF cleaned the EGR (made sure it closes completely and ohm out the coils in the actuator) changed the O2 meter on the exhaust manifold cleaned out the throttle body Ohmed out the air idle controller. What I should check next. I was planning to check the fuel pressure in case it is a fuel system problem. It is a 1999 ....
View 5 Replies
Mazda CX-7 sport that has rough idling when it is started and goes away when warmed up or driven. Is giving OBDII error code P0300 - multiple misfires. Where should I start looking?
View 3 Replies
Why does the check engine light come on for no reason in my 1999 mazda protege 1.6 ....
View 9 Replies
After idling for a while the check engine light has come on and stays on. I have a 2005 Mazda RX8. the car has 44000 miles on it,
View 1 Replies
I changed my plugs a few days ago on my 96' Taurus GL 3.0LI checked under my hood to check the recommended gap size and it said .42 to .46.. I went with .46. after putting them in i started the car up just fine, but later in the day i noticed when I came to a stop at a red light my car would sputter and my check engine light would start blinking. When I'd accelerate and drive it again everything would clear up and the light would stop blinking. I didn't change the wires, just the plugs in case you were wondering but I am unsure of how much that would influence my problem. Today after work i had a little trouble starting my car. After a few tries it started and my exhaust smelt rich in gasoline. Did i gap them too much? Should i get new plugs again and regap them? should i buy new wires also?Is my ignition coil going bad?
View 19 Replies
It's a 2010 vw jetta. Check engine light is blinking and the epc light is on the car is not paid off yet have no.
View 19 Replies
I have a 2008 Mazda CX-7, I take it in routinely for oil changes. somewhere between oil changes, there was an oil leak that had developed. no warning lights came on - no check engine light or oil light but the levels were low. I don't know how long it was leaking for, there was never any oil in the driveway or garage.
Any way, I took it to my dealer when diagnosed it with a dye test and told me that I needed to replace the oil filter, gasket and the entire oil cooler to properly fix the leak.
My question is for an opinion as to how urgent this repair is or if I should try and take it to a local mechanic, not my dealer. I have to say my dealer's service is less than desirable anyway. I have been checking the oil levels since I had it in on the 20th of January and it has not gone done. there are small spots on occasion on the driveway but nothing too major and I have not had to add oil to it since I had it looked at.
View 16 Replies
The problem that causes the check engine light to come on cannot be traced. The diagnosis is multi engine misfire. The dealer has checked and recheckedbut problem still exists. The last time my mechanic changed spark plugs he noticed oil on one of the plugs he removed in the rear side of the engine. He replaced the plug with the rest of them. Could it be that one or more of the spark plugs are sucking oil and causes the misfire? If so what could be the cause of that. Do I need a full tuneup? My dealer recommends replacing the cam shaft pulley because it's loose and this may or may not solve the problem. I'm not a mechanic but it appears as if the problem has something to do with the spark plugs sucking oil since the check engine light might go ou for a week or so and then come back on for a while. Lastly is it dangerous to keep driving the car especially on long trips?
View 1 Replies
Recently I brought my car for an oil change. They put the recommended full synthetic oil in and when I left the cel starting blinking and the car idling extremely rough. I brought the car immediately back (only drove ~1/4 mi.). They discovered that they put too much oil in the car. Despite their efforts of removing oil and changing filter x2, they could not get the cel to stop blinking or the car running correctly. I brought the car to the closest repair facility with diagnostic capability and they noted the car was still 1qt overfull and multiple misfire, and cam shaft actuator codes were happening. Car was towed to dealership where they diagnosed fouled plugs attributed to too much oil. Oil change facility paid towing, repair and diagnostic bills for their mistake. In the subsequent 2 weeks my car was towed two more times to dealership. Once for going into limp mode after misfires and once for fuel pump dying. Is this all a coincidence or could this be repercussions from botched oil change? Dealership says it is just coincidental.
Car is a 2007 Mercedes clk350 cabriolet.
View 15 Replies
My Girlfriend just got a 2003 Hyundai Elantra and everything was running great on it the first month she had it BUT the check engine light was on.. After about a month she called me up while driving and said that the check engine light was blinking and the car would hardly move. So I got to the car and looked at it and I noticed the oil filter was a little loose so I tightened it good this time and added a little bit of oil. It actually moved but it would hesitate. So we had it towed to a shop and they read the codes from the check engine light and told us it was leaking oil from the motor some where (not specific) and it also needed a new O2 sensor.
So I replaced the catalytic converter underneath the car and also a new sensor along with a new set of spark plugs. It ran alot better and I left it at that. Now about a week later she was coming home and noticed that when she turned left or right that the battery light and brake light on the dash came on. She drove it home and when she turned in the driveway the car went dead. It started right back up and we got it to the house and left it over night. I went out this morning and again it started right up. but when I lifted the hood I noticed the belts on the pulleys were all spinning very slowly. I'm not sure if it could be a timing chain or if it just needs new pulleys.
View 6 Replies
When I was driving to school this morning my check engine light went on and I noticed that my car is running very rough (suddenly). I also noticed that the check engine light would blink when accelerating at a stop light then go solid again when driving. I drive long distances between school and work and I think I won't be making it to work later due to this issue. This is a Saturn Ion II 2005 and gets regular maintenance on time.
View 15 Replies
So I am on my way to the store this morning and the check engine light starts blinking. After I get out of the store I try to start the car so I can drive the mile back home and then have it towed to the dealer. The car is only able to drive at like 1-3mph. I changed the cam follower 6k ago and the car only has 43k.
I'm thinking this seems like a fuel delivery/cam follower type of issue. At the moment my plan is to have AAA tow the car home so I can see if its a follower issue. If it is I think I'm going to have to take off my downpipe and put the stock one back on. When I put the car in neutral and step on the throttle I get no revs at all.
View 4 Replies
My check engine lights been on forever, like every VW, but now it's blinking fast, and the car isn't running right. It's messed up AGAIN, it's running really bad, like misfiring and not making power. It's shaky feeling in the throttle and power, almost like it's going to stall but it doesn't. What the problem is?
View 5 Replies
