Lumina :: 1990 Chevy Just Stopped Running While Driving At About 55 Mph
Aug 6, 2014
So about 3 weeks ago, I was driving down the road at about 55 mph, on cruise control, when my car just started slowing down. I looked to see all of my dashboards lights on and I realized my car was not running. I shifted into neutral and the car started right up again, but when I pushed on the gas it just kind of stuttered and shuttered before dying again. When I came to a stop, again the car started right up, but repeated the shuttering and hesitating when I pushed on the gas and tried to get going again.
So, I repeated, but this time i just pushed very gently on the gas, getting up to between 5-10 mph before the car died again. At this point, it just stopped running completely. The engine would turn over, but would not keep running. When I got it into the shop, the mechanic said they put a fuel pressure gauge on there and the readings indicated that there was plenty of pressure, no problems the fuel pump or lines.
After further research, the mechanic said he thought it was an electrical problem, that it could be the crankshaft sensor or the ignition switch module, but he just did not really know for sure. I had him replace the crankshaft sensor, since it was the cheaper part, and it didn't fix the problem. So now I am just kind of stuck on what to do here.
View 4 Replies
Advertisement
Last winter, my car sporadically stopped while I was driving slowly or while I was standing still. I usually turned the engine off and restarted it right away without a problem. It happened a few times and then it stopped. This winter, it began again - frequently. I realize now that it only happens during the cold months.
View 10 Replies
I have a 1990 3.1L, multiport fuel injection (NOT sequential FI), which runs very well most of the time. However, when I cold start it runs rough (misfire) for about 1 minute (no throttle) or until acclerated. The is no misfire when running normal, but it might be running a little rough when stopped at a traffic light (in Drive, foot on brake).
I put new plugs and wires on, but it did not affect this problem.
I am not using coolant, or oil, the plugs that were removed were somewhat worn, enough that I expected to notice a difference after they were changed.
I have not yet (1) cleaned the MAF, (2) checked carefully for vacuum leaks, (3) checked for leaking injectors.
Since this is a 1990, OBDI, I can't say which cylinder is misfiring or how the fuel trims look etc.
View 10 Replies
1990 GMC with 4.3, 6 cylinder. He saw no spark so after checking on prices for things like rotor, cap, module, he just bought a rebuilt distributor. Installed it and it still will not start. If we run the coil wire to a plug, we get a spark. Check an individual plug, no spark. Yes, the rotor is installed ! I would think module, but rebuilt distributor came with one. Crank position sensor? I don't see one. Does a 90 year have one? How bout ECM? When it stopped working, he was driving it and it spit and sputtered and stopped. And, just in case....where is the ECM on this truck?
View 4 Replies
I have a 1999 chevy s10 2.2 L that just shut down while driving, I have replaced crank shaft sensor, ecm, ignition control module, coil packs and still having issues, she will start now but won't stay running, what else it could be, it has been down for almost 5 months.
View 1 Replies
I have a 1999 chevy lumina 3.1 with only 317,000 mi. and running strong. I had put new plugs,and wires about 6 weeks ago. The other day it started misfiring and I could smell the gasoline. I checked the tail pipe and it showed black smoke. In addition I put a piece of paper on the tail pipe and I could feel the misfiring with a consistent rhythm. I notice that it is running flooded(like if a fuel injector is not working correctly.) I cleaned the throttle body, checked all the coils and the spark plugs and they are good. It does not show any check engine light on. What could it be?
View 6 Replies
Was called today to look at a car that wont start its a 92 Chevy lumina euro with the 3.1 v6 automatic 4 door. The car has a new crank sensor recently installed ran well for a while and now has no injector pulse. Checked for spark its good. sprayed starting fluid in the intake and it fired for a second acted like it wanted to run and then died. Checked for fuel at Schroeder valve it has fuel there I don't have a fuel pressure gauge but it sprayed pretty good. I'm not real good with electrical but thought maybe the ICM under the coil packs could be bad I have one off a running engine on my shelf but wanted to see what other people had to say first.
View 4 Replies
A week ago, driving home, the tech started to drop quickly to zero then recover, like the ignition was turned off and then back on. I was able to make it home. The car was due a tune up. I replaced the crank position sensor (OEM), replaced sparkplugs (Autolite Iridium), air filter, fuel filter, no luck. I ohmed the coil packs, secondary resistance showed good, replaced the ignition control module (aftermarket). After this, engine would stall after it was at temp, could restart, once put in gear it would stall, but I could go in reverse and drive home backwards.
Reinstalled original OEM ignition control module. Towed to GM Dealership, mechanic said fuel pump was bad, ignition wires needed replaced, one injector ohmed bad. I took car home, replaced fuel pump (OEM), ignition wires (OEM), no luck. Removed plenum, found pcv valve clogged, and hose kinked, replaced both, ohmed all 6 injectors, 5 injectors read 12.3 ohms, 1 injector was 11.6. Replaced all 6 injectors, (Napa), plenum gasket, still same problem.
GM dealership said computer said no data, they though perhaps ignition control module was bad, but I don't think so. I hooked up my Actron shorting plug, reads code 12 which means no faults, no other codes. I noticed EGR valve has a lot of carbon in the hole, thought about changing it, but I'm really not sure where to go now. The car is a 1994 Chevy Lumina with 230,000 miles, spent about $500 the last week doing brakes, and trying to fix this engine. Where to go from here.
View 5 Replies
This car started to stall sputter. I replaced the ignition module and it worked for while then nothing at all but still cranks. I checked all of the fuses and every thing was working. What I have found and i think this was the whole problem. The wiring harness that goes from the ignition module to the crank sensor, the wires were twisted and frayed and most likely grounding out on the frame and making the computer to shut down. So far after replacing the wires it started right up. Have not had a chance to take it for a test run to re learn the computer because my brake line busted.
View 1 Replies
My brother's 1995 chevy lumina 3.1 engine has been dying while braking for a stop and while reversing. Has replaced fuel filter, map sensor, throttle sensor, o2 sensors and still no change. He says he doesn't believe a tune-up is the cause either.
View 8 Replies
I have a 99 Chevy Lumina. The car periodically flashes the low coolant light. I check it and its fine. I don't know if its related to my recent problem. A couple of days ago, my car wouldn't start. All the lights and stuff come on, but there is no clicking or even trying to start. I kept trying. It wouldn't work. I left it alone to make some phone calls. I messed with it again after a little while and it started. It has been running until today. It started, I got my son to daycare. Then when I tried to start the car to leave, it did the same thing again. I let it sit for a couple of minutes and it started again.
View 13 Replies
My 90 lumina euro 3.1 has idle surge after it warms up. fluctuates between 600 and 1200 rpm when in drive. When you first get on the throttle it wants to die. Once you get past that it runs smooth while driving. Ive also notice that it tries to "buck" when its at lower rpm and barely on the throttle while pulling.
I can't seem to find any vacuum leaks, has recient tuneup, had a egr code and that has been replaced. I've cleaned the throttle body also. Previous owner had intake gaskets replaced as well as fuel injectors, fuel rail, fuel pump.
View 12 Replies
I have a 1990 chevy lumina 2.5 L 4 cyl. 100,000 miles....The car recently started chugging while in drive and will not accelerate correctly, when I do get it to 55 mph there's still chugging, Ive replaced the fuel filter, spark plug and wires, fuel system clean, new battery, there is a inch crack in the exhaust manifold on the front of the engine, not sure if that would make me lose power to accelerate, the car idles fine, but chugs when put in drive, and will occasionally die when put in reverse....
View 3 Replies
1995 Chevy Lumina 3.1L Sedan with ~182K mi
Over the past 6 months, I have noticed fuel odor just about any time I turn off the vehicle, and I am also experiencing progressively higher levels of fuel tank pressure each time I remove the fuel cap. The fuel tank pressure seems to be greater the lower the level of fuel in the tank whenever I remove the cap. 6 months ago (~Sept) it was only a slight "hissing" periodically when removing the cap to fuel up, but now it occurs at every fill up and seems to have enough pressure to push the cap entirely off had I not been careful to slowly loosen the cap to relieve the pressure.
The entire fuel pump and sending unit assembly in addition to the tank and filter were all replaced about 4 years ago in May 2010 or about 28K mi ago. The issue has just come up progressively over the last 6 months.
Today, I inspected the evap. emission components and lines from the tank to the canister to the purge solenoid mounted on the rear of the engine. All lines are connected and seem to be in operable condition. The line from the canister to the purge valve mounted on the engine is completely free with no obstructions. I blew out the line with compressed air and absolutely no exiting particulates were observed. The lines on the bottom of the canister did not show any signs of wet fuel and there were no carbon particles present in the lines from what I could tell from disconnecting and inspecting. The vapor line from the tank to the carbon canister is not kinked or pinched in any manner.
I believe there is a fuel vapor check valve that resides inside the tank connected to the fuel pump assembly/sending unit. This was all replaced as a single unit as mentioned above. I am thinking this check valve may not be functioning properly and not allowing the vapor to escape into the carbon canister. I tried to apply slight pressure and vacuum on the vapor line connected to the check valve on the tank but no air was able to move in or out even with the gas cap off. However, I do have a full tank of gas right now, so I imagine the check valve will be closed.
The check engine light is not on but since this is an OBDI vehicle I am not sure there are any evap. emission codes anyway.
How can I test the gas tank vapor check valve? How can I test the vapor purge solenoid located on the rear of the engine? What malfunctioning component could be causing the excessive fuel tank pressure.
View 9 Replies
I installed a new motor in a 1990 chevy Silverado about 5 months ago. every time i start it there is a loud clunky noise which goes away after about 1 or 2 minutes.I took apart the exhaust.. why does #2 cylinder have rust on the exhaust port not black soot?
View 1 Replies
I have an 06 Lexus GS300 awd. Yesterday, when I left out of my neighborhood, my car drove approx 1 mile and just STOPPED running. I coasted to the shoulder of the road & attempted to start it again. It cranked & started for about 2 secs & died again. After that, each time i tried to crank, it would try & try to start (starter sounded strong) yet would never "turn over". I could feel/hear a few rough spitting & sputtering type feelings/sounds trying to start it, but ultimately it wouldnt crank.
I called a friend (another single mom) to come get me & i purchased some starter fluid & went back to try it. We hooked it up to her battery as I had run mine low trying to crank it. After it had been sitting there while we went to the store, it again tried to crank when I attempted to start ot, but died again within a sec or 2. Then, wouldnt fully crank again. I hear my alternator clicking & as i said earlier, the starter sounds very strong & normal when i push the ignition button.
I tried to just turn it to the "on" position (2 button pushes), leave it a few secs, turn off, then try to crank again (hoping to "prime" the gas lines in case it somehow had sucked in any air or water....which it kinda "feels" like) Still after all that....nothing. I tried having my friend crank while i sprayed starter fluid into the intake, and it actually cranked and would stay running as long as i was continually spraying the fluid. The sec i stopped, it stopped. I really dont hear the fuel pump turning on, although admittedly I guess I never have paid attention before this to know if I ever could "hear" it previously. Im wondering if its just a very quiet one, or if its not turning on at all? (I understand it's in the back of the car kind of under the backseat & not under the hood).
View 11 Replies
I have a 2002 monte carlo, driving on the road it stopped running, wouldn't start, when i got it home it started but missing bad, I replaced the plugs and coils, didn't stop, tho one seemed to make it a little better, strangely I have noticed the power brakes don't work anymore, very stiff like standard, so may be connected as happened at the same time, searched for a vacuum line off, don't see one......
View 2 Replies
1090 Lumina Sedan 3.1 ... First time it had starting issues Recently. About 2 months ago my lumina's engine would die when i pushed down on the gas pedal. After 2 days of trying to fix the issue it wouldn't start at all, i replaced:
TPS
MAP/MAT Sensor
Fuel Filter
None of these worked so i sent it to a shop, they replaced:
ECM
Multi Port Injection (All 6 Injectors)
TPS (even though i had just installed a new one)
Serpentine Belt (it broke when they were test driving it after the Repairs were done)
The car would not start even after they replaced the first 3 parts on the list, so the tech looked further at the engine and found frayed and open wires, on the bottom near the front side passenger door, he repaired these wires and the car started and ran.
The only issues i had after their repair was a rough idle while braking and/or when i was at a full stop, the rough idle went away after a few days of driving.
((Current No Start Issues))A week ago i had what i am guessing is a few electrical issues: Speedometer Twitching and then dropping to nothing while driving, temp and oil light popping on and then off, when the engine was at a good temp and the oil was fine when i had checked the day before.
I went out a few days ago to run some errands and on my way home i turned a corner and when i put my foot down on the gas pedal the car just went "Put-put Put-put" every time i pushed the pedal more than a 1/4 of the way down. i reach a stop sign and being i was in the middle of nowhere and no one was coming down the road for miles i braked slightly and went past the stop sign halfway through my turn the engine died and i coasted to the side of the road, i got out and checked the engine, i had coolant not a whole lot but enough, then i checked the oil and it as far as i could tell it was at the add line even though it had been fine a few days before,(there has been no indication of an oil leak).
I rechecked the coolant and it looked like there was more in there than there was a few minutes before but i couldn't be sure, i was able to get the car restarted and headed towards home (about 2 miles away).at this point i was able to get the car going at around 25-45mph on the next sharp corner i turned the engine died again so i restarted and kept going, it died once more right before i reached the driveway but i was able to coast the rest of the way, once i parked the car i turned the engine off and tried to restart it a minute later and it started again so i left it be and called someone to bring me some oil, when they got to me with the oil i put some in and and it would not start at all.
- I checked one of the spark plug wires and it is not getting any spark.
- The ground terminal on the battery seems to be stripped
- The battery / altenator / starter---- All read to be between 12.15 and 12.36 volts
- The head lights, instrument panel and such still turn on properly.
I'm at a loss here, it was just in the shop 20 days ago and now it isn't working again. I would prefer to not have to put it back in the shop, if it might be something i could repair from home.
View 4 Replies
I have a 92 ranger 6cyl 4L. The truck stopped running while driving then kicked on again, it did this several times over about 20 minutes then finally died and now I can't get it started. I recently replaced the fuel pump and filter and spark plugs and wires. I get spark if I ground the plug and some gas will pour out of the fuel pressure test valve when I stick a screws driver in. When I check engine codes I get an all pass. Truck will turn over and sometimes run for 2 or 3 seconds but that is it.
View 2 Replies
I have a 01 F550 Super Duty with a dynamic wheel lift system. One of my drivers was driving the truck when it just stopped running. I can't figure out what's happened. I think I have checked everything and yet it just turns over but won't start...
View 1 Replies
I recently bought Lumina 2004 LS. both radiator fan clicks when temperature is very high (about to reach red). Also I have noticed when the AC switched on fans are not running continuously, works for few seconds and went off.
I have already tried replacing the thermostat and two relays. What to check? Looking for wiring diagram for Radiator fans.
View 1 Replies
