Lumina :: 1996 - How To Clear CEL Code


Nov 8, 2013

Is there a way to clear the " check engine light" code if I dont have a instrument? Can I disconnect the battery and will that do it?

View 2 Replies

Advertisement

Chevrolet - Lumina :: 1996 - DTC Code P0101 - Mass Airflow Sensor Malfunction

So I have a 1996 Chevy Lumina (3.1L V6 engine) and I keep getting a DTC code P0101, which is a Mass Airflow Sensor malfunction. It's rather annoying because every time this happens, my engine shuts off. I'm talking no power steering, no power breaks, no acceleration, nothing. So I replaced the mass airflow sensor and it continues to stop about every five minutes. However, it does something odd and that is that the car drives just fine when it's in Overdrive and stops when it's in regular drive. I don't know if that's important, but I thought it might diagnose the problem.

View 4 Replies

Lumina :: 1996 LS Intermittently Start With The Key

Because my car would intermittently start with the key (it would run fine if I jumped the relay at the starter) I just put in a new Autozone lock/cylinder in my old '96 Lumina LS. Prior to the install, I took the new lock/key and old key to the locksmith, who told me he has the tool to read the resistance on the key which corresponds to the computer in my car and I wouldn't need to go to GM. Also, the brake lights weren't working right so while I had the steering wheel off I replaced the turn signal switch too.

I went to check to make sure the turn signals/brake lights worked before buttoning everything back up so I reattached the battery, with the key in the new lock; the dash lights came on, the chime went off as they should. I then put the ignition key in the 'run' position and the chime died and the lock mechanism will no longer turn and I get no lights at the dash. The car won't shift and I'm effectively screwed! FYI - The headlights and brake lights both now work but I can't turn the key in the ignition. Did I just get locked out? Did my locksmith hand me a line of bull?

View 5 Replies

Lumina :: 1996 / 3.1 - Turn Key Wait 2 Minutes For Fuel Pump Then Start?

I have a 1996 Lumina 3.1. For the last few years, every now and then I would turn on the key, all electrical systems, lights, windows, radio, etc. would work but it wouldn't turn over. If I waited about 4 minutes it would start perfectly and it wouldn't happen again for up to a month. Last week it did it and after I waited and tried it again it turned over once then everything went dead. A mechanic (friend) installed a new battery and it started. He took it to his shop and installed a new computer. Everything read fine, but now when you turn on the key it will turn over fine but not start. Leave the key on and wait about 2 minutes till you hear the fuel pump start and the engine will start fine. If you stop for a few minutes it will start but if you stop for more than 5 or 10 minutes you have to wait for the fuel pump to come on again.

View 7 Replies

Chevrolet - Lumina :: 1996 - Compressor Clutch Does Not Engage And Fans Do Not Spin When AC Turned On

I am having trouble with my air conditioning system in my 1996 Chevy Lumina. When I turn on the AC, the compressor clutch does not engage and the fans do not spin. I was able to jump the compressor so the clutch engaged, however, the fans still did not spin and the AC was not cold. I then jumped the low pressure cycling switch (near the accumulator), which caused the fans to spin while the compressor was running. However, this still did not produce cold air from the AC and none of the AC lines were cold to the touch. I am starting to think the system is low on Freon, but I do not have gauges to test the pressure.

View 2 Replies

Golf IV / Jetta IV :: 2005 - ABS Light Is On - Can't Clear The Code

I have an 05 GLI with many mods, far from stock. In the past i have tried to recode the ABS module with my vag com to ABS only because the traction control does not work when you make 300whp and im sick of pushing the button every time i get in the car. The module will not take the recode so i gave up. Then about a week ago the ABS light came on for no reason and i can not turn off the traction control with the esp button so i checked the code.

It said something about a system test (ill have to check it tomorrow to find out what the code was) i tried to clear it and it would come right back with no other codes. Then i took the car out and beat on it and the traction control still works (or trys to) and i hammered on the brakes and the ABS still works and the fluid is still full. Then i came to red light and i after i stopped i pushed the brake petal hard and the traction control light started flashing (im still stopped and not moving at all) It just kept flashing for over a minute even after i started driving. Then the tc light stayed on and the ABS light went off. As soon as i turned the car off and back on it was ABS light on and tc light off. Still only the same code stored. I tried recoding it to a car with ABS, ESP, and HD suspension and it took that coding. But still had the same code so i recoded it back to my oem one.

View 24 Replies

Santa FE SM (2001-06) :: Code B1382 - Airbag Light Came On And Will Not Clear

2003 Santa Fe GLS 120K mi. 2wd, 2.7L, AT.

Been having for some time an intermittent problem where the air bag light will come on and not clear. I can clear it sometimes by removing the neg. batt. term. and letting it sit for a few minutes. The "air bag" light always seems to come on when someone sits in the passenger seat. The dealer reported a trouble code of "B1382-- PSAB harness improper pin tension" They said that they re-seated a connector and it was good to go. Now the "air bag" light is on again. Does the description refer to the pin tension in a connector? which connector does it refer to and can I just tighten up the female part of the connector such that the male pin makes better contact? Is it the yellow connector under the seat?

View 7 Replies

Ford Ranger / B-Series :: Code P1403 Keeps Coming On After Clear It

My 96 4x2 2.3ltr is throwing this code (P1443). I clear it and it comes back a few cycles later. I will fix it next but won't be able to get to it for a couple weeks. What if any affect does this code have on fuel mileage and or engine performance/power?

View 3 Replies

Lumina :: Cannot Get The Car To Start - P0108 Code

My car turns very rough and then turns off as soon as I let go of the key... won't hold an idle...

Checked the MAP sensor and when I tried to pull it from the hose the tube was very brittle and broke...

I put in a new MAP Sensor and checked for bad hoses... Still can't get the car to start!

View 1 Replies

Lumina :: 1996 - When Turn The Key Starter Engages But Engine Will Not Turn Over

I was driving to work and lost all power (during rush hour) I was able to coast to a exit. Had it towed home, when I turn the key the starter engages but nothing after that, the engine will not turn over. I checked the battery and has a full 12 volts.

I removed the belt and front plugs to see if I could manually turn the engine over but it will not budge. How can I tell if this engine is really locked up or if maybe something else is happening?

3.1 V6 engine .....

View 7 Replies

Caravan/Voyager :: 2001 - Is There A Reset Function To Clear Code Disconnecting Battery

I bought some long beams at the local lumber yard. So drove home with the rear cargo door open. The ABS light went on brakes were pulsing mildly and making an odd sound. I cant see why the rear cargo door would have any connection with the ABS system so I assume that's a coincidence.I took the van to the local car store they scanned the code. It scanned code 4 indicating the passenger front sensor. I replaced the sensor but the ABS light is still on. Is there a reset function to clear the code disconnecting the battery didn't work? Or am I looking at another component failure?

View 2 Replies

Ford 6.7L Power Stroke Diesel :: 2011 F250 - P1635 Code Won't Clear

Bought a 2011 F250 with P1635 code. It has 35x12.50 tires my Sct x4 tuner only goes up to 34 inch tires. Im new to the 6.7 diesel game previously had 6.0 and want to hear from yall what to do.

View 1 Replies

Lumina :: Code P0240 - Check Engine Light Comes On

So the only thing I have changed is the fuel pressure regulator. Man after I did that my cars been running super, even has some added pick me up on acceleration!

So today my check engine light comes on and I get this code???? P0240...

View 7 Replies

Lumina :: 98 3.1 24x - Code 336 Indicating Crankshaft Positioning Sensor Out Of Limits

recently started getting a 336 code indicating crankshaft positioning sensor out of limits.

removed the 7x sensor but it seems ok and the car does start ok. checked the ECM input of the 24x sensor and I never get anything but straight 11.2 volts when crank turns. checked at the 24x connector and get the same. (green lead on B connection).

problem I have is getting to the sensor. The crank pulley bolt just will not let go! I've tried impact gun set to max,(typical DIY type gun, not the best) and tried a breaker bar with hammer. how to get the crankshaft balancer off.

View 6 Replies

Taurus :: 1996 GT Misfire - Code PO305

Have a code PO305. Replaced coil. Plugs and wires. Checked front injectors. They make that correct clicking noise when listened to with a long screwdriver touching their bases. Attempted to listen to rear injectors. Only could touch outer two and they make more of a swishing noise. CEL will blink after driving higher speeds but will return to steady on when engine is turned off and rested for a few minutes. Does have new fuel filter. Newer pump. Newer Cat. CEL came on when driving at highway speed with cruise control on. Engine is a 3.0 not flex.

View 14 Replies

Pontiac - Bonneville :: 1996 - Oil In Antifreeze With PO300 Code?

How serious or expensive is cost of repair for problem causing oil in antifreeze for 1996 Bonneville with PO300 code?

View 5 Replies

Chevrolet - Express :: 1996 - Code P0305 - Misfire In 5?

96 Chevy express 1500 V8-305. Have a P0305 code...Misfire on 5. Let me tell you everything I have done so nobody wastes their time.

I have, replaced the entire ignition system, "EVERYTHING" including a new distributor...Not the problem... I did a compression test...Not the problem...injector cleaning...not the problem.

When I moved the wire harness that goes into the "spyder" fuel injector system the engine smoothed out. I untaped the harness from around the plug and applied pressure to each wire the engine smoothed out. The back row 2nd pink wire seems to cause the most reaction.

My question is...Is it the wire harness or is it the injector system not reading plug? or could it be a combination of the 2? If I replace the wire harness might I still have to replace the injector system?

View 1 Replies

Toyota - 4runner :: 1996 - Getting Catalytic Converter 420 Code?

1996 4runner here (187,500miles), with weld in after market cat (on when purchased, with less than 1000 mile on it). started throwing the 420 code beginning of last summer. Replaced both O2 sensors and same results. Was coming on after every 30-40 miles after resetting, replaced wires, plugs, cleaned throttle body started coming on ever 120 miles or so. Now in the middle of winter it has gone 450 miles and still has not come back on?? Does the winter fuel blends in Georgia, or cold more dense air make a difference on cat performance? Still plan to replace it with a direct fit with a warranty but curious if I am overlooking something.

View 6 Replies

Ford Wiring/Electrical :: 1996 - Got Code P1351 - ICM For EEC-V 460?

I have been trying to resolve the last of my codes on my MAF conversion on a 460. I am using an EEC-V box and had two codes I couldn't get rid of. I solved one yesterday, P0443 a evap purge code, by running the circuit directly from the EEC to the VMV.

The current issue is a code P1351, which is the IDM circuit. When I put everything together originally, I assumed that all the later systems used the black CCD module, Motorcraft DY-533. Adam Maurer asked that I check this to be sure. When I went to the Motorcraft website, I found that all 460 remote modules are listed as a DY-1075, gray push start.

The wiring diagram (from the 1995 and 1996 EVTMs) shows a yellow with black stripe wire (circuit 382) from pin 3 of the ICM to either pin #4 (EEC-IV) or pin #48 (EEC-V). Older systems show to start (circuit 32, red with light blue) to pin #3 of the ICM and a suppression resistor from circuit 11 (coil -) to pin #4 of the EEC-IV. which ICM a 1996 EEC-V 460 should have?

View 1 Replies

Ford Aerostar :: 1996 - Airbag Light Comes On - Code 41 Flashing

Got an air bag code 41. Comes on and flashes the code a number of times, then goes off for the rest of the ride. It is a 96 Arerostar, XLT, 4LV6. From what I read it is a short someplace. Where are the crash sensors and how do you check them for "shorts"? I don't understand much about the whole system.

View 12 Replies

Ford - Explorer :: 1996 - Airbag Error Code B1944

I just pulled error code B1944 from my 96 Explorer. It says

Crash sensor ground
Ckt 1, High res/open

I found the airbag diagnostic module (in passenger cowl area) and checked for loosed wire, nothing found. Where the loose ground wire is located? I checked under the seat (didn't do a through job, but looked).

View 1 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved