2003 Chevy Malibu 3.1 temperature gauge stopped working last night, this morning having trouble starting, no check engine light fans do turn on have heat, replaced the coolant temperature sensor but gauge still not working?
View 1 RepliesI have a 2003 Malibu with 29,000 miles on it. I notice my temperature gauge reads a bit over the half way mark when driving around town. I don't notice any type of coolant leak. The gauge almost always reads above the half point, but never gets to the point of overheating. Sometimes it comes close to it but never actually overheats.
View 14 RepliesMy 1969 chevy c10 pickup that me and my dad are working on right now, we bought a new instrument cluster and installed it but the guy we bought it from installed an aftermarket temperature gauge and that gauge didn't work either so we're trying to figure out how the original one would be hooked up and how we could also hook up the gas tank to the instrument cluster so I can see how much gas I have instead of just driving it until I run out of gas.
View 2 RepliesBasically my coolant temperature gauge either reads as the hottest it can be, or the coldest. It doesn't jump around a whole bunch, but it's always all the way to one end or the other. From what I've read there seems to be a lot of different temperature sensors, so I get a little confused with all of the abbreviations, but I'm fairly certain I checked the correct one, next to the thermostat housing.
Using a multimeter I checked the resistance of the sensor, and it was around 600 ohms about 30 minutes after it had been driven. I'm not sure if this is where it should be or not, but it was rising as the truck cooled off.
Anyway, I'm not sure if I just tested the sensor incorrectly or if there could be another issue. A friend of mine suggested that the thermostat may have gotten stuck or something, but it doesn't seem like the gauge would switch at all if that were the case. What I should check to try and fix this.
I have a 2003 Chevy Malibu LS. Occasionally, my theft system light will come on when I start my car. I usually have to wait 10 minutes until it deactivates. I don't understand why it does this!
image.jpeg2448x3264 1.3 MB
My 2001 Malibu v-6 temp gauge is not working. I have replaced the temp sending unit and it works for a few weeks unit it goes out. What keeps killing the temp sendor?
View 6 RepliesI have a 2009 Prius. Last summer I noticed that the outside temperature gauge was not working properly. I asked at the wonderful dealership I go to and no one knew anything.
View 10 RepliesI have a 2003 Chevy Malibu, V6, 3.1, auto, 140k miles. Car started out with code 0420 with no noticeable symptoms, but then added code 0303 (miss fire cyl #3) with loud knock (mostly after warmup) and loss of power under load. Now internal loss of coolant (no puddles or external drips). Changed plugs and wires - no change - all plugs looked good with no sign of contamination. Questions - if this is a valve/piston/lifter problem (which would explain the knock, miss-fire and loss of power), why would I get the loss in coolant? If the loss of coolant is fouling plug #3 (which would explain the coolant loss, miss fire and loss of power), could that give me the loud knocking? I don't see how a valve/piston/lifter issue would cause a leak in coolant but I also don't see how a coolant leak into cyl #3 would give me such a loud knock. Do I have two different problems? If it is a leak into cyl #3, is there any way to tell if it is the intake manifold gasket (which leaked before and was replaced five-six years ago and which I could do again if I had to) or a blown head gasket (which I don't think I could fix or afford to get fixed)? Engine will occasionally get hot (but not overheat).
View 7 RepliesThe outside temperature gauge and park distance system on my Phaeton isn't working. In place of the temperature reading on the dash it just says --.-C I've had it scanned at my local Bosch diagnostic garage and it showed a fault on all six front parking sensors. I can't recall whether he mentioned the temperature sensor as well but I put a new one on anyway as they are cheap and easy to get at. It made no difference. They were very busy so didn't have an opportunity to do any further investigation or dis-assembly and I was in no rush so am taking it back next week.
I have checked the two block connectors which the wires from the parking sensors and temperature sensors go in to and that seems properly connected. Is there another connector somewhere or is there a fuse that protects these somewhere as there isn't a fuse described in the manual as being related to these?
My sister drives a 2005 Nissan Altima. I am not real familiar with Japanese OEMs but I do most of my own repair work on my car (which currently has issues of its own). What's wrong and how do I go about making the repair...
View 8 RepliesI borrowed a friend's small Toyota truck for a few days of easy chores, and made a point to check the fuel at the beginning: the gauge showed 3/4 full. Four days and only 25 miles later, when I got in to return it, I noticed the fuel gauge was not working, I'm certain there's no fuel leak, I would have noticed that: the truck had been parked on my property the entire time, driven only a few hundred feet from one spot to another moving firewood around, so I would have smelled the gas if there was a leak.
When I added a couple gallons of fuel, the gauge didn't budge. Once on the road, I realized that the engine temperature gauge was also dead - no change on the gauge after 10 miles. So I have two non-functioning gauges which failed on my watch. This may not be directly my fault, but as my friend is kind enough to lend the truck whenever I need it, my contribution is to provide maintenance.
Is there anything in common between the two gauges which would explain the synchronized failure? Or is this total coincidence? This one is outside my experience, so don't know where to start. It's a 4 cylinder, 5 speed manual, base model truck, about 150k, generally runs just fine. There are no other gauges, and I don't recall what warning lights there might be, but I didn't see any after I realized there was a problem. Would the whole instrument cluster die at once, or could this be something like a bad ground for the cluster? I don't mind investing effort into tracking down and solving a problem, but if it needs a new cluster, that will cost more than I'd like to contribute, yet the problem occurred while I was using the truck (gently). My total use of this truck for all the times I've borrowed it is certainly less than 300 miles, so I'm reluctant to fund the entire repair if this is something that just comes with age.
I have a 2004 Pontiac Montana with about 107500 kms on it (VIN: 1GMDX03E24D183870) and the coolant temperature gauge is not working properly. Sometimes when I start my van, the temp gauge is pinned at MAX temp and stays there the whole trip...other times it's pinned at MIN temp...and other times it seems to work OK.
When it's pinned at MAX temp, I check the actual temp that the on-board computer is seeing, by using my OBDII scan tool...and I get about 87 degrees C when I'm halfway into my trip (i.e. - when the van is at operating temp), which seems OK. All the other analog gauges are working perfectly.
I read a lot about the issues with "connector C305" on the Internet on the Montana vans...could this be the problem?
Having a problem with my temperature gauge inside the truck. No matter how far or long I drive, the needle barely moves off of cold. Would the thermostat be the likely suspect? If not, what else could it be? There is no "check engine" light on and my ODB2 reader reads a temp of around 70c solid. If it is the thermostat, where is this part located in the car and would I need to replace JUST the thermostat or are there gaskets/housing-type things involved as well.
View 7 RepliesI have a 2005 mk4 gli and the other morning I went out to start my car for work and all I got was crank no start. I then realized my fuel pump wasn't priming when I opened the driver door. After work I came back and checked the fuel pump fuse and swapped the relay with another I had, still nothing. A buddy of mine decided to check the connector at the fuel pump for power, using a power probe I believe he hit all or the majority of the wires with 12v of negative and/or positive power. He then unplugged the connecter and plugged it back in and the car fired right up. But I noticed that my fuel gauge, engine temp gauge, and outside air temp readout were all not functioning. I've searched and searched without being able to narrow down a solution.
View 19 RepliesI have a 1992 Aerostar 3.0L end my temperature gauge on the dash doesn't move at all. Stays all the way to the left. I read on other forums that to make sure the gauge and the wiring are ok, i need to connect the wire that goes to the sensor unit to the negative of the battery. Gauge should go all the way to hot when the ignition switch is put to on position. That was exactly my results. So, i replaced the temp sensor unit but still gauge doesn't move. I didn't use any sealant on the threads when i installed the sensor. Connector looks ok. The engine warms up fine. I really don't know what else to think or do.
View 11 RepliesTemperature gauge quit working after changing the thermostat and coolant.
With the engine off, I disconnected the single wire from the temperature sending unit and switched on the ignition without starting engine. The gauge pointer stayed in at the Cold mark. Using a Jumper wire, I grounded the sending unit wire and the needle on the gauge went to the Hot mark.
I quickly turned off the ignition, and replaced the sending unit with a SW-2328 (F1SZ-10884-A) Temp Sender. Warmed up the engine, but still no reading on the dash gauge.
2002 ford sport trac.I have been having an ongoing issue that started with the engine cranking but would not turn over until an hour passed. After replacing multiple parts (cam shaft sensor, crankshaft sensor, ignition pack) I am now down to poor fuel economy as the last of the issues (roughly 12 in the city and 15 highway). I was told the issue may be the engine coolant temperature sensor going bad so I decided to replace it. I found this was very difficult due to it being a plug and locking pin design and in a very tight spot in the engine.
I tried to purchase a replacement and the parts store kept trying to insist on selling me a part with threading. I finally found someone that figured out the issue and found the part for the 2001 sport trac had the same plug style with clip that did fit but was shaped a little different on the sensor end which I assume was due to being aftermarket. I noticed that there were two plugs side by side and the one easiest to access was on the left and I was told the one on the right was the sensor that gave the temperature reading to the gauge.
After installing the engine coolant temperature sensor I found the temperature gauge on the dash now will not respond and is sitting below the cold end of the gauge completely off. Is it possible this is because the part was for a 2001? Is the sensor on the left (passenger side) the engine coolant sensor?I would hate to put the old sensor back in just to test if that's the issue due how difficult it was to put that locking pin back on. What to check that could resolve the gauge issue before pulling this sensor back out?
So my Malibu overheated for the first time, and note it just won't start up..
View 16 RepliesLong story: I have a 2005 Chevy Malibu base. About more than a month ago I was driving home from work my car stalled about 3 times. I was able to finally get home I checked the oil and to my shock there was none. I quickly put some in and my car started just fine didn't stall again. I drove it the next day nothing. Then the day after that I drove it to Walmart on the way back it stalled like 7 times and after that last time it wouldn't turn on. I got it towed to a shop where my car remained for over a month. The crank position sensor was replaced, the battery, and the ignition switch. I was told it was fixed, picked it up drove it to a town 30 minutes away it was fine, then drove it back it started stalling every 5 minutes.
Managed to take it back to the shop, they couldn't figure out why it was shutting off so they got a second opinion at a Chevy dealership nearby and they replaced the ignition control module. I picked up my car drove it around for awhile and the check engine light came on I was near pepboys they checked the code which said I needed to get the catalytic converter check/replaced. So I drove my car home. Next day drove it all day it stayed on, thought my problem was solved. Then that evening turned it on and within a few minutes the engine shut off and now it won't start at all. The mechanics that I took it to obviously don't know what the issue is nor do the mechanics at Chevy. It is not the fuel pump that's one things that can be crossed out. Or is my car done and should be junked?
i have a 2005 chevy malibu classic. a few months ago it started sputtering when we would try to crank it and would take several tries before it would run, then it stopped. So far we have replaced the fuel filter, fuel pump, fuel pressure regulator, idle air control valve and crankshaft sensor, and it still wont stay running when you try to give it the gas, it dies....
View 4 RepliesI have a 2011 Chevy Malibu, with a little over 100k miles on it. A couple weeks ago it started acting a little funny when I would shift into reverse after starting it after sitting for a while. I thought it might have been due to temperature as it didn't do it after the car had warmed up or when it was warmer out.
Yesterday it started acting up really bad, will not shift out of first gear, and will not shift into reverse, and the check engine light came on. I was able to get it up to O'Reilly's to get the codes. It came back with 2 separate codes.
P0700 - Transmission Control Module (TCM) Requested MIL IlluminationP0776 - Clutch Pressure Control (PC) Solenoid - Stuck Off
The guy there seemed to think that the second code was probably caused by the first one, and most likely the TCM needs replaced. It makes sense to me, but before I head down this path I want to get some input, as it is a little over $300 for the part.