Mazda :: 1989 - Voltage Buildup On Outside Of Wire Between Distributor And Ignition Coil?
May 1, 2012
My 89 Mazda B2600i conked out on me suddenly about 10 days ago. My local mechanic replaced the distributor, cap, and rotor and the ignition coil and now it's running again. But starting it up at the mechanic's, I noticed a new faint sound like a clock ticking rapidly. From under the hood it sounds more like an exposed spark plug firing, but fainter.
After driving around to make sure I wasn't imagining it, I had the mechanic take a quick listen and look. He couldn't say for sure what it was, but said it was probably nothing to worry about.Taking a look under the hood at night, I saw lights running along the spark plug wires (continuous) and flashes of light where the spark plugs insert (frequent).
If one terminal of a volt meter is placed on the outside of the wire running from the ignition coil to the distributor and the other held in the air, the voltage rapidly builds up to 4 volts (a few seconds) and then immediately drops back to zero. This happens in roughly the same time frame as the flashes of light where the spark plugs insert, but I can't tell if it's the exact same frequency. What's going on?
View 4 Replies
Advertisement
Any easy solution to reseating this wire in the connector? It got yanked out by accident when i was removing an ignition coil under the wiring harness. 2007 camry v6
View 3 Replies
Can a problem elsewhere in the system cause ignition coils to go bad? I have an '03 Mazda 6s, 147k miles, owned it since new (Dec '02). 3 1/2 ~ 4 years ago, over a period of 6 months I had to replace 4 of the 6 coils. A month ago, one of the replaced coils went bad so I had all three rear bank coils replaced (cheaper to do all three at once rather than one at at a time since half the engine needs to be disassembled to get at them). This week, I started to get the initial symptom of a coil going bad on me: Occasional stuttering in the engine.
This issue always starts when it's wet outside. The first few times it started when going through a car wash, this last time was right after Super Storm Sandy dumped a lot of rain (I am not in one of the flooded areas, NH just got a lot of rain).
View 9 Replies
My 94 Honda Accord's distributor runs with the ignition switch off. Car will not start. Does this with master relay and 50 amp ignition fuse removed.
View 9 Replies
Recently I went to a mechanic for an oil change and they told me that my "distributor was leaking externally" and I need to get it replace or the oil will corrode the sensor and heating bypass hose. They showed me the distributor and I did see dried oil/grease on the silver metal part of the the distributor. They told me it will cost $270, against my better judgment I agreed to it. When everything was done I asked for the old part back and they said no but after several minutes arguing I got my part back. I am very suspicious and I don't think that I actually need to get the ignition distributor replaced. Also they got the distributor from a Chinese company called World Power System. I would like to know if I got scam.
2000 Honda Accord LX 2.3L 90K miles...
View 16 Replies
97 SL ATX - Not firing on cylinders 3 and 6; no voltage to that coil.
I've checked:
Plugs
Wires
Coils
PTU
ECU
Timing
So I guess the CAS is the next best guess. So where exactly IS the CAS...and how do i test it? Also, where is the timing mark on the crank pulley? Cams are all aligned but I didn't see a mark for the crank and don't know where I should be looking.
View 14 Replies
I am having a problem solving a will not start issue with my vehicle. It started running a little rough when stopped, it acted as if was going to stall if it remained in gear. I had to place it in neutral to continue to run. I also noticed a backfire condition that was intermittent sometimes under acceleration. After about three days of this condition now the vehicle will not run. I have checked the fuel pressure and it is within specs.
I found there was no spark @ the spark plugs so I checked the crankshaft position sensor and observed a high value of resistance between terminals B&C therefore I installed a new one. After further checking there is no voltage at the wiring connector that supplies 12V to the coil with the ignition in the on position. I'm not sure what is the correct method in checking for this voltage is. I read that it could possibly be the ASD relay so I tried another matching relay and there was still no voltage at the coil. At this point I am somewhat at a standstill and not sure where to proceed.
View 1 Replies
My 93 camry v6 has spark jumping all over the place from the coil wire.I bought some new plug wires but only used the coil so far to see a minor improvement.I'll wait till it's dark to see where and if there is any more leakage.Plug wires are only 5mm thick.Is there something better than this(duralast) out there?
View 2 Replies
I have a 2003 Santa Fe, V4, 2.4L.
So the other day, my CEL and I got it scanned: p0320, or "Ignition/Distributor Engine Speed Input Circuit Malfunction."
It was accompanied with two symptoms:
1. The car will sometimes sputter on startup, and the tachometer will be zeroed out. I have to turn the car off and turn it back on, and it will start normally, albeit with a bit of a misfire on idle.
2. The car will sometimes die while at a stop. Just like the first symptom, if I turn the car off and turn it back on, it will work normally.
I looked on here, and it seemed like everyone solved a p0320 by replacing the Ignition Failure Sensor. So that's exactly what I did. But nothing changed; I still have the symptoms, and the CEL came back on and is still reading p0320.
What should be my next step? Could it be faulty wires that give power to the Ignition Failure Sensor?
View 3 Replies
Background: Check engine light indicated a problem with the throttle position sensor (unfortunately, don't have the exact code). The TPS on my model ('96 Dodge Intrepid 3.3L) is the non-adjustable type. There are three wires going to the TPS -- a power source, a signal wire, and a ground. The TPS acts as a potentiometer and depending on the throttle position, sends a voltage signal down the signal wire to the computer.
Here's my question/issue: After disconnecting the TPS, I tested the three wires with a multimeter. Power source (5V) and ground were fine. But I'm getting a voltage reading of about 4.35V on the signal wire. It's my understanding that with the TPS disconnected, I shouldn't be getting any voltage on that wire. Does that sound correct? If so, what would be causing me to get a voltage reading there? I'm assuming some type of problems with the wires, maybe an exposed wire on the signal wire somewhere?
View 6 Replies
I have a 2005 F250 Power stroke w/ brake controller installed. There is no voltage to the trailer brake (blue wire) pin. I've checked all of the fuses and they appear to be okay.
View 5 Replies
2007 F-150 Screw 5.4... Successful spark plug change. Well, sort of. I disconnected some of the coil clips/wires from the coils during the operation. Upon installation of the wires/clips, one of the clips did not 'click' into place.
Thinking the clip needed to be pushed/pulled, I bent the clip a bit and it snapped off! Being the slow learner that I am, a second clip also did not 'click' in place, and you know where this is going: I have two broken clips out of 8. After those two, I was much more gentle.
So, can these clips be replaced and/or spliced in? I'm thinking about just using nylon ties to hold them in place. So far, they are staying put just by being pushed in place, but these two do not seem very secure.
In the future, what is the correct way to make sure these things 'snap' back into place if they seem to not want to cooperate?
Here's a picture of the two 'press clips' that broke off....
View 12 Replies
I have a 1976 Ford F100 with a 302 and my problem is sometimes when my engine is running and I try to cut it off, it continues to run and the only way to stop it is to jerk the coil wire off. This is an intermittent problem. Happens about every 6 or 7 times I drive it. I have replaced the ignition switch and still have the same problem. Pretty sure it is some type wiring or ground issue, just need someplace to start.
View 1 Replies
I bought a 1952 F1 that is mounted on a 1978 E350 chassis.( 351W )
It has all the 78 wiring installed. When cranking engine, it will not start, unless you release key to run position. You have to get engine turning over, and then quickly release key to start. Checked back of switch, not losing voltage at ignition post while cranking...
View 5 Replies
I have a 2002 Camry 2.4L, ECM 89666-06220, ignition coil 90919-02243. One of the coils has gone out. I got a misfire code on P303. I then moved the cylinder 3 coil to cylinder 4, cleared the code and restarted the car. The new code was P304, bad coil. I found a set of low mileage used coils, 90080-19023. The dealer says this number was one of the three options for 2002. But the pin-to-pin ohm values don't match.
The 90080-19023 pin ohms, 1-2= 348, 1-3=667, 1-4= 490, 2-3= 1100, 2-4= 912, 3-4= open. The 90919-02243 pin ohms, 1-2= 390, 1-3= 673, 1-4=940, 2-3= 1154, 2-4=1403, 3-4= open. How to successfully do this substitution and not burned up ECM ?
View 1 Replies
I have a 1991 Volvo 940 SE with turbo and 162,000 miles
The problem is there is no spark coming from the ignition coil. There is power going to the ignition coil but no spark. The car turns over but doesn't start.
I have replaced the crankshaft sensor and the Ignition Module. The wire that goes from the ignition module to the Ignition Coil has been replaced with a new wire that goes directly from the module to the coil .
Also the coil has been checked and its operating within parameters.
View 16 Replies
Understanding all the needed parts when replacing ignition coils on a honda fit 2007. My understanding is it is best to replace all 4 (are there 4 total?) as well as the spark plugs - also 4?What other parts are needed, does this car require spark plug wires?
Basically, Would this be a good time to replace air filters as well? Car has 116K miles.
View 18 Replies
Found out today that my third ignition coil is bad, it's a Honda civic 03' my question is, do I have to buy a new ignition coil. I had a clerk tell me I could switch the coils and it would run fine? Is this right? could I just switch the ignition coil with another ignition coil? This doesn't sound right. Well If I do buy new one which would be the third ignition coil? is it counted from left to right or right to left? Are there any telltale signs of a bad ignition coil on sight?
View 16 Replies
Ignition coils on Hyundai Accent (2011) getting stuck in suction? Or looking for engine vacuum pathway explanation?
I previously (~6 months ago) replaced one ignition coil that had a misfire. I currently have a check engine light with "No Codes" on code reader. My engine is rough idling with very weak acceleration. This occurred when trying to accelerate up a hill. I was looking to inspect the coil resistance and noticed the replaced coil has a pretty strong suction holding it in.
View 13 Replies
2000 Honda Accord. I've been told I have a bad ignition coil. Do I need to replace all six or can I just replace the one?
View 19 Replies
On wife's 2011 ESCAPE, we want to install another "cigarette lighter" type female power port that is live only when the key is on. (to power up the GPS without having to unplug/replug it every time.)
Any best place to tap into an easily accessible wire that is hot only while vehicle is running---maybe off the power window circuit, and what color wire am I looking for & where without too much disassembly?
View 5 Replies
