What a Serpentine Belt is? (how much is it for that part alone and to install at the dealership?)
Dealership told me why during the cold mornings after I start the car up, it is creaking and squeaking........
They told me it needs to be replaced?......
Well, started to get belt squeak during cold starts. The idler pulley was changed many miles ago for same issue, but it seems to be starting up again. There are NO tutorials for serpentine belt replacement on this gen of RX.
View 14 RepliesI've been hearing a slight squeaking near the belt area. It's not continuous. Does it for a second then stops for a second and continues.
I hear it a lot more when I put the heat on through the top window (defroster). Never noticed it until it started getting cold. You think it might just be the belt? Or what?
So this car has only 50k miles. It was really cold in the sierra (around 20F) and the car started making a squeaking sound. I assumed it was just belt warming up, but when I opened the hood later, I saw shredded plastic. No CEL's! Seems to run smooth.
Where this came from? Is it part of the serpentine belt system?
I just replaced the original serpentine belt at 95k miles (more preventative than anything) and now it's squeaking. Does this mean I have to replace the tensioner?
View 11 RepliesLong story short is, I replaced my 2007 Santa Fe's serpentine belt and it still squeals for some time after we start the vehicle (then stops) ... but more importantly I *think* its still slipping if we're driving during rain or on very wet roads.
Long story long is ... the problem appeared as loss of power steering and air conditioning when driving during rain. Took it to the dealer and they suggested to replace the serpentine belt, replace the shroud (plastic) that covers the belt, and replace the timing belt. As we have 36k miles on it, no one I talked to understood the timing belt suggestion. I see though perhaps its just because the car is 4 years old? The shroud the dealer claimed was cracked and may be letting water in on to the belt. However, they completely removed it and did not replace it so I was not able to inspect this myself (wife took the car in for the appointment).
I bought the new belt and put it on. The squeaking was gone but as soon as I hit rain again, the slipping was back as bad as before (and we'd lose power steering / air conditioning same as before). I had a 1.5 hour drive in rain where the belt was slipping almost nonstop; constant back and forth between catching and slipping.
When the replacement shroud came in I thought that might solve the problem - keeping moisture off the belt. However with that in place I'm afraid there is still some slippage as I've noticed some dashboard lights come on during brief heavy rain. Also the initial squeaking is back when we start the car.
So i have a 1998 4.0 ohv ranger and have been fighting belt squeak shortly after i got it. I've replaced the belt twice and the tensioner twice when i put a GATES belt on it stopped for like month. But its still squeaking. If i put a wrench on the tensioner and turn it the squeak stops. So i need to find a way to tighten the tensioner could i somehow jam it, our hook up a turn buckle bolt to manually tighten it, or use a different ford tensioner. I really need to do something cause this squeak is just down right annoying.
View 2 RepliesI noticed my serpentine belt started squeaking about 3 days ago. And yesterday as I was driving to work I heard a clicking sound coming from the left side of the hood, then my car started to gradually shut down and white smoke was coming from the engine. When I got to the stoplight it completely turned off, but I was able to turn it back on again to turn into the parking lot before it shut off again. When I checked it there were no visible leaks, my reservoir for my coolant was still full, and my meter never went up indicating that my car was over heating. I'm not sure what's wrong with it, but after it sits for awhile it is able to turn back on again for a while.
View 3 RepliesI have a problem with my 1997 aerostar. There is a squeaking noise that gets more significant when I turn. I am pretty sure this is the drive belt as the power steering fluid is fine. Should I attempt to replace the belt tensioner and if so is it just the pulley that needs replacing or the whole tensioner. I am by no means a mechanic but can figure most things out.
View 5 RepliesI have a 2006 rx330 with belt squeaking noises on after warming up for say 10 mins on cold mornings, while reaching home I could hear the noises on cold days, the outside temperatures usually 35 to 40 F happens. While driving no noises, only happen on cold days when temperature is above 50 no problem. Should I replace the belts, how many belts are involved ? Tensioner problems ?
View 1 RepliesI have a concern with my serpentine belt chirping when it's wet or cold. I have tried soap, and other attempts to quiet it down. Belt tension is good, new water pump and fan. Otherwise no other issues so far.
View 9 RepliesI was wondering because serpentine belt is a big thing for 05 corolla since everything runs on it. I also had a 94 camry which had a alternator connected to a belt. and if i wanted to tighten up that belt i would just loosen the alternator and pull it. Is there a way to tighten up serpentine belt in my 05 corolla in the same way?.
View 1 RepliesWhen it is cold out or wet my serpentine belt squeals a lot or a couple of minutes. It had progressively gotten worse this past winter. The shop said the belt looks fine and Toyota wants me to pay for them to look at it...
View 2 RepliesI have a '06 sonata 3.3 v6. Let me first describe what was happening to the car before the noise started. When I first started the car and put the ac, the first time turning the steering wheel in either direction the steering wheel would tighten up and the battery indicator light would come on and the fasten seatbelt light would flash even though I had the belt fastened. It would only happen the first time I would make a turn and after that I could turn with no problem. So in recap, it would only happen on the first turn and only when the ac was on. Now when I start the car up there is a noise coming form the pulley/belt area. I wouldn't classify it as a squeaking noise more like a grinding. I've looked at the belt and it seems to be fine. After I start to drive the car the noise goes away. If I start the car again after a drive within about 2 hours the noise doesn't happen when I start it. What this noise could be? and also could the noise and the steering wheel tightening when the ac is on be connected?
View 1 RepliesThe serpentine belt starting squeaking on cold and damp mornings about 18 months ago at about 60K. I replaced it with a Dayco belt, and the noise went away for about 6 months. When the weather turned cold last winter, the noise came back. So I changed the tensioner with both idler pulleys right about when the weather warmed up, and it was fine all summer. Now that it has gotten cold again, the squeak is back yet again and as before it goes away when the car warms up. I know it is the serpentine belt because when I spray it with water the noise immediately stops. I checked all the pulleys with the belt off and when I spin them I hear no noise. Is there something else it could be?
View 1 RepliesI have changed belts on other cars just never a Lexs. how hard is it to do on or trucks?
View 7 RepliesI have a 2007 ES350 with over 65 k miles on the clock. I would like to change the serpentine belt as a preventive measure. Looking for a procedure on changing this belt? Pics ???
View 4 RepliesMy tensioner pulley is making noise.I replaced the rear idler pulley (can't get to the front one), but still have the noise. Mention a DIY for replacing the tensioner pulley bearing. A part number for the bearing?
View 2 RepliesI have a 2007 ES350. It started making a vibrating noise and sometimes screech coming from the serpentine belt area. It stops when I turn off the A/C and also stops when I accelerate with the A/C on (only does it when idling).
View 3 RepliesSerpentine belt on a 2006 Honda Odyssey fraying and then ripping into the timing belt causing that belt to break? I recently had this scenario given to me as the cause of my recently replaced timing belt breaking.
View 11 Replies2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.